Home›Engines›Cummins/Onan KTA19

Cummins/Onan KTA19 Engine

The Cummins/Onan KTA19 is a 18.7 L engine rated at 1800 rpm. It powers generator sets from Cummins/Onan, including the DFE. It holds 45 L (11.9 gal) of oil and 91 L (24.0 gal) of coolant.

Also known as: Cummins KTA19

Part of the Cummins/Onan KTA19 engine family — 8 variants share parts & fitment.

18.7 L

Displacement

1800 rpm

Rated speed

45.0 L

Oil capacity

On this pageSpecs Generator sets Maintenance FAQ Service intervals Torque & specs Fluids Fault codes Procedures Wiring

Engine specifications

Oil capacity	45.0 L
Coolant capacity	91.0 L
Displacement	18.7 L
Rated speed	1800 rpm

Generator sets powered by this engine

Cummins/Onan DFE

How to read your Cummins/Onan engine serial & model number →

Troubleshooting

Fault codes

Code	Meaning
soul	G

Fault codes and symptom→remedy steps extracted from this engine’s service/owner documentation; verify against the official manual before servicing.

Common problems

Over Current 1471
Low AC Voltage 2331
High AC Voltage 2358
Weak Battery 1442
Warning, Shutdown, and Non-Automatic lamps are not lit. Digital display shows main menu or selected menu.
Cause: Indicates all engine systems are normal. No corrective action required
Warning Status Indicator: This yellow lamp is lit whenever the control detects a warning condition.
Fix: After the condition is corrected, warning indicators can be reset by pressing the Fault Acknowledge button. (It is not necessary to stop the generator set if the fault becomes inactive during genset operation.)
Warning lamp lights.
Cause: LOW COOLANT TEMP 210 – WARNING
Fix: Set is in standby mode but is not operating. Warning occurs when engine coolant temperature is 70° F (21° C) or lower. NOTE: In applications where the ambient temperature falls below 40°F (4°C), Low Engine Temp may be indicated even though the coolant heaters are operating.
Voltage on any phase has dropped below a preset value. 27
Under frequency shutdown (81 u) - Generator set output frequency cannot be maintained. 81 u
Under Frequency 1448
Too Long in Idle 2342
The light will display the fault codes (active or inactive) in succession, starting with the most recent. Up to 32 (unacknowledged) fault codes can be stored in control panel memory. 213
Speed/Hz Match 1469
Speed Signal Lost 121
Shutdown Status Indicator: This red lamp is lit whenever the control detects a shutdown condition. The generator set can not be started when this lamp is on.
Fix: After the condition is corrected, shutdown indicators can be reset by turning the 0/Manual/Auto switch to the 0 position, and pressing the Fault Acknowledge button.

Compiled from service & troubleshooting documentation across every generator set that uses the Cummins/Onan KTA19.

Maintenance schedule

Item	Spec	Capacity	Part #	Interval
Air filter	Clean with low pressure compressed air 30 psi (207 kPa) or soak 15 minutes in Donaldsons D1400 solvent; replace after two cleanings		L028-2	100 hr	eBay
Fuel filter	Drain 1 cup or more of fuel to remove water and sediment		—	100 hr
Battery			—	100 hr
Belt	Visually check for wear or slippage; replace if hard or brittle		—	100 hr
Coolant	24 Gal (90 L)	90.0 L	—	500 hr
Coolant filter			—	6 hr
Oil	12 Gal (45 L)	83.3 L	—	250 hr

Pooled from every document that names this exact engine — confirm the interval and part number against your unit's serial number.

