Service parts for the Panda PMS 8 mini E-TEC
Grouped by system, with how many of each the parts manual calls for.
Air intake
1 requiredFuel system
1 requiredOil system
1 requiredBelts
1 requiredCooling system
1 requiredElectrical
1 requiredIgnition
1 requiredPrices captured from merchant listings; some links are affiliate links. Confirm against your serial number before ordering.
Specifications
| Oil capacity | 3.8 L |
|---|
Engine
| Oil capacity | 3.8 L |
|---|---|
| Coolant capacity | 3.8 L |
| Displacement | 0.479 L |
| Aspiration | naturally aspirated |
| Rated speed | 2800 rpm |
Filters for the Kubota Z482
1Engine-mounted filters the filter manufacturers list for this engine family. These come from the engine, not from this generator set’s own parts list, so confirm against your serial number before ordering.
Listed for this engine in only one kind of machine, so they may depend on how the engine was installed:
| System | Filter | Description | Cross-references | |
|---|---|---|---|---|
| Fuel filter | P550127 | Fuel Filter, Spin-On | KUBOTA 1522143170, KUBOTA 1522143171, NAPA 3390, WALGAHN-MOTORENTECHN 00811936 | KuduParts $16.00 |
Same engine, other brands
9 brandsThe Kubota Z482 in this set also powers 25 generator sets sold under 9 other brands. Service parts and maintenance intervals for the engine are shared; enclosure, alternator, controller and ratings are not.
| Brand | Models |
|---|---|
| Kubota | GL 7000, GL6000, GL6000-AUS, GL6000-STD, GL6000A-AU-B, GL6000D-AU-B, GL7000-STD, GL7000-USA, GL9000A-AU-B, J107 |
| Fischer Panda | 4000s SC, 8000i PMS, PMS 8 mini E-TEC, Panda 4K PMS, Panda 8000 NE, Panda 8000i PMS, Panda 8mini PMS Digital |
| MQ Power | DA-7000SS, DA7000SS |
| Cummins/Onan | MDKB |
| Denyo | DA-6000SS |
| FG Wilson | KH6-1S |
| Generac | MLTS |
| Paguro | 4000 |
| WhisperPower | Piccolo 8 |
Maintenance & consumables
for the Kubota Z482| Item | Spec | Capacity | Part # | Interval | |
|---|---|---|---|---|---|
| Air filter | air filter mat | s00585 | Amazon eBay | ||
| Fuel filter | 1522143081 | 1680 hr | Amazon eBay $37.58 KuduParts $13.00 FridayParts $15.69 | ||
| Oil filter | oil filter | s00585 | Amazon eBay | ||
| Battery | Check electrolyte level yearly for batteries used less than 100 hours in a year | G3102-8833-0 | 500 hr | Amazon eBay | |
| Belt | Check every 50 hours of operation, replace if necessary | G3102-8832-0 | 1000 hr | Amazon eBay | |
| Coolant | 50.0 L | — | 5000 hr | ||
| Coolant filter | Changing Coolant, Remedies for Rapid Coolant Loss | G3102-8831-0 | 200 hr | Amazon eBay | |
| Hydraulic filter | — | ||||
| Oil | 4.7 l | — | 800 hr | ||
| Spark plug | Replace as needed based on operating conditions | G3102-8836-0 | Amazon eBay |
Service intervals
6| Item | Action | Hours | Months | Notes |
|---|---|---|---|---|
| Engine oil | Change | 100 hr | First service — First oil change after 35 to 50 hours. | |
| Oil filter | Change | 100 hr | First service — Inspection checklist row 05; change at first service. | |
| Actuator spiral thread spindle | Lubricate | 100 hr | Every 100 h. | |
| V-belt for internal cooling water pump | Check | 100 hr | Control interval 100 operating hours. | |
| Fuel filter | Replace | 300 hr | At least every 300 operation hours; sooner if fuel contaminated. | |
| Coolant connection block (sacrificial anode) | Replace | 12 mo | At least once per year if corrosion visible. |
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Service specifications
49| Type | Item | Value | Unit | Condition |
|---|---|---|---|---|
| Clearance | Capsule underside to base plate clearance | min. 12 | mm (1/2 inch) | |
| Clearance | External cooling water expansion tank lower edge above sound cover upper edge | 500 | mm | minimum |
