Service parts for the QT 3.9L 40kW
Grouped by system, with how many of each the parts manual calls for.
Air intake
1 requiredBelts
1 requiredCooling system
1 requiredElectrical
1 requiredIgnition
1 requiredPrices captured from merchant listings; some links are affiliate links. Confirm against your serial number before ordering.
Specifications
| Fuel | Natural Gas, Propane Vapor |
|---|---|
| Frequency | 60.0 Hz |
| Standby power | 40 kW |
| Controller | R-100 |
| Oil capacity | 3.8 L |
| Voltage options | 120/240 V, 120/208 V, 277/480 V |
| Phase | 1-phase or 3-phase |
| Power factor | 1.0 (single-phase), 0.8 (three-phase) |
| Battery group | 24F |
| Battery cranking | 525 CCA |
| Battery voltage | 12 Volts V |
| Max ambient | 50 °C |
Engine
| Oil capacity | 3.8 L |
|---|---|
| Coolant capacity | 4.0 L |
| Displacement | 3.9 L |
| Aspiration | Naturally Aspirated |
| Rated speed | 1800 rpm |
Maintenance & consumables
for the Generac V-type| Item | Spec | Capacity | Part # | Interval | |
|---|---|---|---|---|---|
| Air filter | Air Cleaner | 0A4637 | 500 hr | Amazon eBay $49.95 NAPA $13.61 | |
| Fuel filter | — | 1000 hr | |||
| Oil filter | 0E7415 | 150 hr | Amazon eBay $81.99 NAPA $3.59 | ||
| Battery | BCI Group 24F-6, 535 CCA @ 0 deg. F (spec sheet recommends 24F 525CCA) | 058208 | Amazon eBay | ||
| Belt | 60.5" | 0D3488H | Amazon eBay $49.99 | ||
| Coolant | Half low silicate ethylene glycol base anti-freeze and deionized water (50-50 mixture) | 046627 | Amazon eBay $15.00 | ||
| Coolant filter | — | 1000 hr | |||
| Oil | Engine crankcase oil level | — | 1000 hr | ||
| Spark plug | Gap 1.01 mm (0.040 inch); Champion # RC12LC4 | RC12LC4 | Amazon eBay $26.61 |
Service intervals
29| Item | Action | Hours | Months | Notes |
|---|---|---|---|---|
| Unit (Service Schedule Level 1) | Inspect | 10 hr | 1 mo | Recommended: monthly / 10 hrs |
| Engine Oil Level | Check | 20 hr | At least every 20 hours of operation, or prior to use | |
| Engine oil level / crankcase oil | Check | 20 hr | Check at least every 20 hours of operation, or prior to use | |
| Engine oil (break-in oil) | Change | 30 hr | First service — Engine shipped with break-in oil; change after 30 hours of operation | |
| Unit (Service Schedule Level 2 break-in) | Inspect | 30 hr | 3 mo | First service — Wear-in inspection performed ONLY ONCE following first three months or first 30 hours |
| Unit (Service Schedule Level 3) | Inspect | 50 hr | 6 mo | Semi-annually or following each 50 hours |
| Engine oil and oil filter | Change | 150 hr | 6 mo | First service — First 100 operating hours; after initial change service at 150 operating hours or 6 months, whichever comes first |
| Unit (Service Schedule Level 4) | Inspect | 100 hr | 12 mo | Annually or following each 100 hours |
| Unit (Service Schedule Level 5) | Inspect | 250 hr | 24 mo | Annually or following each 250 hours |
| Air cleaner | Check | 500 hr | EVERY 500 OPERATING HOURS - service air cleaner | |
| Air cleaner | Other | 500 hr | Every 500 operating hours: service air cleaner | |
| Engine DC alternator | Check | 500 hr | Every 500 operating hours | |
| Starter | Check | 500 hr | Every 500 operating hours | |
| Battery state of charge and condition | Check | 3 mo | Maintenance performed by authorized service facilities | |
| Cooling system | Drain | 12 mo | Once annually flush cooling system | |
| Cooling system | Inspect | 1 mo | Inspect at least once each month; check hoses and clamps | |
| Cooling system | Other | 12 mo | Once annually: flush cooling system / drain, flush and refill | |
| Engine Cooling System | Inspect | 1 mo | At least once each month; check hoses and hose clamps | |
| Engine governor | Test | 12 mo | Once annually; adjust or repair if needed | |
| Engine ignition system | Check | 3 mo | Every three months | |
| Engine safety devices (low oil pressure, low coolant level, high coolant temperature) | Test | 6 mo | Once every six months | |
| Engine-generator (visual) | Inspect | 1 mo | Complete a thorough visual inspection monthly | |
| Engine-generator visual inspection | Inspect | 1 mo | Monthly: check for damage, loose/corroded fasteners, fuel/oil/coolant leaks | |
| Exhaust system | Inspect | 3 mo | Inspect at least once every three months; check pipes, mufflers, clamps | |
| Fan belts | Check | 3 mo | Inspect every three months; replace defective belt; check tension (3/8 to 5/8 inch deflection) | |
| Fuel system | Inspect | 3 mo | Inspect and test fuel system | |
| Fuel system | Test | 3 mo | Every three months: inspect and test fuel system | |
| Generator | Clean | 12 mo | Once annually: clean and inspect generator; check stator/rotor insulation resistance | |
| Transfer switch | Check | 3 mo | Every three months |
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Service specifications
32| Type | Item | Value | Unit | Condition |
|---|---|---|---|---|
| Clearance | Fan belt deflection (force of approx. 22 pounds / 10 kg applied midway between pulleys) | 3/8 to 5/8 | inch (10 to 16 mm) | midway between pulleys |
| Gap | Spark plug gap | 1.01 | mm (0.040 inch) | |
| Gap | Spark plug gap | 1.01 mm (0.040 inch) | mm (inch) | |
| Other | Altitude deration | 1% for every 100 m above 183 m; 3% for every 1000 ft above 600 ft | ||
| Other | Coolant capacity | 3.0 | U.S. gal | |
| Other | Crankcase oil capacity | 4 | U.S. qts (3.8 liters) | |
| Other | Fan belt tension (thumb pressure) | deflect about 3/8 to 5/8 inch | inch | Midway between pulleys |
| Other | Fan belt tension/deflection (force applied midway between pulleys) | 22 pounds (10 kg) force deflects belt about 3/8- to 5/8-inch (10 to 16 mm) | pounds (kg) / inch (mm) | Applied midway between pulleys |
| Other | Generator locked rotor kVA available @ 35% voltage dip | 80 | KVA | single-phase or 208V, 3-phase |
| Other | Generator locked rotor kVA available @ 35% voltage dip | 90 | KVA | 480V, 3-phase |
| Other | Telephone interference factor (TIF) | < 50 | ||
| Other | Total harmonic distortion | < 3.5 | % | |
