Home›Engines›Cummins/Onan QSX15-G9

Cummins/Onan QSX15-G9 Engine

The Cummins/Onan QSX15-G9 is a 14.9 L 6-cylinder turbocharged with air-to-air charge air-cooling engine rated at 1800 rpm. It powers generator sets from Cummins/Onan, Katolight and MQ Power, including the 350DFEG, 450 DFEJ, 500 DFEK and C450D6. It holds 83.3 L (22.0 gal) of oil and 57.9 L (15.3 gal) of coolant.

Also known as: Cummins QSX15-G9, QSX15 G-9

Part of the Cummins/Onan QSX15 engine family — 8 variants share parts & fitment.

14.9 L

Displacement

Cylinders

1800 rpm

Rated speed

83.3 L

Oil capacity

On this pageSpecs Generator sets Maintenance FAQ Service intervals Torque & specs Fluids Fault codes Procedures Wiring

Engine specifications

Oil capacity	83.3 L
Coolant capacity	57.9 L
Displacement	14.9 L
Cylinders	6
Aspiration	Turbocharged with air-to-air charge air-cooling
Rated speed	1800 rpm

Generator sets powered by this engine

Shared across brands: Cummins/Onan, Katolight, MQ Power

Cummins/Onan 350DFEG Cummins/Onan 450 DFEJ Cummins/Onan 500 DFEK Cummins/Onan C450D6 Cummins/Onan DFE Cummins/Onan DFEJ Cummins/Onan DFEKCummins/Onan DFEK-5737120Katolight D500FJZ4 Katolight D500FNZ4 Katolight D500FPZ4 Katolight D500FRZ4 MQ Power CG500C2

How to read your Cummins/Onan engine serial & model number →

Common problems

Over Current 1471
Low AC Voltage 2331
High AC Voltage 2358
Voltage on any phase has dropped below a preset value. 27
Output voltage on any phase exceeds preset values. 59
Generator set output frequency cannot be maintained. 81 u
Generator set is operating at a potentially damaging frequency level. 81 o
Speed Signal Lost 121
Weak Battery 1442
Warning, Shutdown, and Non-Automatic lamps are not lit. Digital display shows main menu or selected menu.
Cause: Indicates all engine systems are normal. No corrective action required
Warning Status Indicator: This yellow lamp is lit whenever the control detects a warning condition.
Fix: After the condition is corrected, warning indicators can be reset by pressing the Fault Acknowledge button. (It is not necessary to stop the generator set if the fault becomes inactive during genset operation.)
Warning lamp lights.
Cause: LOW COOLANT TEMP 210 – WARNING
Fix: Set is in standby mode but is not operating. Warning occurs when engine coolant temperature is 70° F (21° C) or lower. NOTE: In applications where the ambient temperature falls below 40°F (4°C), Low Engine Temp may be indicated even though the coolant heaters are operating.
Under frequency shutdown (81 u) - Generator set output frequency cannot be maintained. 81 u
Under Frequency 1448
Too Long in Idle 2342

Compiled from service & troubleshooting documentation across every generator set that uses the Cummins/Onan QSX15-G9.

Maintenance schedule

Item	Spec	Capacity	Part #	Interval
Air filter			L028-2	50 hr	eBay
Fuel filter	New o-ring seal supplied with the new filter. For Biodiesel applications use gasket pack 3950445 S (green) and change with every filter change.		—
Oil filter	Single spin-on combination full flow and bypass filters		—	500 hr
Battery	1400 Amps minimum at ambient temperature 0 °C (32 °F)		—	100 hr
Coolant	57.9 L (15.3 US gal)	57.9 L	—	8 hr
Oil	83.3 L (88.0 qt)	88.0 L	—	8 hr

Pooled from every document that names this exact engine — confirm the interval and part number against your unit's serial number.

Repair guides

Step-by-step procedures compiled from the Cummins/Onan service manual for this engine.