| Clearance | Vent valve height above waterline | 600 | mm | minimum |
| Gap | Speed sensor air gap | 0.3 to 0.8 | mm | between sensor tip and gear tooth tips |
| Other | Actuator fuse on control printed circuit board | 1.6 | A miniature slow-to-blow fuse | |
| Other | Booster capacitors | 2x30 | µF | |
| Other | Cooling water requirement for raw water circuit | 16-28 | l/min | |
| Other | Excitation capacitors | 2x100 | µF | |
| Other | Exhaust hose inner diameter | 40 | mm | |
| Other | Exhaust system total length without separator | 6 | m | max |
| Other | Fuel consumption | ca. 0.84 - 2.24 | l | 30% to 80% of power rating; 0.35 l/kW electrical power |
| Other | Lower switching point time lag | 40 | seconds | |
| Other | Max power (DIN 6271-NB) at 3600 rpm | 12,5 | kW | |
| Other | Maximum speed increase by VCS | up to 8 | % | |
| Other | Oil consumption | max. 1 | % of fuel consumption | |
| Other | Raw water intake inner diameter | 1 | inch (25 mm) | minimum |
| Other | Starter battery cable cross-section | 25 | mm² | |
| Other | Upper switching point time lag | min. 20 | seconds | |
| Other | V-belt deflection | approx. 1 | cm | pressing with thumb |
| Pressure | Compressed air for purging cooling system | about 0.5 | bar | |
| Pressure | Exhaust back pressure | 0.4 | bar | max |
| Pressure | Fuel pump suction height | 1.2 | m at 0.2 bar | max |
| Resistance | Inductive resistance H1/H2 | 0.635 | mH | |
| Resistance | Inductive resistance Z1/Z2 | 4.945 | mH | |
| Resistance | Ohmic resistance H1/H2 | 0.175 | Ohm | |
| Resistance | Ohmic resistance Z1/Z2 | 0.68 | Ohm | |
| Speed | Frequency with no load (VCS) | approx 57,8 to 58,6 | Hz | no load |
| Speed | Idle running speed | 3510 | rpm | progressive governor by VCS |
| Speed | Rated speed | 3600 | rpm | |
| Temperature | Ambient temperature power derating | 2% per 5°C rise above 40°C | % per °C | |
| Temperature | Anti-freeze mixture good for at least | -15 | °C | |
| Temperature | Coolant in-flow and return temperature difference | approx. 10 | degrees | under operation |
| Temperature | Engine room temperature relative to outside | should not be higher than 15 | °C | |
| Temperature | Thermo-sensor at watercooled exhaust elbow | 120/105 | °C | |
| Temperature | Thermo-switch at cylinder head | 110 and 130 | °C | |
| Temperature | Thermo-switch at exhaust connection | 98/83 | °C | |
| Temperature | Thermo-switch at front plate | 120 | °C | |
| Temperature | Thermo-switch in generator coil | 4x160 | °C | |
| Voltage | Generator output voltage too low, 60 Hz | less than 100 | V | |
| Voltage | Generator voltage too high, 60 Hz | more than 135 | V | |
| Voltage | Generator voltage with no load (VCS) | 240 | V | no load, 60 Hz |
| Voltage | Insulation test voltage housing to AC-Control box or ground | must not exceed 50 | mV | |
| Voltage | Lower speed voltage limitation | 230 | V AC | no load |
| Voltage | Maximum upper speed voltage limitation | 270 | V AC | no load |
| Voltage | Normal voltage range, 60 Hz version | 100 - 130 | V | |
| Voltage | Starter battery voltage drop during starting | 11 | V | fully charged battery |
| Voltage | VCS J1 power supply | +9....18V DC or +18...36V DC | V DC | |
| Voltage | Voltage controller lower switching point | 11.52 | V | factory setting |
| Voltage | Voltage controller upper switching point | 13.6 | V | factory setting |
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Recommended fluids
| Fluid | Grade | Standard | Ambient | Capacity | Notes |
|---|---|---|---|---|---|
| Coolant | GLYSANTIN PROTECT PLUS / G48 | antifreeze suitable for aluminium | Mixture ratios: 70:30 -20°C; 65:35 -25°C; 60:40 -30°C; 55:45 -35°C; 50:50 -40°C. | ||
| Engine oil | SAE10W | API C (diesel) | below 0°C | 2.1 l | Alternative SAE10W-30 or SAE10W-40. Section B.2 gives SAE10W or 10W-30 under 5°C. |