| Pressure | Compression ratio | 9.1-to-1 | ||
| Pressure | Gas pressure at inlet to fuel shutoff solenoid (must not exceed) | 14 | inches water column (0.5 psi) | |
| Pressure | Low oil pressure switch setpoint | 8 | psi | |
| Pressure | Low oil pressure switch setting | 8 | psi | contacts close below this pressure |
| Pressure | Operating fuel pressure (natural gas and propane vapor) | 5 to 14 | in. water column (0.18 to 0.5 psi) | |
| Pressure | Optimum pressure at fuel shutoff solenoid | 11 | inches water column (0.4 psi) | |
| Pressure | Required fuel pressure (natural gas / liquid propane) | 5 inches to 14 inches water column (0.18 to 0.5 psi) | inches water column (psi) | |
| Speed | Fan speed | 2060 | rpm | |
| Speed | Governor steady state regulation | ± 0.25 | % | isochronous |
| Speed | Rated synchronous RPM | 1800 | rpm | 60 Hz |
| Temperature | Exhaust temperature at rated output | 938 | °F | 60 Hz rated output |
| Temperature | High coolant temperature switch setting | 140 | °C (284°F) | |
| Temperature | High coolant temperature switch trip point | approximately 140 | °C (284° F) | |
| Temperature | Maximum ambient temperature | 50 | °C (140°F) | |
| Temperature | Maximum operating air temp. on radiator | 60 | °C (150°F) | |
| Temperature | Temperature deration | 3% for every 10 | °C above 25°C; 1.65% for every 10°F above 77°F | |
| Voltage | Battery charge alternator | 12V, 30 | Amp | |
| Voltage | Static battery charger | 2 | Amp | |
| Voltage | System voltage | 12 | Volts | |
| Voltage | Voltage regulator regulation | ± 1 | % | single-phase sensing |
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Recommended fluids
| Fluid | Grade | Standard | Ambient | Capacity | Notes |
|---|---|---|---|---|---|
| Coolant | 50-50 mixture of low silicate ethylene glycol base anti-freeze and deionized water | 3.0 U.S. gal | Do not use chromate base rust inhibitor; high silicate boosters or soluble oil inhibitor not recommended | ||
| Coolant | Half low silicate ethylene glycol base anti-freeze and deionized water (50-50 mixture) | Low silicate anti-freeze; deionized water; high quality rust inhibitor optional | 3.0 U.S. gal. | Do not use chromate base rust inhibitor, high silicate anti-freeze boosters or soluble oil inhibitors | |
| Engine oil | 15W-40 | High-quality detergent oil classified "For Service CC, SD, SE, SF" | 4.0 U.S. qts (3.8 liters) | Factory fill is 15W-40 | |
| Engine oil | 5W-30 synthetic | below 0°C | For temperatures below 32°F (0°C); optional Cold Weather Start Kit recommended | ||
| Engine oil | SAE 20W-20 or 15W-40 | For Service SJ or SH | 0°C to 27°C | 32° to 80°F (0° to 27°C) | |
| Engine oil | SAE 30W or 15W-40 | For Service SJ or SH | above 27°C | 4.0 U.S. quarts | Above 80°F (27°C) use SAE 30W or 15W-40 (older manual); unit filled with 15W-40 at factory (newer manual: 5W-20, use 5W-30 on change) |
| Fuel | LP gas (Btu content at least 2,520 Btus per cubic foot) | Required fuel pressure 5 to 14 inches water column | |||
| Fuel | Natural gas (Btu content at least 1,000 Btus per cubic foot) | Required fuel pressure 5 to 14 inches water column | |||
| Fuel | Natural gas (min. 1,000 Btu per cubic foot) or LP gas (min. 2,520 Btu per cubic foot) | Fuel pressure 5 in. - 14 in. water column | |||
| Gear oil | SAE 90 gear lubricant | Generator gearbox (if equipped) |
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Procedures
12Reconfiguring the Fuel System (NG to LP) adjustment
⚠ Port 1 is for NG only and Port 2 is for LP vapor only. No provision for dual fuel has been made.
- Turn the main gas supply off.
- Remove the carburetor fuel hose from the outlet port (Port 1) of the demand regulator.
- Remove the brass hose fitting from the outlet port (Port 1).
- Remove pipe plug from Port 2.
- Install brass hose fitting into Port 2.
- Install pipe plug into Port 1.
- Connect carburetor gas hose to brass fitting.
- Tighten all clamps and plugs.
- Make sure fuel supply is of the proper pressure and type for configuration.
- Reverse the procedure to convert back to natural gas.
- The Dip switch inside the control panel must be in the LP or NG position when switching to different fuels.
Spark Plugs - Inspection and Gap Adjustment adjustment
Tools: wire feeler gauge, wire brush
- Clean area around base of the spark plugs using a wire brush and commercial solvent; do not blast the plugs.
- Remove the spark plugs and check condition; replace if worn or reuse is questionable.
- Check spark plug gap using a wire feeler gauge.
- Adjust gap to 1.01 mm (0.040 inch) by carefully bending the ground electrode.
Preparation for Start-Up installation
⚠ Ensure AUTO/OFF/MANUAL switch is in OFF position before working on the generator.
Tools: Manometer
- Ensure 120VAC circuit breaker to battery charger is open.
- Remove the fuse from the control panel (H-100/R-series: 15 Amp ATO fuse).
- Connect battery cables; attach negative cable last.
- Close 120VAC circuit breaker to the battery charger.
- Insert the fuse into the control panel.
- Move AUTO/OFF/MANUAL switch to MANUAL; engine should crank and start.
- Check voltage at generator terminals and check for leaks.
- Close generator main line circuit breaker; turn generator set off.
Preparation for Start-Up / Start-Up Checklist installation
⚠ Do not crank the engine continuously for longer than 30 seconds or the starter motor may be damaged.
Tools: manometer
- Ensure the 120VAC circuit breaker to the battery charger is open.
- Remove the 15 Amp ATO fuse from the control panel (H-100 and R-100: lower left-hand corner of control box).
- Connect the battery cables to the battery; attach negative cable last.
- Close the 120VAC circuit breaker to the battery charger.
- Measure the voltage at the battery before and after the charger is turned on.
- Verify all AC electrical connections are tight at the circuit breaker and transfer switch.
- Visually inspect entire area for loose paper, plastic wrappings, leaves, etc.
- Check all hose clamps and fittings for leaks or damage.