Service intervals

Item	Action	Hours	Months	Notes
Air cleaner	Check	250 hr	6 mo	X1; replace as necessary; refer to QSX15 engine manual
All hardware (fittings, clamps, fasteners, etc.)	Check	100 hr		Daily or after 8 hours
Anti-freeze and DCA concentration	Check	250 hr	6 mo	X1; refer to QSX15 engine manual
Coolant heater(s)	Check	100 hr		Daily or after 8 hours
Drive belt	Check	250 hr	6 mo	X1; refer to Cummins QSX15 Series Engine Operation and Maintenance Manual for interval/procedure
Engine oil level	Check	8 hr		Daily or after 8 hours
Fuel filter(s)	Drain	250 hr	6 mo	X1; refer to QSX15 engine manual
Genset	Inspect	8 hr		Daily; check for oil, fuel, cooling and exhaust system leaks
Radiator hoses for wear and cracks	Check	250 hr		Daily or after 8 hours
Charge Air Piping	Check	50 hr		Weekly
Coolant heater	Check	50 hr		Weekly or after 50 hours
Coolant level	Check	50 hr		Weekly or after 50 hours
Exhaust condensate trap	Drain	100 hr		Drain water to prevent it flowing back into the engine
Fuel level	Check	50 hr		Weekly or after 50 hours
Oil level	Check	50 hr		Weekly or after 50 hours
Air cleaner	Clean	100 hr		Monthly or after 100 hours; clean if required, perform more often in dusty conditions
Battery charging system	Check	100 hr		Monthly or after 100 hours
Battery electrolyte level	Check	200 hr		Monthly or After 100 Hrs
Fuel tank water and sediment	Drain	100 hr		Monthly or after 100 hours
General set inspection	Inspect	100 hr		Monthly or after 100 hours (Table 5-1, footnote X2): check for oil, fuel, cooling and exhaust system leaks; check exhaust system audibly and visually with set running
Generator air outlet	Check	100 hr		Monthly or After 100 Hrs
Radiator hoses	Check	500 hr	12 mo	Monthly or After 100 Hrs; check for wear and cracks
Starting batteries	Check	100 hr		Check condition and terminals
Air Compressor Air Cleaner Element	Replace	250 hr	6 mo	Cummins two-cylinder only
Air cleaner	Replace	250 hr		Check air cleaner; replace as necessary. Refer to QSX15 manual.
Belt Tension	Check	250 hr	6 mo
Coolant Filter	Replace	250 hr	6 mo
Cooling Fan	Check	250 hr	6 mo
Cooling System Additives	Check	250 hr	6 mo
Crankcase Breather Tube/Hose	Clean	250 hr	6 mo
Crankcase oil and filter	Change	250 hr	12 mo	Prime power: every 6 months or 250 hours; standby: every 12 months or 250 hours, whichever comes first
Drive belt tension	Check	250 hr	6 mo	Visually check belt for wear or slippage; replace if hard or brittle
Engine oil and filter	Replace	250 hr	6 mo	X1; 6 Months or After 250 Hrs; refer to QSX15 engine manual
Fuel Filter(s)	Replace	250 hr	6 mo
Lubricating Oil and Oil Filter	Change	250 hr	6 mo	Generator drive: 250 hours or 12 months, whichever occurs first
Radiator Hoses	Inspect	250 hr	6 mo	Check for wear & cracks
Water coolant filter	Replace	250 hr	6 mo	X1; 6 Months or After 250 Hrs
Air cleaner element	Change	500 hr	12 mo	Yearly or after 500 hours; clean if required more often
Coolant filter	Change	500 hr	12 mo	Yearly or after 500 hours; refer to engine operation and maintenance manual
Cooling system	Clean	500 hr	12 mo	Yearly or after 500 hours; drain and replace coolant mixture