| Engine oil | SAE20 | API C (diesel) | 0°C to 25°C | 2.1 l | Alternative SAE10W-30 or SAE10W-40. Section B.2 gives SAE20 between 5°C and 20°C. |
| Engine oil | SAE30 | API C (diesel) | above 25°C | 2.1 l | Alternative SAE10W-30 or SAE10W-40. Section B.2 gives SAE30 for temperatures over 20°C. |
| Fuel | Diesel | recommended 2-D Diesel | |||
| Grease | Antiseize grease | For spindle and screws at actuator; use electrically neutral fat on coolant connection block fixing bolts. | |||
| Other | Glycerin or non-mineral oil based lubricant e.g. silicone spray | For lubricating impeller before reinsertion. |
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Procedures
12Adjustment of the maximum upper speed adjustment
Tools: wrench SW 10, AC voltmeter 300 V
- Disconnect actuator electrical supply plug.
- Unclamp countering nut at limitation screw with wrench SW 10.
- Connect AC voltmeter up to 300 V to AC outlet.
- Ensure no electrical load is switched on.
- Start generator.
- Turn actuator spindle manually until voltmeter reads 270 V.
- Tighten limit stop screw against speed regulator lever.
- Secure with countering nut; check voltage limited to 270 V no load.
Adjustment of the normal speed limitation adjustment
Tools: two wrenches SW 14, AC voltmeter 300 V
- Disconnect actuator electrical supply plug.
- Unclamp countering nuts with two wrenches SW 14.
- Connect AC voltmeter up to 300 V to AC outlet.
- Ensure no electrical load is switched on.
- Start generator.
- Turn actuator spindle manually until voltmeter reads 230 V.
- Tighten both nuts.
- Check lower voltage limited to min. 230 V no load.
Insulation test diagnostic
Tools: voltmeter (Volt/AC)
- Switch off all on-board electrical devices.
- Start generator.
- Measure AC voltage between generator housing and AC-Control box.
- Measure AC voltage between generator housing and ground.
- Measured voltage must not exceed 50 mV.
- Check safety systems and leakage current relay if installed.
- Ensure all electrical devices connect to common ground.
De-aerating of the coolant circuit maintenance
⚠ Do not open cooling water pump de-aerating screw while generator runs.
- Stop generator before opening de-aerating points.
- Open de-aerating screw at cooling water pump.
- Open de-aerating screw at thermostat housing.
- Fill coolant at filler neck until level stops falling.
- Close filler cap and de-aerating screws.
- Start generator; repeat de-aeration several times.
- Check external expansion tank filled to max mark.
De-aerating the fuel system maintenance
Tools: cloth or absorbent paper
- Switch 'Stand by' switch on control panel to ON.
- Push and hold fuel purge switch S2; electric fuel pump must run audibly.
- Run fuel pump 3 to 4 minutes.
- Open bleeding screw on fuel solenoid valve while still pressing switch.
- Place cloth under connection to catch fuel.
- Close bleeding screw when fuel runs without bubbles.
- Release switch and start unit with Run/Stop button.
- If no start, loosen injection nozzle pipe union and retry; tighten after start.
Exchange of the V-belt for internal cooling water pump maintenance
- Loosen fixing screw above alternator.
- Loosen fixing screw below alternator only a little.
- Press alternator toward thermostat housing.
- Replace V-belt type XPZ 850.
- Pull alternator back to tension belt.
- Belt should deflect approx. 1 cm with thumb.
- Tighten fixing screws above and below alternator.
Exchange of the fuel filter maintenance
- Clamp fuel inlet line before filter.
- Remove hoses from used filter.
- Fasten hoses to new filter, observing arrow for fuel flow direction.
- Check for leaks.
Exchange of the impeller maintenance
Tools: multigrip pliers
- Close raw water stop cock.