- Check all electrical plugs; ensure each is seated correctly.
- Verify the AUTO/OFF/MANUAL switch is in OFF position.
- Open the valve to the engine fuel line and bleed the fuel system of air.
- Open the generator main line circuit breaker.
- Connect a manometer to the gas line and record static pressure.
- Insert the fuse into the control panel and move the AUTO/OFF/MANUAL switch to MANUAL; engine should crank and start.
Reconfigure the Fuel System (NG to LP) installation
⚠ Make sure fuel supply is of proper pressure and type for configuration.
⚠ Keep ports free from debris during reconfiguration.
Tools: Pipe sealant
- Turn the main gas supply off.
- Remove carburetor fuel hose from outlet Port 1 of demand regulator.
- Remove brass hose fitting from Port 1.
- Remove pipe plug from Port 2.
- Install brass hose fitting into Port 2.
- Install pipe plug into Port 1.
- Connect carburetor gas hose to brass fitting; tighten all clamps and plugs.
- Set the Dip switch inside the control panel to LP or NG position.
Battery Inspection and Maintenance maintenance
⚠ DO NOT use jumper cables and a booster battery to crank or start the generator engine.
⚠ Storage batteries give off explosive hydrogen gas.
⚠ Battery electrolyte fluid is an extremely caustic sulfuric acid solution.
Tools: automotive-type battery hydrometer
- Inspect the battery posts and cables for tightness and corrosion. Tighten and clean as necessary.
- Check battery fluid level of unsealed batteries; if necessary fill with DISTILLED WATER ONLY.
- Have the state of charge and condition checked with an automotive-type battery hydrometer.
Battery Maintenance maintenance
⚠ Do not use tap water in batteries.
⚠ Storage batteries give off explosive hydrogen gas.
⚠ Do not use jumper cables or a booster battery to crank the engine.
Tools: Automotive-type battery hydrometer
- Inspect battery posts and cables for tightness and corrosion; tighten and clean as necessary.
- Check battery fluid level of unsealed batteries; fill with DISTILLED WATER only if necessary.
- Have state of charge and condition checked with an automotive-type battery hydrometer.
Battery Replacement maintenance
⚠ Be sure the AUTO/OFF/MANUAL switch is set to the OFF position before connecting the battery cables.
⚠ Be sure the 120VAC power supply to the battery is turned OFF, or sparking may occur at the battery posts.
- When replacing batteries, use the same number and type of battery as follows: BCI Group No. 24F-6, 535 CCA at 0 deg. F.
- The BCI number should be located directly on the battery.
Changing Engine Oil maintenance
⚠ Never operate engine with oil below the dipstick ADD mark.
⚠ Do not overtighten the oil filter.
Tools: Suitable container, Clean, lint-free cloth
- Remove OIL DRAIN HOSE from its retaining clip.
- Loosen and remove OIL DRAIN HOSE CAP; drain oil completely into suitable container.
- Install and tighten OIL DRAIN HOSE CAP; re-install into retaining clip.
- Turn OIL FILTER counterclockwise and remove; dispose of old filter.
- Apply light coating of new engine oil to seal of new filter; install and tighten by hand only.
- Remove OIL FILL CAP; add recommended oil. Do not fill above dipstick FULL mark.
- Start engine and check for oil leaks.
Changing the Engine Air Cleaner maintenance
- Remove the air cleaner cover.
- Replace the air filter, making sure it is positioned properly.
- Reattach the cover.
Check Engine Oil Level maintenance
⚠ Any attempt to crank or start the engine before it has been properly serviced with the recommended oil may result in an engine failure.
- Remove oil dipstick and wipe dry with a clean, lint-free cloth.
- Install oil dipstick, then remove again.
- Oil should be between FULL and ADD marks.
- If below ADD mark, remove oil fill cap and add recommended oil to FULL mark.
- DO NOT FILL ABOVE THE "FULL" MARK.
Spark Plugs - Inspect and Set Gap maintenance
⚠ Do not blast the spark plugs to clean.
Tools: Wire feeler gauge, Wire brush, Commercial solvent
- Clean area around base of spark plugs to keep dirt out.
- Remove spark plugs and check condition; replace if worn or reuse questionable.
- Check gap with a wire feeler gauge; adjust by carefully bending ground electrode.
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Voltage reconnection
| Voltage | Phase | Connection | Leads | Notes |
|---|---|---|---|---|
| 120/208V | 3 | Stator power winding connections - 3-phase, 120/208V (6 Lead), "Y" configuration | 6 lead | Rated voltage L-L 208V; L-N 120V. |
| 120/208V | 3-phase | Y configuration (6 lead) | 6-lead (S1-S6; E1-E3) | Rated voltage between circuit breaker terminals E1-E2, E1-E3, E2-E3 is 208V; between each terminal and neutral point 00 is 120V |
| 120/240V | 1 | Four-lead, single-phase stator - voltage code "A" (240V, 1-phase, 60 Hz) | 4-lead | Rated voltage between each circuit breaker terminal is 240V; rated voltage between each circuit breaker terminal and the neutral point 00 is 120V. |
| 240V | 1-phase | Four-lead, single-phase stator (voltage code A) | 4-lead | Rated voltage between each circuit breaker terminal is 240V; between each terminal and neutral point 00 is 120V |
| 277/480V | 3 | Stator power winding connections - 3-phase, 277/480V (6 Lead), "Y" configuration | 6 lead | Rated voltage between circuit breaker terminals E1-E2, E1-E3 and E2-E3 is 480V; between each terminal and neutral point 00 is 277V. |
| 277/480V | 3-phase | Y configuration (6 lead) | 6-lead (S1-S6; E1-E3) | Rated voltage between circuit breaker terminals E1-E2, E1-E3, E2-E3 is 480V; between each terminal and neutral point 00 is 277V |
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Common questions
What is the power rating of the Generac QT 3.9L 40kW?
The Generac QT 3.9L 40kW is rated 40 kW standby.
What engine does the Generac QT 3.9L 40kW use?
The Generac QT 3.9L 40kW is powered by the Generac V-type engine.
What fuel type does the Generac QT 3.9L 40kW take?
The Generac QT 3.9L 40kW runs on Natural Gas, Propane Vapor.
What is the oil capacity of the Generac QT 3.9L 40kW?
The Generac V-type engine in the Generac QT 3.9L 40kW has an oil capacity of 3.8 liters.
What is the coolant capacity of the Generac QT 3.9L 40kW?
The Generac QT 3.9L 40kW cooling system holds 4 liters (1.1 US gallons) for the engine, per the manufacturer specification sheet.
What voltages is the Generac QT 3.9L 40kW available in?