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Service specifications

Type	Item	Value	Unit	Condition
Clearance	Air compressor discharge carbon deposit	2	mm	clean if exceeds
Clearance	Angular alignment maximum T.I.R.	0.001	inch per inch of radius (center of shaft to indicator axis)	measuring deflection to bolt heads
Clearance	Crankshaft end clearance new maximum	0.43	mm
Clearance	Crankshaft end clearance new minimum	0.18	mm
Clearance	Crankshaft end clearance worn limit	0.56	mm
Clearance	Exhaust pipe clearance from combustible wall or partition	12	inches (305 mm)	minimum
Clearance	Exhaust pipe clearance to combustible wall/partition	12	inches (305 mm)
Clearance	Fan hub gear driven clearance	2.54	mm	less than indicates hub moved on retainer
Clearance	Float switch assembly float lift clearance below C-clip stop	1/8	inch (3 mm)	use a feeler gauge
Clearance	Fuel line clearance from electrical wiring	1/2	inch (12.7 mm)
Clearance	Fuel line clearance from hot exhaust parts	2	inch (51 mm)
Clearance	Generator mount pre-load steel spacer thickness	1 3/4	inch	two spacers under both stator foot brackets
Clearance	Generator-to-engine angular alignment (T.I.R.)	.001 in. per inch of radius (center of shaft to indicator axis), maximum	in	750 kW gensets and larger
Clearance	HVT Non-Top Stop injector travel adjustment	10.24	mm
Clearance	HVT Non-Top Stop injector travel limits	10.18 to 10.29	mm
Clearance	MPU installation gap adjustment	back out 1/4 turn after touching gear tooth	turn
Clearance	PTD Non-Top Stop injector travel adjustment	7.72	mm
Clearance	PTD Non-Top Stop injector travel limits	7.67 to 7.77	mm
Clearance	Rubber vibration damper rubber member	3	mm	replace if more than below metal surface
Clearance	STC Top Stop injector travel limit	10.18 to 10.29	mm	with high lift cam and injectors: 12.47 to 12.57 mm
Clearance	Turbocharger axial clearance HC5A maximum	0.13	mm
Clearance	Turbocharger axial clearance HC5A minimum	0.05	mm
Clearance	Turbocharger axial clearance T18A maximum	0.23	mm
Clearance	Turbocharger axial clearance T18A minimum	0.10	mm
Clearance	Vibration damper index marks alignment	1.5	mm	replace if more than out of alignment
Clearance	Vibration isolator base elevation difference	0.25	inch (6 mm)	shimmed or grouted within this of each other
Clearance	Vibration isolator clearance	0.25	inch (6 mm)
Clearance	Vibration isolator nominal clearance (leveling bolt)	0.25	inch (6 mm)	minimum, or greater
Gap	Coolant level below radiator cap lower sealing surface	3/4 inch (18 mm)	inch (mm)
Gap	MPU sensor to flywheel ring gear tooth	back it out one quarter turn	turn	sensor threaded in until it just touches gear tooth
Other	AVR Droop setting	5	% at full load, 0 PF
Other	AVR voltage regulation (load regulation)	approximately ±0.5	% RMS
Other	Ambient temperature below which coolant heaters recommended (NFPA 110)	40	°F
Other	Angular alignment maximum T.I.R.	.001 inches per inch of radius	in/in	center of shaft to indicator axis
Other	Battery CCA (minimum)	1400	CCA	Cold Soak @ 0° F (-18° C)
Other	Battery charging alternator output	35	Amps
Other	Battery specific gravity (fully charged)	1.26	specific gravity	at 80 F (27 C)
Other	Battery specific gravity (high ambient, above 95F/35C)	1.225		recommended to reduce electrolyte loss
Other	Battery specific gravity (recharge threshold)	below 1.260
Other	Battery specific gravity charge threshold	1.215	corrected	charge battery if reading below
Other	Battery specific gravity fully charged	1.260	corrected	add 0.004 per 10 F above 80 F (27 C)
Other	Battery specific gravity, fully charged	approximately 1.260	specific gravity	at 80 F (27 C)
Other	Battery terminal cleaning solution	1/4 pound baking soda to 1 quart water
Other	CAN datalink main trunk maximum length	40	meters	no more than 30 devices
Other	CAN datalink stub maximum length	1	meter	stub from main trunk to each module
Other	CAN datalink transmission speed	250	KBaud
Other	Charge battery if specific gravity below	1.215	specific gravity
Other	Compression ratio	17.0:1
Other	Frequency regulation	Isochronous
Other	Fuel lift height limit	6	feet	(1.8 meters) between fuel lift pump and bottom of dip tube
Other	Fully charged battery corrected specific gravity	1.260	specific gravity	corrected reading @ 80 F (27 C)
Other	GOV GAIN default value for paralleling applications	70	%
Other	Maximum cranking voltage drop	2	volts	difference between battery and starter terminals while cranking
Other	Mounting bolt size	5/8	inch or 16 mm
Other	Mounting bolts	5/8 inch or 16 mm	inch / mm	anchored mounting bolts
Other	Optional run/alarm relay contact rating	10 amps at 28 VDC or 120 VAC, 80%PF; 6 amps at 240 VAC, 80%PF; 3 amps at 480/600 VAC, 80%PF	amps
Other	Output frequency adjustment (PCC)	+/- 5	%	set running under normal parameters
Other	Over current warning threshold	110	% of rated
Other	Over/Under Frequency Sensor Module - Over Hz Set, 50 Hz nominal	55	Hz	reset 53 Hz
Other	Over/Under Frequency Sensor Module - Over Hz Set, 60 Hz nominal	65	Hz	reset 63 Hz