- Remove raw water pump cover screws and cover.
- Pull impeller from shaft with multigrip pliers.
- Check impeller for damage; replace if necessary.
- Lubricate impeller with glycerin or silicone spray.
- Install impeller in correct position.
- Fit cover with new seal.
Exchange the air filter maintenance
- Loosen six screws on air suction housing cover.
- Open air suction housing.
- Change air filter mat.
- Reassemble cover.
Execution of an oil change maintenance
Tools: oil filter strap, wrench, hand pump (optional)
- Open oil drain screw and drain oil into container.
- Close oil drain screw.
- Remove oil filter with oil filter strap.
- Coat new oil filter gasket with oil.
- Tighten oil filter by hand.
- Open oil filler neck and refill oil.
- Wait, then check oil level on dipstick; recommended 2/3.
Preparation for winter storage maintenance
- Rinse raw water circuit with anti-freeze solution.
- Check anti-freeze concentration in internal cooling circuit.
- Clean raw water filter and check seal.
- Check all hoses and hose connectors.
- Remove impeller, grease with vaseline, store in dark place.
- Disassemble, check and grease vent valve.
- Disconnect starter battery positive and negative poles.
- Lubricate speed adjustment spindle with Antiseize grease.
Rotor re-magnetizing repair
⚠ Do not use battery bank or generator starter battery; this could damage the coil.
Tools: 9 V battery
- Switch off shore power and interrupt any AC source connection.
- Switch generator off; do not operate starter.
- Set power source selector to generator.
- Connect only plug socket to generator.
- Connect two poles of a 9 V battery to plug socket.
- Apply DC voltage only 1 to 2 seconds.
- Start generator normally.
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Voltage reconnection
| Voltage | Phase | Connection | Leads | Notes |
|---|---|---|---|---|
| DVS - 50Hz | L1, L2, L3, L1’ | Contacts to check between coil connection points and housing (PE). | ||
| HP1 - 50Hz | L, Z | Contacts to check between coil connection points and housing (PE). | ||
| HP3 - 50Hz | L1, L2, L3 | Contacts to check between coil connection points and housing (PE). | ||
| 120 V | HP1 - 60Hz | L, Z | Contacts to check between coil connection points and housing (PE). | |
| 120 V | HP3 - 60Hz | L1, L2, L3, 1, 2, 3, 4 | Contacts to check between coil connection points and housing (PE). | |
| 120 V / 240 V | DVS - 60Hz | L1, L2, L3, L1’, 1, 2, 3, 4 | Contacts to check between coil connection points and housing (PE). |
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Common questions
What engine is in the Icemaster GmbH (Fischer Panda) Panda PMS 8 mini E-TEC?
The Icemaster GmbH (Fischer Panda) Panda PMS 8 mini E-TEC is powered by the Kubota Z482 engine.
How much oil does the Icemaster GmbH (Fischer Panda) Panda PMS 8 mini E-TEC take?
The Kubota Z482 engine in the Icemaster GmbH (Fischer Panda) Panda PMS 8 mini E-TEC has an oil capacity of 3.8 liters.
What is the cooling system capacity of the Icemaster GmbH (Fischer Panda) Panda PMS 8 mini E-TEC?
The Icemaster GmbH (Fischer Panda) Panda PMS 8 mini E-TEC cooling system holds 3.8 liters (1.0 US gallons) for the engine, per the manufacturer specification sheet.
Which oil filter part number does the Icemaster GmbH (Fischer Panda) Panda PMS 8 mini E-TEC take?
The Icemaster GmbH (Fischer Panda) Panda PMS 8 mini E-TEC uses oil filter part number s00585.
What fuel filter fits the Icemaster GmbH (Fischer Panda) Panda PMS 8 mini E-TEC?
The Icemaster GmbH (Fischer Panda) Panda PMS 8 mini E-TEC uses fuel filter part number 1522143081.
What air filter fits the Icemaster GmbH (Fischer Panda) Panda PMS 8 mini E-TEC?
The Icemaster GmbH (Fischer Panda) Panda PMS 8 mini E-TEC uses air filter part number s00585.
