Service parts for the XP13000HX
Grouped by system, with how many of each the parts manual calls for.
Ignition
1 required30010-Z010210-00A0Spark plugfind
Prices captured from merchant listings; some links are affiliate links. Confirm against your serial number before ordering.
Specifications
| Fuel | Gasoline/Propane (Dual Fuel) |
|---|---|
| Frequency | 60.0 Hz |
| Oil capacity | 40.5 L |
| Voltage options | 120 V, 240 V |
| Phase | Single |
| Rated current | 87.50 (120V) / 43.75 (240V) A |
| Battery voltage | 12V V |
| Battery quantity | 1 |
| Dimensions (L×W×H) | 30×29×26 mm |
| Dry weight | 246 kg |
| Sound level | 74.0 dBA |
| Fuel tank | 8.3 L |
| Tank runtime | 8.5 hr (gasoline) / 6.5 hr (propane, 40 lb.) hr |
Maintenance & consumables
| Item | Spec | Capacity | Part # | Interval | |
|---|---|---|---|---|---|
| Air filter | check | — | 300 hr | ||
| Fuel filter | — | 50 hr | |||
| Oil | — | 50 hr | |||
| Spark plug | 16 ± 1.5 ft. lbs. (22 ± 2 N·m) | 30010-Z010210-00A0 | 300 hr | buy |
Service intervals
18| Item | Action | Hours | Months | Notes |
|---|---|---|---|---|
| Engine Oil | Change | 20 hr | 1 mo | First service — 1st month or 8 hrs (break-in) |
| Air Cleaner | Check | 20 hr | 1 mo | |
| Air Cleaner | Change | 100 hr | 6 mo | |
| Sediment Cup | Clean | 50 hr | 3 mo | Every 3 mo or 50 hrs of heavy use |
| Spark Arrestor | Check | 50 hr | 3 mo | Every 3 mo or 50 hrs of heavy use |
| Spark Plug | Clean | 50 hr | 3 mo | Clean-adjust |
| Idle Speed | Check | 100 hr | 6 mo | Check/adjust |
| Spark Arrestor | Clean | 100 hr | 6 mo | |
| Spark Plug | Adjust | 100 hr | 6 mo | Clean/Adjust; every 6 mo or 100 hrs of normal use |
| Spark Plug | Replace | 100 hr | 6 mo | |
| Carbon Brushes | Inspect | 250 hr | Inspected in conjunction with AVR | |
| Fuel Tank/Filter | Clean | 300 hr | 12 mo | |
| Idle Speed | Adjust | 300 hr | 12 mo | Check/Adjust; every 12 mo or 300 hrs |
| Valve Clearance | Check | 300 hr | 12 mo | Check-adjust |
| Combustion Chamber | Clean | 500 hr | 36 mo | Every 3 yrs or 500 hrs |
| Fuel Tank / Filter | Clean | 500 hr | 36 mo | Every 3 yrs or 500 hrs |
| Valve Clearance | Adjust | 500 hr | 36 mo | Check/Adjust; every 3 yrs or 500 hrs |
| Fuel Tube | Check | 300 hr | 24 mo | Replace if necessary |
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Service specifications
1| Type | Item | Value | Unit | Condition |
|---|---|---|---|---|
| Gap | Spark plug gap | 0.7-0.8 | mm (0.028-0.031 in) |
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Recommended fluids
| Fluid | Grade | Standard | Ambient | Capacity | Notes |
|---|---|---|---|---|---|
| Engine oil | SAE 10W-30 | 40.5 fl. oz (1.2L) | 5W-30 for colder temps per chart; do not use oils with additives or 2-stroke oil | ||
| Engine oil | SAE 10W-30 (5W-30 synthetic for cold) | 40.5 fl oz (1.2L) | Do not use oils with additives or 2-stroke oil | ||
| Engine oil | SAE 10W-30 (Full synthetic 5W-30 after break-in) | 40.5 fl. oz (1.2L) | Do not use additive oils or 2-stroke oils | ||
| Fuel | Fresh unleaded gasoline, octane 87 or higher | 8.3 US Gal. (31L) |
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Procedures
10Adding Oil maintenance
⚠ Do not overfill the crankcase
Tools: Funnel
- Make sure generator is on a level surface