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Recommended fluids

Fluid	Grade	Standard	Ambient	Capacity	Notes
Coolant		Refer to Cummins QSX15 Series Engines Operation and Maintenance Manual for coolant recommendations/specifications		58.0 L	Cooling System (Capacity Std. Radiator) printed as 15.3 Gal (58 L); check anti-freeze and DCA concentration
Coolant	50 percent ethylene glycol / 50 percent water	ASTM D4985 low-silicate antifreeze			KT engine only 26 liters [28 U.S. qts]; KTA/KTTA engine only 30 liters [32 U.S. qts].
Coolant	Balanced coolant mixture of water and antifreeze	Refer to Cummins engine Operation and Maintenance Manual		90.0 L	Capacity with standard radiator 24 Gal (90 L); drain and replace mixture every year or after 500 hours; add until 3/4 inch (18 mm) below radiator cap lower sealing surface
Coolant	soft water / E.G. / DCA mixture				Cooling system to be filled with soft water/E.G./DCA mixture (on-site review checklist).
Engine oil		Refer to Cummins QSX15 Series Engines Operation and Maintenance Manual for lubricating oil classification/viscosity		58.0 L	Oil Cap. w/Filters printed as 26 Gallons (58 L); gense is shipped filled with correct type and quantity of oil
Engine oil	SAE 15W-40	API CE or CF4			Cummins Premium Blue or equivalent; CD or CD/SF where CE/CF4 unavailable; sulfated ash max 1.85 mass percent
Engine oil	SAE 5W-30 synthetic	API CE/SF	above -23°C		Arctic operation below -23°C
Fuel	ASTM D975 No. 2-D	Cetane number 40-50, 300-500 ppm Sulfur			Diesel fuel specifications
Fuel	ASTM No. 2 D diesel	ASTM No. 2 D			Below 0°C blends of No. 2 D and No. 1 D; viscosity must be kept above 1.3 cSt.
Fuel	ASTM No. 2 diesel				Cummins engines normally use ASTM No. 2 diesel fuel.
Fuel	Diesel				Day tank fuel transfer pump maintains reservoir of diesel fuel in the day tank.
Fuel	diesel				Refer to Cummins QSX15 Series Engines Operation and Maintenance Manual for fuel recommendations; do not use zinc coated or copper fuel lines with diesel fuel; keep fuel supply tanks as full as possible
Grease	Lithium based grease	Mobilux No. 2 or Shell Alvania R3		2.74 oz (81 ml)	Generator end bearing. Temperature range -22F to +248F (-30C to +120C). Grease should be equally divided between the bearing, bearing cap cavity, and bearing cartridge cavity.
Grease	Water pump type grease				Lubricate fan idler pivot arm assembly and front engine support.
Grease	Lithium based grease, Mobilux No. 2 or Shell Alvania R3		-30°C to 120°C	2.74 oz (81 ml)	End bearing lubricant; grease equally divided between bearing, bearing cap cavity and bearing cartridge cavity.
Other	Donaldsons D1400 solvent				Soak air cleaner filter element at least 15 minutes in water and D1400 solvent to remove soot, carbon and dirt