Repair guides
12- Adjustment of the maximum upper speed
- Adjustment of the normal speed limitation
- De-aerating of the coolant circuit
- De-aerating the fuel system
- Exchange of the fuel filter
- Exchange of the impeller
- Exchange of the V-belt for internal cooling water pump
- Exchange the air filter
- Execution of an oil change
- Insulation test
- Preparation for winter storage
- Rotor re-magnetizing
Step-by-step procedures compiled from the Icemaster GmbH (Fischer Panda) service manual for this model.
Parts
78| Part # | Description | Qty | System | |
|---|---|---|---|---|
| 02-105-001 | Air filter mat | 1 | Air filter | Amazon eBay |
| 02-105-002 | Pull out holder for air filter mat | 1 | Air filter | Amazon eBay |
| 02-105-003 | Snap fasteners for air filter housing | 1 | Air filter | Amazon eBay |
| 02-106-001 | Fuel filter with sight glass (optional) | 1 | Fuel filter | Amazon eBay |
| 07909-30241 | Plastigage | Plastigage | Amazon eBay | |
| 07909-31371 | Red Check | Red check | Amazon eBay | |
| 07909-31661 | Connecting Rod Alignment Tool | Connecting rod alignment tool | Amazon eBay | |
| 07909-33102 | Valve Seat Cutter | Valve seat cutter | Amazon eBay | |
| 07916-09032 | Special Use Puller Set | Special use puller set | Amazon eBay | |
| 07916-32011 | Flywheel Puller | Flywheel puller | Amazon eBay | |
| 07916-32032 | Oil Pressure Tester | Oil pressure tester | Amazon eBay | |
| 07916-34041 | Auxilary Socket for Fixing Crankshaft Sleeve | Auxiliary socket for fixing crankshaft sleeve | Amazon eBay | |
| 21.03.02.005S | Impellerfilter spare part kit | 1 | Impeller | buy |
| 31.06.03.003P | Impellerfilter for Marine Panda P6, P8, P9, P10, P12 and P14 (tested for a flow rate up to 22 l/min) | 1 | Impeller | buy |
| F100-0250 | Air Filter | 1 | Air filter | Amazon eBay |
| F100-0300 | Oil Filter | 1 | Oil filter | Amazon eBay |
| F100-0450 | Fuel Filter | 1 | Fuel filter | Amazon eBay |
| F100-0600 | Coolant Filter | 1 | Coolant filter | Amazon eBay |
| F100-0750 | Belt | 2 | Belt | Amazon eBay |
| F100-1000 | Battery | 1 | Battery | Amazon eBay |
| F100-1250 | Spark Plug | 4 | Spark plug | Amazon eBay |
| F1379 | Siphon Break Kit | Siphon break | Amazon eBay | |
| G3102-10011 | Rotor Pulling Out Bolt (for GL6000, GL7000) | Rotor pulling out bolt | Amazon eBay | |
| G3102-8830-0 | Gasket | 1 | Gasket | Amazon eBay |
| G3102-8831-0 | Coolant filter | 1 | Coolant filter | Amazon eBay |
| G3102-8832-0 | V-belt | 1 | Belt | Amazon eBay |
| G3102-8833-0 | Battery | 1 | Battery | Amazon eBay |
| G3102-8836-0 | Spark plug | 1 | Spark plug | Amazon eBay |
| G3102-8838-0 | Fuel filter | 1 | Fuel filter | Amazon eBay |
| G3102-8839-0 | Air cleaner | 1 | Air filter | Amazon eBay |
| G3102-8841-0 | Oil filter cartridge | 1 | Oil filter | Amazon eBay |
| GL6000 | Fuel filter cartridge or element | Fuel filter | Amazon eBay $372.35 FridayParts $22.74 | |
| HH150-32094 | OIL FILTER | Oil filter | Amazon eBay $19.99 NAPA $9.64 KuduParts $17.00 FridayParts $18.90 | |
| HH150-32430 | OIL FILTER | Oil filter | Amazon Amazon eBay $39.49 eBay $17.99 NAPA $9.64 KuduParts $11.00 FridayParts $13.16 | |
| P01-001 | Air Filter | 1 | Air filter | Amazon eBay |
| P02-001 | Oil Filter | 1 | Oil filter | Amazon eBay |
| P03-001 | Fuel Filter | 1 | Fuel filter | Amazon eBay |