- Unscrew the oil filler/dipstick cap
- Using a funnel, add oil until level reaches lower lip of the fill opening
- Replace the oil filler cap
Changing the Oil maintenance
⚠ Worn out or dirty oil does not cool the generator properly
Tools: 12mm hex wrench
- Unscrew the oil drain plug with a 12mm hex wrench and drain oil into approved container
- Replace drain plug and tighten with 12mm hex wrench
Cleaning the Air Filter maintenance
- Remove filter cover screw
- Remove filter cover and sponge-like element
- Wipe dirt from casing
- Wash element in dish detergent and warm water
- Pat dry with cloth
- Soak dry element in engine oil, ring out excess
- Replace elements in casing
Emptying the Gas Tank maintenance
⚠ Do not store fuel from one season to another
Tools: wrench
- Turn fuel valve to OFF
- Unscrew fuel filter cup from fuel valve using wrench
- Empty fuel filter cup of any fuel
- Turn fuel valve to ON, drain all gas into funnel/container
- Turn fuel valve to OFF
- Reinstall fuel filter cup
- Store emptied gasoline with fuel stabilizer
Spark Plug Maintenance maintenance
Tools: spark plug wrench, wire brush
- Pull spark plug cap off
- Unscrew spark plug with spark plug wrench
- Inspect for cracks/chips, discard if damaged
- Measure plug gap, should be 0.7-0.8 mm (0.028-0.031 in)
- Clean and re-gap if reusing
- Install spark plug
- Replace spark plug cap
Storing the Generator for Longer Than 30 Days maintenance
- Turn breaker OFF and run generator 3-5 minutes
- Shut fuel valve OFF and run until engine stalls
- Turn battery switch OFF
- Empty the gas tank
- Drain the carburetor via the drain bolt
- Remove spark plug, add 2 tbsp of 10W-30 oil into the spark plug hole, pull recoil to lubricate cylinder, reinstall spark plug
- Remove the battery and place on a 12V battery tender indoors
Changing / Inspecting the AVR repair
⚠ If generator is overheated or overloaded, AVR may be damaged and require replacement
- Remove 2 bolts of generator cover, pull cover off
- Remove 2 bolts holding AVR
- Disconnect wire clip
- Remove 2 wires from AVR on carbon brush
- Install new AVR with 2 bolts
- Insert and connect 2 wires from AVR to brush
- Reconnect wire clip
- Replace back cover with 2 bolts
Changing / Inspecting the Carbon Brushes repair
⚠ Inspect every 250 running hours
- Remove 2 bolts of generator cover, pull cover off
- Remove bolt holding carbon brush
- Remove 2 wires from AVR on carbon brush
- Install new carbon brush with bolt
- Insert and connect 2 wires from AVR, connect + and - correctly
- Replace back cover with 2 bolts
Changing/Inspecting the AVR repair
- Remove 2 bolts of generator cover and pull cover off
- Remove 2 bolts holding the AVR
- Disconnect wire clip
- Remove 2 wires from AVR on carbon brush
- Install new AVR with 2 bolts
- Reconnect wires to brush, observe polarity
- Reconnect wire clip
- Replace generator cover
Changing/Inspecting the Carbon Brushes repair
- Remove 2 bolts of generator cover and pull cover off
- Remove bolt holding carbon brush
- Remove 2 wires from AVR on carbon brush
- Install new carbon brush with bolt
- Connect AVR wires, observe polarity
- Replace generator cover with 2 bolts
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Common questions
What fuel type does the DuroMax XP13000HX take?