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Fault codes

Code	Name	Meaning	Severity	Action
101	IDLE MODE	Indicates that the engine is operating in idle mode. Grounding the engine idle input causes generator build-up to be inhibited and the engine to be governed at 800 RPM.	Warning	Remove ground from engine idle input to return to normal speed and voltage.
102	EMERGENCY STOP	Local or remote Emergency Stop; engine shuts down and will not crank	Shutdown	Turn the switch clockwise and allow it to pop out (local only); move the Run/Off/Auto switch to Off; press the Reset switch; select Run or Auto as required. Can be reset only at the PCC front panel.
111	Internal ECM error	Internal ECM error	Shutdown
1118		Prelube relay driver	Warning
112	Actuator not responding	Category A	Shutdown
1121		Failed to Disconnect	Warning
1122	Rated/Idle Trans		Info
1123	Shutdown After Battle Short	A shutdown fault occurred while Battle Short was enabled and Battle Short transitioned from enabled to disabled	Warning	Review the Fault History and perform corrective action
1124	Delayed Shutdown	Provides advanced warning of an impending generator set shutdown to loads which cannot handle sudden power loss	Warning	A shutdown fault is present; review fault history
113	Actuator sensor fault	Category B	Warning
1131	Battle Short Active	Battle short mode has been activated	Warning	Battle short function enabled
115	No speed signal	No speed signal	Shutdown
116	Time press sensor high	Time press sensor high	Shutdown
117	Time press sensor low	Time press sensor low	Shutdown
118	Pump press sensor high	Pump press sensor high	Warning
119	Pump press sensor low	Pump press sensor low	Warning
121	Speed Signal Lost	No engine speed signal	Warning
1219		Utility CB tripped	Warning
122	Manifold air press sensor	Manifold air press sensor	Warning
1222		Power transfer not in auto	Warning
1223		Utility frequency sensor	Warning
1224		Gen over voltage sensor	Warning
1225		Gen under voltage sensor	Warning
1226		genset frequency sensor	Warning
123	Manifold air press sensor	Manifold air press sensor	Warning
1245	CAN - Engine Shutdown	The PCC received a shutdown message from the ECM	Shutdown	Refer to the E-Controls service tool and the engine service manual
1246	CAN - Unknown Engine Fault	The PCC received an unknown message from the ECM	Warning	Refer to the E-Controls service tool and the engine service manual
1247	CAN - Engine Unannounced Fault	The PCC received an unknown message from the ECM	Warning	Refer to the E-Controls service tool and the engine service manual
1248	CAN - Engine Warning Fault	The PCC received an unknown message from the ECM	Warning	Refer to the E-Controls service tool and the engine service manual
1311	Customer input #1	Optional customer-selected fault, e.g. Low Fuel Day Tank, Water In Fuel, Ground Fault, Low Starting Hydraulic/Air Pressure		Programmable via service tool: enable/disable, status/warning/shutdown, active closed/open, custom display name
1311, 1312, 1317, 1318	Customer Input	Nature of the fault is an optional customer selection		Disconnect signal lead from TB1 (CUST_IN1 TB1-4, CUST_IN2 TB1-5, CUST_IN3 TB1-6, CUST_IN4 TB1-7) and reset the control; if the message clears, external wiring has a short/open or the active input selection (closed/open) is not correct
1312	Customer input #2	Optional customer-selected fault		Customer defined fault; message editable by the customer; can be programmed to initiate a shutdown or warning.
1313	Network Fault 1 thru 4	Network Fault 1		Customer defined fault; message editable by the customer; can be programmed to initiate a shutdown or warning.
1313-1316	Network Fault 1 Through 4	Indicates network input (#1-#4) is in an active state		Each fault function can be programmed (using the service tool) as Status, Warning, or Shutdown; change display name using up to 19 characters
1314	Network Fault 2	Network Fault 2		Customer defined fault; message editable by the customer; can be programmed to initiate a shutdown or warning.
1315	Network Fault 3	Network Fault 3		Customer defined fault; message editable by the customer; can be programmed to initiate a shutdown or warning.
1316	Network Fault 4	Network Fault 4		Customer defined fault; message editable by the customer; can be programmed to initiate a shutdown or warning.
1317	Customer input #3	Customer input #3		Customer defined fault; message editable by the customer; can be programmed to initiate a shutdown or warning.
1318	Customer input #4	Customer input #4		Customer defined fault; message editable by the customer; can be programmed to initiate a shutdown or warning.
1319	High alternator temp	High alternator temp	Warning
1321	Common warning driver	Common warning driver	Warning
1322	Load gov kW setpoint oor hi	Load gov kW setpoint oor hi	Shutdown
1323	Load gov kW setpoint oor lo	Load gov kW setpoint oor lo	Shutdown
1324	Load gov kVAR oor hi	Load gov kVAR oor hi	Warning
1325	Load gov kVAR oor lo	Load gov kVAR oor lo	Warning
1326	Backup starter disconnect	Category B	Warning
1327	Load gov kW analog oor	Load gov kW analog oor	Shutdown
1328	Genset CB tripped	Genset CB tripped	Warning
1329	AVR DC power failure	Category B	Warning
1331	AVR driver shorted	Category A	Shutdown
1332	Manual switch oor lo	Manual switch oor lo	Shutdown
1333	Manual switch oor hi	Manual switch oor hi	Shutdown
1334	Critical scaler oor	Critical scaler oor	Shutdown	Correct the feature/calibration entered into the control
1335	Noncrit Scaler Out Of Range	Non critical scaler oor	Warning	Correct the feature/calibration entered into the control
1336	Cooldown complete	Cooldown complete	Shutdown
1337	No Message	Network wink	Info
1341	Load demand stop	Load demand stop	Shutdown
1342	Slot 0 card	Slot 0 card	Shutdown
1343	Slot 1 card	Slot 1 card	Shutdown
1344	Slot 2 card	Category A	Shutdown
1345	Slot 3 card	Slot 3 card	Shutdown
1346	Slot 4 incorrect	Slot 4 incorrect	Shutdown
1347	Slot 5 card	Category A	Shutdown
1348	Slot 6 card	Category A	Shutdown
1349	Slot 7 card	Category A	Shutdown
135	Oil pressure sensor	Oil pressure sensor	Warning	Verify fault simulation not enabled (InPower); inspect sensor and engine harness connector pins; use oil pressure sensor simulator to check control response, replace sensor if it responds; check P7-13, 17, 21 for short (>200k ohms OK) and open (10 ohms or less OK)
1351	Slot 4 / network enabled	Slot 4 / network enabled	Warning
141	Oil pressure sensor	Oil pressure sensor	Warning	Verify fault simulation not enabled; inspect sensor/harness connector pins; use simulator to check control response; check P7-13, 17, 21 short/open
1414	Run relay contact	Run relay contact	Warning
1415	Run relay driver	Run relay driver	Warning
1416	Fail to shutdown	Fail to shutdown	Warning	Status - indicates the Fault Bypass mode is enabled (used primarily by service personnel for troubleshooting). The genset ignores the majority of system shutdown faults.
1417	Powr Down Error	The control has failed to go to sleep	Warning	Possible base board fault
1419	Fuel rail driver	Fuel rail driver	Warning
1421	Timing rail driver #1	Timing rail driver #1	Warning
1422	Timing rail driver #2	Timing rail driver #2	Warning
1424	High side driver	High side driver	Warning
1427	Overspeed relay driver	Overspeed relay driver	Warning
1428	LOP shutdown relay driver	LOP shutdown relay driver	Warning
143	Pre-Low Oil Pressure	Low oil pressure	Warning	Verify fault simulation not enabled; check oil level, lines and filters; use oil pressure sensor simulator; check +5 VDC at sensor (E1-A) and at P7-21; use simulator to P7-13 (OP OUT) and P7-17 (OP COMM); isolate to harness or base board
1433	Emergency stop - local	Local Emergency Stop	Shutdown	Pull the Emergency stop button out; move the O/Manual/Auto switch to O; press the front panel Fault Acknowledge/Reset button; select Manual or Auto as required