| P04-001 | Coolant Filter | 1 | Coolant filter | Amazon eBay |
| P05-001 | Belt | 2 | Belt | Amazon eBay |
| P06-001 | Spark Plug | 1 | Spark plug | Amazon eBay |
| P100-001 | Air filter mat | 1 | Air filter | Amazon eBay |
| P100-002 | Oil filter | 1 | Oil filter | Amazon eBay |
| P100-003 | Fuel filter | 1 | Fuel filter | Amazon eBay |
| P100-004 | Coolant filter | 1 | Coolant filter | Amazon eBay |
| P100-005 | Belt for internal cooling water pump | 1 | Belt | Amazon eBay |
| P100-006 | Thermostat | 1 | Thermostat | Amazon eBay |
| P100-007 | Impeller | 1 | Impeller | Amazon eBay |
| P100-008 | Injection nozzle | 1 | Injector | Amazon eBay |
| P100-009 | Glow plug | 1 | Glow plug | Amazon eBay |
| Ref/P100-001 | Air filter mat | 1 | Air filter | buy |
| Ref/P100-002 | Fuel filter | 1 | Fuel filter | buy |
| Ref/P100-003 | Oil filter | 1 | Oil filter | buy |
| Ref/P100-004 | Battery | 1 | Battery | buy |
| Ref/P100-005 | Glow plug | 1 | Glow plug | buy |
| Ref/P100-006 | Injection nozzle | 1 | Injector | buy |
| W1020554 | Damage in Electric Wiring and Loose Connections | 1 | Air filter | Amazon eBay |
| W10252400 | Injection Pump Pressure Tester | Injection pump pressure tester | Amazon eBay | |
| W1037215 | Engine Oil Filter Cartridge | 1 | Oil filter | Amazon eBay |
| W1040289 | Idle Gear Bushing Replacing Tool | Idle gear bushing replacing tool | Amazon eBay | |
| W1053554 | Battery | 2 | Battery | Amazon eBay |
| W1062553 | Connecting Rod Small End Bushing Tool | Connecting rod small end bushing tool | Amazon eBay | |
| 12567 | Canopy HardHat® | Service part / kit | Amazon eBay | |
| 21.02.02.009H | Generator Control Panel P6+ (12V version, RE0703) | 1 | Service part / kit | buy |
| 21.02.02.015H | Option master-slave adapter | 1 | Service part / kit | buy |
| 21.02.02.016H | Option automatic adapter | 1 | Service part / kit | buy |
| 21.02.02.046H | Generator Control Panel P6+ 12V version | 1 | Service part / kit | buy |
| 21.02.02.047H | Generator Control Panel P6+ 24V special version | 1 | Service part / kit | buy |
| 21.03.10.008P | Service Kit 8 | Service part / kit | buy | |
| 21.03.10.009P | Service Kit 9 | Service part / kit | buy | |
| 21.03.10.026P | Plus service kit 16 | Service part / kit | buy | |
| 21.03.10.027P | Plus service kit 17 | Service part / kit | buy | |
| G3907-8830-0 | Danger/warning/caution label (2) | Service part / kit | eBay | |
| G3907-8832-0 | Danger/warning/caution label (1) | Service part / kit | eBay | |
| PMGPN610U19 | Cap 19 mm | 2 | Service part / kit | eBay |
| W1022492 | Intake and exhaust valve clearance (Cold) | 1 | Service part / kit | Amazon eBay |
| W1024734 | Ball Bearing | 1 | Service part / kit | Amazon eBay |
| W10411400 | Radiator Cap | 1 | Service part / kit | Amazon eBay |
| s00585 | Generator Failure | Service part / kit | Amazon eBay |
Service, wear & replacement parts referenced for this model and its engine — confirm the exact part for your serial number. See the full parts catalog to search and cross-reference.
Available documents
Service manual — Panda PMS 8mini E-TEC Installation Manual (Icemaster GmbH (Fischer Panda))
This page was generated from the 1 manufacturer document above by automated extraction; every figure shown is copied from one of them. How the data is compiled.