The Generac QT 3.9L 40kW is offered in 120/240 V, 120/208 V, 277/480 V, 1-phase or 3-phase-phase.
What battery does the Generac QT 3.9L 40kW use?
The Generac QT 3.9L 40kW uses 12 Volts V each, 525 CCA, group 24F, per the manufacturer specification sheet.
What oil filter fits the Generac QT 3.9L 40kW?
The Generac QT 3.9L 40kW uses oil filter part number 0E7415.
What air filter fits the Generac QT 3.9L 40kW?
The Generac QT 3.9L 40kW uses air filter part number 0A4637.
Troubleshooting
7Fault codes
| Code | Meaning |
|---|---|
| Safety 001 | DANGER |
Symptoms & remedies
| Symptom | Cause | Remedy |
|---|---|---|
| Engine won’t crank. | 1. 15 amp fuse blown. 2. Loose or corroded or defective battery cables. 3. Defective starter contactor. 4. Defective starter motor. 5. Dead or Defective Battery. 6. 5 amp fuse blown. | 1. Replace fuse. 2. Tighten, clean or replace battery cables as necessary. 3. Replace contactor.* 4. Replace starter motor.* 5. Remove, change or replace battery. 6. Replace fuse.* |
| Engine cranks but won't start | 1. Out of fuel. 2. Fuel solenoid (FS) is defective 3. Open Wire #14A from Engine Control circuit board. 4. Spark plugs defective. 5. Door on tank not closed. | 1. Replenish fuel. 2. Replace solenoid.* 3. Reconnect wire. 4. Clean, regap or replace plugs. 5. Close door on tank. |
| Engine starts hard, runs rough. | 1. Flame arrestor (air cleaner) plugged or damaged. 2. Plugged fuel line. 3. Defective spark plugs. 4. Fuel pressure incorrect. | 1. Clean or replace as needed. 2. Unclog fuel line. 3. Clean, regap or replace plugs. 4. Confirm fuel pressure to regulator is as recommended in SPECIFICATIONS. |
| Engine starts then shuts down. | AUTO/OFF/MANUAL Switch at OFF, engine continues to run | *Contact the nearest Authorized Dealer for assistance. |
| No AC output from generator. | Defective Control Module circuit board | *Contact the nearest Authorized Dealer for assistance. |
| Defective AUTO/OFF/MANUAL switch. | 1. Open/disconnected wire #15A between AUTO/OFF/MANUAL switch and Control Module circuit board. | Replace switch.* Reconnect/close wire. |
Fault codes and symptom→remedy steps extracted from this model’s service/owner documentation; verify against the official manual before servicing.
Repair guides
15- Battery Inspection and Maintenance
- Battery Maintenance
- Changing Engine Oil
- Changing Engine Oil
- Changing the Engine Air Cleaner
- Changing the Engine Air Cleaner
- Check Engine Oil Level
- Engine Start-up and Transfer (Manual Transfer Switch)
- Preparation for Start-Up
- Preparation for Start-Up / Start-Up Checklist
- Reconfigure the Fuel System (NG to LP)
- Reconfiguring the Fuel System (NG to LP)
- Retransfer and Shutdown
- Spark Plugs - Inspect and Set Gap
- Spark Plugs - Inspection and Gap Adjustment
Step-by-step procedures compiled from the Generac service manual for this model.
Parts
250| Part # | Description | Qty | System | |
|---|---|---|---|---|
| 027175 | LUBE GREASE SAE #90 80W90 (NOT SHOWN) | .200 GAL | Fluid | eBay |
| 029032 | HOSE 9/32 ID (43"LG) | 1 | Hose | Amazon eBay |
| 035606 | SENSOR HI COOLANT SHUTDOWN | 1 | Sensor | Amazon eBay |
| 035685 | CLAMP HOSE #28 1.32-2.25 | 2 | Hose | Amazon eBay |
| 040105 | HOSE COOL 2 IN ID 20R4 | 1 | Hose | Amazon eBay |
| 042561 | CLAMP HOSE #36 1.88-2.75 | 2 | Hose | Amazon eBay |
| 044149 | GASKET EXHAUST RING | 1 | Gasket | Amazon eBay |
| 047290 | HOSE 3/8 ID SINGLE BRAID (16” LG) | 1 | Hose | Amazon eBay $10.00 |
| 048031C | CLAMP HOSE BAND 1/4 | 2 | Hose | Amazon eBay $1.00 |
| 048031J | CLAMP HOSE BAND .63 | 1 | Hose | Amazon eBay |
| 052223 | HOSE 1/2 ID SAE-30R2 FUEL/OIL (14"LG) | 1 | Hose | eBay |
| 057822 | CLAMP HOSE #8 .53-1.00 | 2 | Hose | Amazon eBay |
| 057823 | CLAMP HOSE #10 .56-1.06 | 2 | Hose | Amazon eBay |
| 057824 | CLAMP HOSE #16 .87 - 1.50 | 1 | Hose | Amazon eBay |
| 059057 | HOSE 3/4 ID SAE-30R2 | 1 | Hose | Amazon eBay |
| 059193C | HOSE 5/8 ID X 31.0" LG | 1 | Hose | Amazon eBay |
| 059194 | HOSE 5/8 ID LPG & NG (24" LG) | 1 | Hose | Amazon eBay $12.00 |
| 064945 | GASKET CARB ADAPTOR | 1 | Gasket | Amazon eBay |
| 065386 | HOSE COOL 5/8 ID 100R6 (15"LG) | 1 | Hose | eBay |
| 067680 | ASSY VOLTAGE REGULATOR 60HZ | 1 | Avr | Amazon eBay $245.48 NAPA $19.32 |
| 069860E | HOSE DRAIN ASSY 28" | 1 | Hose | Amazon eBay |
| 077879 | HOSE VACUUM 5/32 | 1 | Hose | buy |
| 095613 | SEAL OIL | 1 | Seal | eBay |