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Procedures

Aligning Generator with Engine (Angular Alignment) adjustment

⚠ Accidental starting of the generator set during this procedure presents the hazard of severe personal injury or death.

Tools: Dial indicator, Shims

Disconnect the negative (-) battery cable(s) before beginning.
Fasten a dial indicator to the generator shaft or cooling fan with the sensing point on the capscrew head or flat surface of the drive disc at the bolt circle diameter.
Bar the engine over in a clockwise rotation as viewed from engine flywheel; do not allow it to roll back on compression.
Determine the total indicator reading (T.I.R.) as the sum of the maximum positive and negative dial indicator readings over one revolution.
Measure the distance from the center of the generator shaft to the indicator measuring point.
Measure the distance from the generator side of the flex discs to the center of the generator mounting bolt.
Compare the distances; multiply this ratio times one half the T.I.R. to approximate the amount of shims to remove or add.

Alternator Belt - Adjust adjustment

⚠ The lower jam nut has left-hand threads.

Loosen alternator and adjusting link mounting capscrews.
Loosen jam nuts on adjusting screw.
Turn adjusting screw clockwise to tighten belt tension.
Tighten jam nuts to 55 Nm [40 ft-lb].
Tighten adjusting link and alternator mounting capscrews to 55 Nm [40 ft-lb].
Check belt tension again.

Angular Alignment Procedure adjustment

⚠ Accidental starting of the generator set during this procedure presents the hazard of severe personal injury or death. Make sure to disconnect the negative (-) battery cable(s) before beginning.

Tools: Dial indicator, Wooden shims

Disconnect the negative (-) battery cable(s) before beginning.
Fasten a dial indicator to the generator shaft or cooling fan with sensing point on capscrew head or flat surface of drive disc at bolt circle diameter.
Bar the engine over in a clockwise rotation as viewed from engine flywheel; do not allow it to roll back on compression.
Record maximum positive and negative dial indicator readings as the engine completes one revolution.
T.I.R. equals the sum of the maximum positive and negative readings.
Maximum T.I.R. should not be more than .001 inch for each inch of radius.
Remove equal shims from under both generator mounting feet to lower the generator.

Angular Alignment Procedure (Generator to Engine) adjustment

⚠ Accidental starting during this procedure presents the hazard of severe personal injury or death.

⚠ Do not bar engine over by prying on fan blade.

Tools: dial indicator

Disconnect the negative (-) battery cable(s) before beginning.
Fasten a dial indicator to the generator shaft or cooling fan with sensing point resting on the drive disc capscrew head/flat surface at the bolt circle diameter.
Bar the engine over in a clockwise rotation as viewed from the engine flywheel; do not allow it to roll back on compression at the end of travel of each reading.
Record the total indicator reading (T.I.R.) as the sum of the maximum positive and negative dial indicator readings over one engine revolution.
Compare the measured T.I.R. to the maximum allowed (.001 in. per inch of radius from center of shaft to indicator axis); add or remove shims under the generator mounting feet to correct.

Axial Alignment Procedure adjustment

Tools: Dial indicator with holding device (magnetic base or clamp)

Fasten dial indicator holding device to skid base, engine block, or generator shell with magnetic base or clamp.
Position so the sensor point rests on the generator shaft hub.
Bar the engine over clockwise (viewed from engine flywheel) through a couple of rotations.
Record indicator readings in eight equally spaced points around the shaft diameter to provide a T.I.R.
To correct an out-of-tolerance T.I.R., remove capscrews connecting drive discs and flywheel.
Mark the drive discs and flywheel with respect to each other.
Rotate engine or generator so drive disc holes are repositioned 180 degrees from original location.
Reinstall drive disc capscrews and retorque; re-check shaft alignment.
If T.I.R. unchanged, rotate discs to 30, 60, or 90 degrees from original location.
If T.I.R. does not improve, inspect flywheel pilot and drive disc runouts.