The DuroMax XP13000HX runs on Gasoline/Propane (Dual Fuel).
Troubleshooting
6Symptoms & remedies
| Symptom | Cause | Remedy |
|---|---|---|
| Engine will not start | Engine switch is “OFF” Fuel valve is “CLOSED” Choke is open The engine is out of fuel is old or contaminated Spark plug is dirty Spark plug is broken | Set engine switch to “RUN” Turn the fuel valve to “OPEN” Close the choke Add fuel Change fuel Clean spark plug Replace spark plug |
| Engine runs, but there is no electrical output | The circuit breaker is “OFF” Turn “ON” circuit breaker | |
| Generator runs but does not support all electrical devices connected | Generator is overloaded Disconnect 1 or more items to reduce the load | |
| Device connected to generator is bad | Disconnect malfunctioning device | |
| The air filter is dirty | Clean/replace the air filter | |
| The engine will not start | Engine switch is “Off” | Set engine switch to “On” |
Fault codes and symptom→remedy steps extracted from this model’s service/owner documentation; verify against the official manual before servicing. Full DuroMax XP13000HX troubleshooting guide (11 entries) →
Parts
23| Part # | Description | Qty | System | |
|---|---|---|---|---|
| 09100-Z170410-0000 | Starting Motor Assembly | Assembly | buy | |
| 11001-Z0D0110-0000 | Crankcase Cover Gasket | Gasket | buy | |
| 11007-Z080110-00A0 | Oil Drain Bolt | Bolt | buy | |
| 11310-Z0D0110-0BA0 | Crankcase | Housing | buy | |
| 11411-Z0D0110-0BA0 | Crankcase Cover | Housing | buy | |
| 12004-Z0J0510-0000 | Valve Cover Gasket | Gasket | buy | |
| 12131-Z0D0210-0000 | Cylinder Head Gasket | Gasket | buy | |
| 12140-Z0D0210-0BA9 | Cylinder Head Assembly | Assembly | buy | |
| 12410-Z0J0211-00A0 | Valve Cover | Housing | buy | |
| 13010-Z0D0311-00A0 | Connecting Rod | Rod | buy | |
| 13111-Z0D0210-00A0 | Piston | Piston | buy | |
| 13121-Z1X0110-0000 | Pin | Pin | buy | |
| 13122-Z100110-00A0 | Pin Clip | Clip | buy | |
| 13200-Z0D0110-00A9 | Piston Rings | Ring | buy | |
| 13300-Z0D0110-CLAT | Crankshaft Assembly | Assembly | buy | |
| 15010-Z080330-Q500 | Oil Fill Cap/Dipstick | Cap/dipstick | buy | |
| 17004-Z0D0110-00A0 | Breather Tube | Tube | buy | |
| 30010-Z010210-00A0 | Spark Plug | Spark plug | buy | |
| 37060-Z080120-0000 | Oil Sensor | Sensor | buy | |
| 90547-0208-CLAE | Crankshaft Bearing | Bearing | Amazon eBay | |
| 90548-0202-CLA0 | Bearing | Bearing | Amazon eBay | |
| 93140-Z2F0110 | Jet Kit for 3,000 ft. - 6,000 ft. | Service part / kit | Amazon eBay | |
| 93141-Z2F0110 | Jet Kit for 6,000 ft. - 8,000 ft. | Service part / kit | Amazon eBay |
Service, wear & replacement parts referenced for this model and its engine — confirm the exact part for your serial number. See the full parts catalog to search and cross-reference.
Available documents
Spec sheet (DuroMax)Reference (DuroMax)Owner's manual (DuroMax)Owner's manual — c85f788c-34c1-40c8-9ae5-ff2aaf5e17ce (DuroMax)Service manual — xp13000hx servicemanual revised 03062023 web 2f7e871e-e7ad-4cf8-9389-3b76a05d9cea (DuroMax)