| 095971 | SEAL OIL | 1 | Seal | eBay |
| 0A4637 | Air Cleaner | 1 | Air filter | Amazon eBay $49.95 NAPA $13.61 |
| 0A6283 | HOSE PREFORMED BLOCK HEATER | 1 | Hose | eBay |
| 0A6751 | SW-TMP 245 DEG 3/8 NPT | 1 | Sensor | Amazon eBay $49.75 |
| 0A6765 | RING GASKET 2.5 DIA | 2 | Gasket | eBay |
| 0A8584 | Switch | 1 | Sensor | Amazon eBay $19.57 FridayParts $31.60 |
| 0C7649 | CLAMP HOSE .38-.87 | 1 | Hose | Amazon eBay |
| 0C8127 | ELEMENT AIR CLEANER | 1 | Air filter | Amazon eBay $15.99 NAPA $24.03 FridayParts $21.87 |
| 0D2244M | ASSY MAGPICKUP (3/8-24 MALE) | 1 | Sensor | Amazon eBay $127.65 FridayParts $18.08 |
| 0D2698 | GASKET ADAPTER THROT BODY | 1 | Gasket | eBay |
| 0D3488 | BELT SERPENTINE (67.16" LG) (3000 RPM) | 1 | Belt | Amazon eBay $55.43 |
| 0D3488B | BELT SERPENTINE 40.85" LG (3600 RPM) | 1 | Belt | Amazon eBay $48.54 |
| 0D3488F | BELT SERPENTINE 38.35" LG (1800 RPM) | 1 | Belt | Amazon eBay |
| 0D3488G | BELT SERPENTINE (65.0" LG) (1800 RPM) | 1 | Belt | Amazon eBay $65.54 |
| 0D3488H | SERPENTINE BELT (60.5") | 1 | Belt | Amazon eBay $49.99 |
| 0D3488J | BELT SERPENTINE (65.3" LG) (2300 RPM) | 1 | Belt | Amazon eBay $50.38 |
| 0D3488K | SERPENTINE BELT (68.3" LG) (3600 RPM) | 1 | Belt | Amazon eBay $47.35 |
| 0D3488R | BELT SERPENTINE 54.72" | 1 | Belt | eBay |
| 0D4255 | GASKET EXHAUST MANIFOLD | 2 | Gasket | Amazon eBay |
| 0D5418 | STARTER MOTOR FORD V-10 ENGINE | 1 | Starter | Amazon eBay FridayParts $160.99 |
| 0D5419 | OIL FILTER, FORD V-10 ENGINE | 1 | Oil filter | Amazon eBay $16.80 NAPA $9.09 |
| 0D8030 | TENSIONER ENG. AUTOMATIC BELT | 1 | Belt | eBay $242.00 |
| 0E0502 | TEMPERATURE SENDER DELPHI | 1 | Sensor | Amazon eBay $39.79 |
| 0E0561 | ASSY WATER LEVEL SENSOR C/E PL | 1 | Sensor | Amazon eBay |
| 0E0992B | PLUG EXPANSION 21/32" O.D. (WATER PUMP) | Pump | Amazon eBay | |
| 0E2507 | PROBE COOLANT LEVEL 3/8 NPTF | 1 | Sensor | Amazon eBay $90.00 FridayParts $16.24 |
| 0E4390 | GASKET GOVERNOR ACTUATOR | 1 | Gasket | eBay $417.99 |
| 0E5968 | GASKET EXTRUDED TRIM (328” LG) | 1 | Gasket | Amazon eBay $26.58 |
| 0E6586 | GASKET BOSCH 32 & 40 | 1 | Gasket | Amazon eBay $385.00 |
| 0E6729 | STARTER 12V | 1 | Starter | Amazon eBay $145.00 NAPA $154.59 |
| 0E7080 | OIL FILTER 3.0L FORD | 1 | Oil filter | Amazon eBay $30.00 NAPA $12.22 KuduParts $13.00 FridayParts $15.00 |
| 0E7121 | O-RING 47.625 ID X 2.38 WIDTH | 1 | Seal | Amazon eBay |
| 0E7163 | GASKET EXHAUST 3.0L FORD | 2 | Gasket | eBay |
| 0E7415 | Oil Filter | 1 | Oil filter | Amazon eBay $81.99 NAPA $3.59 |
| 0E7702 | HOLD DOWN AIR CLEANER | 1 | Air filter | Amazon eBay |
| 0E7841 | GASKET THERMOSTAT ADAPTOR | 2 | Gasket | Amazon eBay $4.26 |
| 0E9868A | ALTERNATOR DC W/OUT PULLEY | 1 | Alternator | Amazon eBay $467.90 |
| 0F2097 | GASKET 390 GEARBOX | 1 | Gasket | eBay |
| 0F2256 | ASSY PCB PWR AVR W/AMP HEADER | 1 | Avr | eBay $200.00 |
| 0F2686 | HOSE RADIATOR UPPER CPL | 1 | Hose | Amazon eBay $65.00 |
| 0F2843 | GASKET THERMOSTAT HOUSING G3 | 1 | Gasket | Amazon eBay |
| 0F3158 | OIL COOLER FORD (150KW 3600RPM) | 1 | Oil cooler | eBay |
| 0F3216 | PULLEY 80 OD DC ALTERNATOR (1800 RPM) | 1 | Pulley | Amazon eBay |
| 0F3216C | PULLEY 132 OD DC ALTERNATOR (3000 RPM) | 1 | Pulley | Amazon eBay |
| 0F3228 | HOSE LOWER RAD CPL C2 3.0L | 1 | Hose | eBay |
| 0F3446 | BRKT R/H SIDE D.C. ALTERNATOR | 1 | Alternator | Amazon eBay |
| 0F3447 | BRKT L/H SIDE D.C. ALTERNATOR | 1 | Alternator | Amazon eBay |
| 0F3869 | SWITCH PRESSURE GAS 5" RISE (INCLUDED WITH I/N 3 REGULATOR ASSEMBLY) | 1 | Sensor | Amazon eBay $74.99 |
| 0F4269 | GASKET MIXER BODY | 1 | Gasket | Amazon eBay |
| 0F4301 | HOSE OIL COOLER (150KW 3600RPM) | 1 | Hose | eBay |
| 0F4413 | HOSE UPPER RAD CPL C2 3.9L | 1 | Hose | Amazon eBay |
| 0F4414 | HOSE LOWER RAD CPL C2 3.9L | 1 | Hose | Amazon eBay |
| 0F4612 | SENDER OIL PRESSURE 1/8" NPT | 1 | Sensor | Amazon eBay $189.99 |
| 0F5253 | V-BELT 31/64" X 61-3/8" (5.4L 100KW ONLY) | 1 | Belt | Amazon eBay |
| 0F5254 | V-BELT 31/64" X 62-3/8" | 1 | Belt | Amazon eBay |
| 0F5418 | ELEMENT AIR FILTER | 1 | Air filter | Amazon eBay $38.60 NAPA $13.61 |
| 0F5419 | ELEMENT AIR FILTER | 1 | Air filter | Amazon eBay $26.99 NAPA $11.24 |
| 0F5463 | HOSE LOWER RAD CPL C5 6.8L | 1 | Hose | Amazon eBay $24.85 |
| 0F6145 | SEAL WEATHER .45"DIA | A/R | Seal | Amazon eBay |
| 0F6305 | SEAL COVER 3.18 X 12.7 X 382 | 2 | Seal | Amazon eBay |