Axial Alignment Procedure (Generator to Engine) adjustment

Tools: dial indicator

Fasten a dial indicator holding device to the skid base, engine block, or generator shell with the sensor point resting on the generator shaft hub.
Bar the engine over in a clockwise rotation through a couple of rotations, recording indicator readings at eight equally spaced points around the shaft diameter to obtain axial T.I.R.
Reduce the measured T.I.R. runout by one half if excessive vibration remains after angular alignment.

Bus Voltage Calibration (C) adjustment

⚠ Contacting hazardous voltage components can cause electrocution, resulting in severe personal injury or death.

⚠ Improper calibration or adjustment of the PowerCommand control can cause equipment malfunction or damage.

Tools: Calibrated RMS multimeter (Fluke models 87 or 8060A)

Display the Bus Voltage Calibration submenu.
With all gensets OFF, attach a calibrated voltmeter to TB1-A (L1) and TB1-B (L2) of the bus PT module.
Start another genset and allow it to reach normal operating speed and voltage; connect to the bus.
Calibrate the voltage reading for Bus Volts L1 so display matches the calibrated meter.
Shut the generator set OFF.
Repeat steps 2 through 5 for Bus Volts L2 and L3.
Exit menu to Save changes.

Dipstick - Calibrate adjustment

⚠ Dipstick will break if scribe mark is too deep.

Tools: Scribe

Drain oil from oil pan.
Install dipstick in dipstick tube housing.
Fill oil pan to specified low level with clean 15W-40 oil.
Remove dipstick and scribe mark at oil level; mark low with L.
Install dipstick tube.
Add oil to specified full level.
Remove dipstick and scribe mark at oil level; mark high with H.

Generator Mount Pre-load Adjustment adjustment

⚠ Accidental starting of the generator set during this procedure presents the hazard of severe personal injury or death. Disconnect the negative (-) battery cable(s) before beginning.

Tools: Two 1 3/4" T x 2" W x 6" L steel spacers, Adequate lifting device

Turn off and disconnect battery charger (if equipped).
Disconnect the negative (-) battery cable(s) to prevent accidental starting.
Unscrew bolt (Item 2) from skid but do not remove from either rear engine vibration isolator.
Loosen the three screws that secure the engine mount brackets to the engine.
Loosen but do not remove the hex nut (Item 1) from the M20 screw of the generator vibration isolators.
Lift the generator until mounting feet brackets are high enough to insert a 1 3/4 inch steel spacer under both stator foot brackets.
Insert spacers and lower the generator so full weight rests on the mounting foot brackets.
Make sure no gap is present between skid and lower mount of rear engine vibration isolators.
Tighten the three screws to secure the bracket to the engine to 190-200 ft-lbs (260-270 N-m).
Lift the generator to remove the two 1 3/4 inch steel spacers.
Start the threads of the rear engine vibration isolator bolts (Item 2) before lowering.
Lower the generator and tighten the two rear engine vibration isolator bolts to 270-330 ft-lbs (365-447 N-m).
Secure the generator foot brackets to the vibration isolators and tighten to 270-330 ft-lbs (365-447 N-m).

Genset Ammeter Display Calibration (B) adjustment

⚠ Contacting hazardous voltage components can cause electrocution, resulting in severe personal injury or death.

⚠ Improper calibration or adjustment of the PowerCommand control can cause equipment malfunction or damage.

Tools: Calibrated RMS multimeter (Fluke models 87 or 8060A)

Display the Current Calibration submenu.
With the genset OFF, attach a calibrated ammeter to L1.
Start the genset and allow it to reach normal operating speed.
Load the genset to maximum rated kVA at rated voltage.
Calibrate the reading for L1 current so display agrees with calibrated ammeter.
Repeat steps 2 through 5 for L2 and L3.
Exit menu to Save changes.

Genset Voltage Display Calibration (A) adjustment

⚠ Contacting hazardous voltage components can cause electrocution, resulting in severe personal injury or death.

⚠ Improper calibration or adjustment of the PowerCommand control can cause equipment malfunction or damage.

Tools: Calibrated RMS multimeter (Fluke models 87 or 8060A)

Display the Voltage Calibration submenu.
With the genset OFF, attach a calibrated voltmeter to the AC output from L1 to L2 (L1 to Neutral for single phase).
Start the genset and allow it to reach normal operating speed.
Calibrate voltage reading for L1 so display agrees with the calibrated voltmeter.
Shut the generator set OFF.
Repeat steps 2 through 5 for L2 and L3.
Exit menu to Save changes.

Governor Calibration Checks adjustment

Tools: Frequency meter or tachometer, Jumper wire

Start the generator set.
Adjust engine no-load speed to the desired allowable speed droop using the Run Speed potentiometer.
With no load, turn GAIN clockwise slowly until engine speed oscillates.
Reduce GAIN slowly counterclockwise until engine speed is stable.
Upset the governor by momentarily shorting terminals 7 and 10 on the governor control.
Apply and remove loads to check generator set response.

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Voltage reconnection

Voltage	Phase	Connection	Leads	Notes
		12 lead generator sets	Load wires are routed through the CTs	Reconnectable gensets (12 leads) have dual secondary CTs (3 pins); CT wire 2/3 to pin 2 (high voltage) or pin 3 (low voltage).
		6 lead generator sets	Generator output leads are routed through the CTs	Non-reconnectable gensets (6 leads) have single secondary CTs (2 pins).
		Cummins PowerCommand generic AC Reconnect Wiring Diagram 625-2755 (Rev. D) and 625-3100 (Rev. F)		Applies to models DFAA, DFAB, DFAC, DFBF, DFCB, DFCC, DFEB, DFEC, DFFB, DFGA, DFGB, DFJA, DFJB, DFJC, DFJD, DFLB, DFLC, DFLD, DFMB (625-2755) and models DFAA-DFMB plus DFCE, DFED, DQAA, DQAB, DQBA, DQBB (625-3100).
	A (U)	CT21	U load leads (A phase)	CT dot must face the generator; CT terminal 1 connects to metering circuit, terminal 2/3 to ground.
	B (V)	CT22	V load leads (B phase)	CT dot must face the generator; terminal 1 to metering circuit, terminal 2/3 to ground.
	C (W)	CT23	W load leads (C phase)	CT dot must face the generator; terminal 1 to metering circuit, terminal 2/3 to ground.
110/190	3		12	Full load current at Standby rating: 1901 A
110/220	3		12	Full load current at Standby rating: 1642 A
115/230	3		12	Full load current at Standby rating: 1571 A
120/208	3		12	Full load current at Standby rating: 1737 A
139/240	3		12	Full load current at Standby rating: 1505 A
220/380	3		12	Full load current at Standby rating: 951 A
230/400	3		12	Full load current at Standby rating: 903 A
240/416	3		12	Full load current at Standby rating: 868 A
255/440	3		12	Full load current at Standby rating: 821 A
277/480	3	Wye, 4 Wire	12	Full load current at Standby rating: 753 A
277/480	3	Wye, 4 wire	12	Alternator 60 Hz, 12 lead, limited range, 125 °C; single phase power may be taken at up to 40% of nameplate kW at unity power factor
347/600	3		12	Full load current at Standby rating: 602 A

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Parts cataloged across the Cummins/Onan KTA19 family

Part #	Description	Category
CS-1367-1	COOLANT FILTER	Coolant filter
25-1386	FUEL FILTERS	Fuel filter
FS-1386-1	fuel filters	Fuel filter
903-0125	NA	Service part / kit
903-0205	NA	Service part / kit
903-0605	NA	Service part / kit
A134	engine control monitor board	Service part / kit
D1400	DONALDSONS D1400 SOLVENT	Service part / kit
ES-1778-1	current transformer connections	Service part / kit
ES-1866-1	reconnection diagram	Service part / kit
LS-1063-1	oil dipstick location	Service part / kit
M-1808-2	typical installation diagram	Service part / kit
SC-1101-1	load transfer switch	Service part / kit

Parts cataloged across all variants of this engine family — verify the exact part fits your specific variant and serial number before ordering.

Common questions

What is the oil capacity of the Cummins/Onan KTA19?

The Cummins/Onan KTA19 engine has an oil capacity of 45.0 liters.

What is the displacement of the Cummins/Onan KTA19?

The Cummins/Onan KTA19 has a displacement of 18.7 liters.

Which generators use the Cummins/Onan KTA19 engine?

The Cummins/Onan KTA19 powers 1 generator set(s), including Cummins/Onan DFE.

How often should you change the oil in the Cummins/Onan KTA19?

The Cummins/Onan KTA19 oil change interval is every 250 hours.

What is a common problem with the Cummins/Onan KTA19 engine?

A commonly reported issue on generators using the Cummins/Onan KTA19 is: Over Current.

Cummins/Onan KTA19 Engine

Engine specifications

Generator sets powered by this engine

Troubleshooting

Fault codes

Common problems

Maintenance schedule

Repair guides

Service intervals

Service specifications

Recommended fluids

Fault codes

Procedures

Voltage reconnection

Parts cataloged across the Cummins/Onan KTA19 family

Common questions