| 0F6305A | SEAL COVER 3.18 X 12.7 X 283 | 1 | Seal | Amazon eBay |
| 0F6322 | BOTTOM PLATE, AIR CLEANER 3.9L | 1 | Air filter | Amazon eBay |
| 0F6323 | PLATE, AIR CLEANER TOP 3.9L | 1 | Air filter | Amazon eBay |
| 0F6355 | GASKET SEAL PLATE 390 GB | 1 | Gasket | eBay |
| 0F6477 | ENHANCER GEAR OIL (NOT SHOWN) | .050 GAL | Fluid | eBay |
| 0F6480 | BRKT L/H SIDE DC ALTERNATOR | 1 | Alternator | Amazon eBay |
| 0F6631 | HOSE RADIATOR ENGINE | 1 | Hose | eBay |
| 0F6761 | HOSE UPPER RAD CPL C2 3.0L | 1 | Hose | eBay |
| 0F7077 | V-BELT 1/2" X 63-3/8" (6.8L, 100KW & 130KW) | 1 | Belt | Amazon eBay $49.95 |
| 0F7874 | ASSY BRUSH HOLDER 390/HSB | 1 | Brush | Amazon eBay $79.99 |
| 0F9071 | SENSOR OXYGEN | 1 | Sensor | buy |
| 0G0321 | HOSE COOL 5/8" ID 250#WP (14") | 1 | Hose | Amazon eBay |
| 0G0866 | HOSE OIL COOLER PREFORMED 3/4 (150KW 3600RPM) | 1 | Hose | eBay |
| 0G3167 | O-RING 2-3/4 X 3/32 X 2-15/16 | 2 | Seal | Amazon eBay |
| 0G5511 | GASKET THERMOSTAT 4.2L | 2 | Gasket | Amazon eBay |
| 0G5515B | ADAPTER THERMOSTAT 4.6L G3 | 1 | Thermostat | buy |
| 0H1827 | PROBE COOLANT LEVEL 3/8-18NPTF | 1 | Sensor | Amazon eBay |
| 0H3908 | HOSE RADIATOR LOWER C5 CPL | 1 | Hose | buy |
| 0H3909 | HOSE RADIATOR UPPER C5 CPL | 1 | Hose | buy |
| 0H4787 | SPARK PLUG | 1 | Spark plug | eBay |
| RC12LC4 | Spark Plug Champion # RC12LC4 | Spark plug | Amazon eBay $26.61 | |
| 022097 | WASHER LOCK M6-1/4 | 1 | Service part / kit | Amazon eBay $2.99 |
| 022127 | NUT HEX 1/4-20 STEEL | 1 | Service part / kit | Amazon eBay |
| 022129 | WASHER LOCK M8-5/16 | 4 | Service part / kit | Amazon eBay |
| 022152 | WASHER LOCK #10 | 1 | Service part / kit | Amazon eBay $12.00 |
| 022155 | WASHER LOCK #6 | 6 | Service part / kit | Amazon eBay |
| 022158 | NUT HEX #10-32 STEEL | 5 | Service part / kit | Amazon eBay |
| 022237 | WASHER LOCK 3/8 | 1 | Service part / kit | Amazon eBay |
| 022241 | NUT HEX 3/8-16 STEEL | 1 | Service part / kit | Amazon eBay |
| 022264 | WASHER LOCK #8-M4 | 2 | Service part / kit | Amazon eBay |
| 022447 | WASHER SHAKEPROOF INT 1/4 | 1 | Service part / kit | Amazon eBay |
| 022473 | WASHER FLAT 1/4-M6 ZINC | 1 | Service part / kit | Amazon eBay |
| 023454 | KEY WOODRUFF #E | 1 | Service part / kit | Amazon eBay |
| 023484N | BUSHING SNAP SB-2.5-31 | 1 | Service part / kit | Amazon eBay |
| 023897 | WASHER FLAT #10 ZINC | 4 | Service part / kit | Amazon eBay |
| 024114 | NUT HEX 5/16-24 STEEL | 1 | Service part / kit | Amazon eBay |
| 024469 | SCREW HHTT #10-32 X 3/8 CZ | 1 | Service part / kit | Amazon eBay |
| 025433 | LUG SLDLSS #6-14 X 13/64 CU | 1 | Service part / kit | Amazon eBay |
| 026812 | ELBOW 90D 3/4 NPT | 2 | Service part / kit | Amazon eBay |
| 026847 | BREATHER | 1 | Service part / kit | eBay |
| 026915 | NIPPLE CLOSE 3/4 X 1.375 | 2 | Service part / kit | Amazon eBay |
| 026925 | PLUG STD PIPE 3/8 STEEL SQ HD | 1 | Service part / kit | Amazon eBay |
| 029289 | TAPE ELEC 1/2 FOAM (AS REQ’D) | 1 | Service part / kit | Amazon eBay |
| 029673 | DIO BRIDGE 25A 600V | 1 | Service part / kit | Amazon eBay $22.99 |
| 031919 | PLUG STD PIPE 3/8 COUNTERSUNK | 1 | Service part / kit | Amazon eBay |
| 036797 | BOLT U 5/16-18 X 2.25 | 1 | Service part / kit | Amazon eBay |
| 036943 | SCREW PPHM #10/32 X 2 | 2 | Service part / kit | Amazon eBay |
| 037561 | NUT WING 1/4-20 NYLK | 1 | Service part / kit | Amazon eBay |
| 038804Y | CABLE BATT RED #1 X 35.00 | 1 | Service part / kit | Amazon eBay |
| 038805H | CABLE BATT BLK #1 X 23.00 | 1 | Service part / kit | Amazon eBay |
| 040532 | CB 0100A 3P 240V S BQ3 LL | 1 | Service part / kit | Amazon eBay |
| 042568 | SCREW HHC M6-1.0 X 20 G8.8 | 2 | Service part / kit | Amazon eBay |
| 043180 | WASHER FLAT M4 | 2 | Service part / kit | Amazon eBay |
| 043790 | BARBED EL 90 3/8 NPT X 3/8 | 1 | Service part / kit | Amazon eBay |
| 044118 | BARBED STR 1/2 NPT X 5/8 | 1 | Service part / kit | Amazon eBay |
| 04576100AQ | STUD M14-2.0 X 615 G5 ZINC | 4 | Service part / kit | Amazon eBay $13.66 |
| 04576100BU | STUD M14-2.0 570 G5 ZINC | 4 | Service part / kit | Amazon eBay |
| 046627 | CAP RADIATOR | 1 | Service part / kit | Amazon eBay $15.00 |
| 047248 | BALL BEARING-45 MM | 1 | Service part / kit | Amazon eBay |
| 047411 | SCREW HHC M6-1.0 X 16 G8.8 | 4 | Service part / kit | Amazon eBay |
| 048467 | CIRCT BRK 7 X 1 ETA 46-500-P | 1 | Service part / kit | Amazon eBay |
| 049226 | WASHER LOCK M5 | 6 | Service part / kit | Amazon eBay |
| 049721 | SCREW HHC M6-1.0 X 35 G8.8 BLK | 1 | Service part / kit | Amazon eBay |
| 049813 | NUT HEX M6 X 1.0 G8 YEL CHR | 1 | Service part / kit | Amazon eBay $3.99 |
| 050279 | DECAL FUEL INLET NG (NATURAL GAS APPLICATION) | 1 | Service part / kit | Amazon eBay |
| 050280 | DECAL FUEL INLET LPG (LP VAPOR APPLICATION) | 1 | Service part / kit | Amazon eBay |
| 050331 | BATTERY POST COVER BLACK | 1 | Service part / kit | Amazon eBay |
| 050331A | BATTERY POST COVER RED + | 1 | Service part / kit | Amazon eBay |
| 050873A | PLUG PIPE 1/4 CSK W/ VIBRA SL | Service part / kit | Amazon eBay | |
| 051713 | WASHER FLAT M5 | 2 | Service part / kit | Amazon eBay |
| 052250 | TAPE FOAM 1 X 1 (26.75” LG) | 2 | Service part / kit | Amazon eBay FridayParts $16.89 |
| 052251 | DAMPENER VIBRATION 40 BLUE | 4 | Service part / kit | Amazon eBay |
| 052252 | DAMPENER VIBRATION | 4 | Service part / kit | Amazon eBay $19.28 |
| 052257 | SPACER .49 X .62 X 1.87 PWDR/ZNC | 4 | Service part / kit | Amazon eBay |
| 052624 | BEARING BALL 6212 SEALED | 1 | Service part / kit | Amazon eBay $15.38 |
| 052677 | WASHER NYLON .50 X .87 X .06 | 1 | Service part / kit | Amazon eBay |
| 052860 | NUT FLANGED HEX M12-1.75 | 4 | Service part / kit | Amazon eBay |
| 0536210410 | ASSY WIRE 14.00" | 1 | Service part / kit | Amazon eBay |
| 054455 | ADP OIL DRN 1/2-20 | 1 | Service part / kit | Amazon eBay |
| 055414 | LUG SLDLSS #2-#8 X 17/64 CU | 1 | Service part / kit | Amazon eBay |
| 055596 | BARBED STR 3/8 NPT X 3/8 | 1 | Service part / kit | Amazon eBay |
| 055911 | BLOCK TERM 20A 12 X 6 X 1100V | 1 | Service part / kit | Amazon eBay |
| 055934D | CLAMP VINYL 1.06 X .406 Z | 1 | Service part / kit | Amazon eBay $3.99 |
| 056739 | RELAY SOLENOID 12VDC PNL MNT | 1 | Service part / kit | Amazon eBay |
| 057019 | BALL BRG 65 X 120 X 23 | 2 | Service part / kit | eBay |
| 057019S | BEARING #6213 SEALED | 1 | Service part / kit | eBay |
| 057073 | JUNCTION BLOCK 3/8-16 | 2 | Service part / kit | Amazon eBay |
| 057701 | BLOCK TERM 20A 8 X 6 X 1100V | 1 | Service part / kit | Amazon eBay |
| 057795A | BARBED EL 90 3/4 PLASTIC | 1 | Service part / kit | Amazon eBay |
| 057796 | GROMMET | 1 | Service part / kit | Amazon eBay |
| 058208 | BATT 12VDC 24F 625 | 1 | Service part / kit | Amazon eBay |
| 058665 | BATTERY 12VDC 90-AH 27F | 1 | Service part / kit | Amazon eBay |
| 061012 | PLUG STD PIPE 1/8 SOCKET HEAD | 1 | Service part / kit | Amazon eBay |
| 065852 | SPRING CLIP HOLDER .37-.62 | 1 | Service part / kit | Amazon eBay |
| 066760 | STRIP SEALANT 1/8 X 1 (44.52”LG) | 1 | Service part / kit | Amazon eBay |
| 067210A | DECAL GROUND LUG | 1 | Service part / kit | Amazon eBay |
| 067377 | Start-up Inspection for Standby Power Systems | Service part / kit | Amazon eBay | |
| 068405C | EXITER FIELD 2" LG SPD CONN | 1 | Service part / kit | eBay |
| 069811 | CAP HEX 1/4 NPT BRASS | 1 | Service part / kit | Amazon eBay |
| 070892 | SLIP RING MACHINED | 1 | Service part / kit | Amazon eBay |
| 075580 | FLANGE FUEL INLET | 1 | Service part / kit | Amazon eBay |
| 075763 | BOOT BATTERY CABLE | 1 | Service part / kit | Amazon eBay |
| 076749 | TANK COOLANT RECOVERY | 1 | Service part / kit | Amazon eBay |
| 077043F | CONDUIT FLEX 1-1/4" (30" LG - 3.0L FORD & 3.9L CHRYSLER) | 1 | Service part / kit | Amazon eBay |
| 077043J | CONDUIT FLEX 2.0" ID (36” LG) | 1 | Service part / kit | Amazon eBay |
| 077992 | NUT HEX LOCK M6-1.0 SS NY INS | 21 | Service part / kit | Amazon eBay |
| 078115 | WASHER SELF LOCKING DOME #4-40 | 26 | Service part / kit | Amazon eBay |
| 078115A | WASHER SELF LOCKING DOME #8-32 | 6 | Service part / kit | Amazon eBay $2.74 |
| 080712 | BRKT COOLANT RECOVERY TANK | 1 | Service part / kit | Amazon eBay |
| 080762 | BOLT U 3/8-16 X 2.62 | 1 | Service part / kit | Amazon eBay |
| 081008 | GROMMET 1.25 X .25 X .75 | 1 | Service part / kit | Amazon eBay |
| 082573 | SWITCH RKR DPST 125V SPD | 1 | Service part / kit | Amazon eBay |
| 085917 | WASHER LOCK 3/8 SS | 2 | Service part / kit | Amazon eBay |
| 085918 | NUT HEX 3/8-16 SSTL | 1 | Service part / kit | Amazon eBay |
| 087233 | RIVET POP .1875 X .450 SS | 2 | Service part / kit | Amazon eBay |
| 087272 | ASSY EXCITER 2.00" STK | 1 | Service part / kit | eBay |
| 088775 | WASHER FLAT 3/8 SS | 2 | Service part / kit | Amazon eBay |
| 089514 | FTG CMPR 3/8TUBE X 3/8 NPT W/FERL | 1 | Service part / kit | Amazon eBay |
| 089685 | GROMMET .75 X .12 X .50 | 1 | Service part / kit | Amazon eBay |
| 089961 | FOAM STRIP 3/4"WIDE X 3/16"THK (294”LG) | 1 | Service part / kit | Amazon eBay |
| 090152 | ASSY BRIDGE RECTIFIER | 1 | Service part / kit | eBay |
| 090283 | CAP RADIATOR 13 PSI | 1 | Service part / kit | Amazon eBay $19.99 |
| 0912970094 | ASSY WIRE 14 AWG 34.8" GRN/YEL | 2 | Service part / kit | Amazon eBay |
| 0A1786 | RETAINING COMPOUND | 2.5cc | Service part / kit | eBay |
| 0A2077 | CB 0125A 2P 240V S BQ2 LL | 1 | Service part / kit | Amazon eBay $70.00 |
| 0A4121 | VALVE PCV | 1 | Service part / kit | Amazon eBay |
| 0A5062J | SPACER 9.5H 3.2 ID | 4 | Service part / kit | Amazon eBay $3.36 |
| 0A7822 | LUG SLDLSS 600/250-1/0 X 1/4-28 | 1 | Service part / kit | Amazon eBay $24.99 |
| 0A9457 | DECAL NEUTRAL | 1 | Service part / kit | Amazon eBay |
| 0C2266 | SCREW PHTT M5-0.8 X 16 ZYC | 6 | Service part / kit | Amazon eBay |
| 0C2428 | SCREW PHTT #6-32 X 1/2 ZYC | 6 | Service part / kit | Amazon eBay |
| 0C2454 | SCREW THF M6-1 X 16 N WA Z/JS | 11 | Service part / kit | Amazon eBay $17.00 |
| 0C2634A | ASSEMBLY COVER ACCESS | 1 | Service part / kit | Amazon eBay |
| 0C3397 | FASTENER RATCHET | 4 | Service part / kit | Amazon eBay |
| 0C3990 | SCREW PHTT M4-0.7 X 10 ZYC | 2 | Service part / kit | Amazon eBay |
| 0C9708 | INSTR HYPOT TEST (NOT SHOWN) | REF | Service part / kit | Amazon eBay |
| 0D1509 | DECAL INLET PRESSURE | 1 | Service part / kit | Amazon eBay |
| 0D4698 | BLOCK TERM 20A 6 X 3 X 1100V | REF | Service part / kit | Amazon eBay |
| 0D5466 | BUS BAR NEUTRAL BLOCK 390 | REF | Service part / kit | Amazon eBay |
| 0D5552 | CB 0050A 3P 480V S ED4 LL | 1 | Service part / kit | Amazon eBay |
| 0D5553 | CB 0060A 3P 480V S ED4 LL | REF | Service part / kit | Amazon eBay |
| 0D5554 | CB 0070A 3P 480V S ED4 LL | REF | Service part / kit | Amazon eBay |
| 0D5556 | CB 0090A 3P 480V S ED4 LL | 1 | Service part / kit | Amazon eBay $449.00 |
| 0D5572 | CB 0150A 3P 600V S FD6 LL | 1 | Service part / kit | Amazon eBay |
| 0D5573 | CB 0175A 3P 600V S FD6 LL | REF | Service part / kit | Amazon eBay |
| 0D5574 | CB 0200A 3P 600V S FD6 LL | REF | Service part / kit | Amazon eBay |
| 0D5575 | CB 0225A 3P 600V S FD6 LL | REF | Service part / kit | Amazon eBay |
| 0D5576 | CB 0250A 3P 600V S FD6 LL | REF | Service part / kit | Amazon eBay |
| 0D5577 | CB 0300A 3P 600V S JD6 LL | 1 | Service part / kit | Amazon eBay |
| 0D6029 | SCREW HHTT M6-1.0 X 16 ZYC | 4 | Service part / kit | Amazon eBay $29.48 |
| 0D7177V | DIODE BRIDGE 1P 35A 1000V | 2 | Service part / kit | buy |
| 0D7178T | Control Panel Fuse | 1 | Service part / kit | Amazon eBay $26.44 |
| 0D9693 | CB 0125A 3P 480V S ED4 LL | 1 | Service part / kit | Amazon eBay |
| 0D9832 | SCREW HHC M12-1.75 X 75 SS | 4 | Service part / kit | Amazon eBay |
| 0E0170B | EXHAUST BLANKET 850MM (C4) | 1 | Service part / kit | Amazon eBay |
| 0E0170C | EXHAUST BLANKET 725MM (C4) | 1 | Service part / kit | Amazon eBay |
| 0E0992A | PLUG EXPANSION 14 OD | 10 | Service part / kit | Amazon eBay |
| 0E3161 | ASSY PCB BOSCH GOV DRIVER | 1 | Service part / kit | Amazon eBay $124.95 |
| 0E3257 | SCREW HWHTF M6-1.0 X 16 | 4 | Service part / kit | Amazon eBay |
| 0E3664 | BASE, QN CIRCUIT BREAKER | 1 | Service part / kit | Amazon eBay |
| 0E4392 | ACTUATOR BOSCH 60 GOVERNOR | 1 | Service part / kit | eBay $417.99 |
| 0E4394 | ACTUATOR BOSCH 40 GOVERNOR | 1 | Service part / kit | Amazon eBay $416.99 |
| 0E4395 | ACTUATOR BOSCH 32 GOVERNOR | 1 | Service part / kit | Amazon eBay $385.00 |
| 0E4494 | SWITCH RKR DPDT ON-OFF-ON | 1 | Service part / kit | Amazon eBay $8.99 |
| 0E5048A | FLEXPLATE HSB 3.9L CHRYSLER (1800RPM) | 1 | Service part / kit | Amazon eBay |
| 0E5706 | REAR BEARING CARRIER 390/DRCT | 1 | Service part / kit | Amazon eBay |
| 0E6002 | MTG TRACK BQ SIEMENS CB 3P | 1 | Service part / kit | Amazon eBay |
Service, wear & replacement parts referenced for this model and its engine — confirm the exact part for your serial number. See the full parts catalog to search and cross-reference.
Available documents
Owner's manual — 0F3459 (Generac)Owner's manual — 5222.pdf (Generac)
This page was generated from the 2 manufacturer documents above by automated extraction; every figure shown is copied from one of them. How the data is compiled.