Service intervals

Item	Action	Hours	Months	Notes
Air cleaner	Check	250 hr	6 mo	X1; replace as necessary; refer to QSX15 engine manual
All hardware (fittings, clamps, fasteners)	Check	8 hr		Daily or after 8 hrs.
All hardware (fittings, clamps, fasteners, etc.)	Check	100 hr		Daily or after 8 hours
Anti-freeze and DCA concentration	Check	250 hr	6 mo	X1; refer to QSX15 engine manual
Coolant heater(s)	Check	100 hr		Daily or after 8 hrs.
Drive belt	Check	250 hr	6 mo	X1; refer to Cummins QSX15 Series Engine Operation and Maintenance Manual for interval/procedure
Engine oil level	Check	8 hr		Daily or after 8 hrs.
Fuel filter(s)	Drain	250 hr	6 mo	X1; refer to QSX15 engine manual
Genset	Inspect	8 hr		Daily; check for oil, fuel, cooling and exhaust system leaks
Radiator hoses for wear and cracks	Check	250 hr		Daily or after 8 hours
Charge Air Piping	Check	50 hr		Weekly
Coolant heater	Check	50 hr		Weekly or after 50 hours
Coolant level	Check	50 hr		Weekly or after 50 hours
Exhaust condensate trap	Drain	100 hr		Drain water to prevent it flowing back into the engine
Fuel level	Check	50 hr		Weekly or after 50 hours
Oil level	Check	50 hr		Weekly or after 50 hours
Air cleaner	Clean	100 hr		Monthly or after 100 hours; clean if required, perform more often in dusty conditions
Battery charging system	Check	100 hr		Monthly or after 100 hours
Battery electrolyte level	Check	200 hr	1 mo	Monthly or after 100 hrs. Also check at least every month or 100 hours of operation, whichever occurs first.
Fuel tank water and sediment	Drain	100 hr		Monthly or after 100 hours
General set inspection	Inspect	100 hr		Monthly or after 100 hours (Table 5-1, footnote X2): check for oil, fuel, cooling and exhaust system leaks; check exhaust system audibly and visually with set running
General set inspection (oil, fuel, coolant, exhaust leaks; exhaust audibly and visually with set running)	Inspect	100 hr		Monthly or after 100 hrs, whichever is sooner.
Generator air outlet	Check	100 hr		Monthly or after 100 hrs.
Radiator hoses	Check	500 hr	12 mo	Monthly or after 100 hrs; check for wear and cracks.
Starting batteries	Check	100 hr		Check condition and terminals
Air cleaner	Replace	250 hr		Check air cleaner; replace as necessary. Refer to QSX15 manual.
Crankcase oil and filter	Change	250 hr	12 mo	Prime power: every 6 months or 250 hours; standby: every 12 months or 250 hours, whichever comes first
Drive belt tension	Check	250 hr	6 mo	Visually check belt for wear or slippage; replace if hard or brittle
Engine oil and filter	Replace	250 hr	6 mo	X1; 6 Months or After 250 Hrs; refer to QSX15 engine manual
Radiator Hoses	Inspect	250 hr	6 mo	Check for wear & cracks
Water coolant filter	Replace	250 hr	6 mo	X1; 6 Months or After 250 Hrs
Air cleaner element	Change	500 hr	12 mo	Yearly or after 500 hours; clean if required more often
Coolant filter	Change	500 hr	12 mo	Yearly or after 500 hours; refer to engine operation and maintenance manual
Cooling system	Clean	500 hr	12 mo	Yearly or after 500 hours; drain and replace coolant mixture
Crankcase breather	Clean	500 hr	12 mo	Yearly or after 500 hours
Engine oil and filter	Change	500 hr	12 mo	Table 5-1, footnote X1
Fuel filter	Change	500 hr	12 mo	Table 5-1, footnote X1
Fuel filters	Change	500 hr	12 mo	Yearly or after 500 hours
Generator insulation resistance	Test	500 hr	12 mo	Follow periodically throughout life of set or if generator has set idle with no heaters; contact authorized service center
Water coolant filter	Change	500 hr	12 mo	Table 5-1, footnote X1

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Service specifications

Type	Item	Value	Unit	Condition
Clearance	Angular alignment maximum T.I.R.	0.001	inch per inch of radius (center of shaft to indicator axis)	measuring deflection to bolt heads
Clearance	Exhaust pipe clearance from combustible wall or partition	12	inches (305 mm)	minimum
Clearance	Exhaust pipe clearance to combustible wall or partition	305	mm
Clearance	Exhaust pipe clearance to combustible wall/partition	12	inches (305 mm)
Clearance	Exhaust pipes to combustible wall or partition	305 mm (12 inches)	mm
Clearance	Float switch assembly float lift clearance below C-clip stop	1/8	inch (3 mm)	use a feeler gauge
Clearance	Fuel line clearance from electrical wiring	1/2	inch (12.7 mm)
Clearance	Fuel line clearance from hot exhaust parts	2	inch (51 mm)
Clearance	Fuel lines - minimum clearance from electrical wiring	12.7	mm
Clearance	Fuel lines - minimum clearance from hot exhaust parts	51	mm
Clearance	Fuel lines to electrical wiring	12.7 mm (1/2 inch) minimum	mm
Clearance	Fuel lines to hot exhaust parts	51 mm (2 inches) minimum	mm
Clearance	Generator mount pre-load steel spacer thickness	1 3/4	inch	two spacers under both stator foot brackets
Clearance	Generator-to-engine angular alignment (T.I.R.)	.001 in. per inch of radius (center of shaft to indicator axis), maximum	in	750 kW gensets and larger
Clearance	MPU installation gap adjustment	back out 1/4 turn after touching gear tooth	turn
Clearance	Minimum clearance of fuel lines from electrical wiring	12.7	mm (1/2 inch)
Clearance	Minimum clearance of fuel lines from hot exhaust parts	51	mm (2 inch)
Clearance	Service/maintenance access clearance around generator set	1	meter
Clearance	Vibration isolator base elevation difference	0.25	inch (6 mm)	shimmed or grouted within this of each other
Clearance	Vibration isolator clearance	0.25	inch (6 mm)
Clearance	Vibration isolator clearance between top plate and base	6 mm (0.25 inches) or greater	mm	nominal
Clearance	Vibration isolator nominal clearance (leveling bolt)	0.25	inch (6 mm)	minimum, or greater
Gap	Coolant level below radiator cap lower sealing surface	3/4 inch (18 mm)	inch (mm)
Gap	MPU sensor to flywheel ring gear tooth	back it out one quarter turn	turn	sensor threaded in until it just touches gear tooth
Other	AC control wire strip length	6.0 mm (0.236 in) screw type; 10 mm (0.75 in) push type	mm
Other	AVR Droop setting	5	% at full load, 0 PF
Other	AVR voltage regulation (load regulation)	approximately ±0.5	% RMS
Other	Ambient temperature below which coolant heaters recommended (NFPA 110)	40	°F
Other	Amperage PH1	0, 615, 615, 614, 613, 613, 0	A	warm up / start / 15 min / 30 min / 45 min / 1 hour / cool down
Other	Amperage PH2	0, 618, 618, 617, 618, 617, 0	A	warm up / start / 15 min / 30 min / 45 min / 1 hour / cool down
Other	Amperage PH3	0, 612, 612, 611, 611, 611, 0	A	warm up / start / 15 min / 30 min / 45 min / 1 hour / cool down
Other	Angular alignment maximum T.I.R.	.001 inches per inch of radius	in/in	center of shaft to indicator axis
Other	Battery CCA (minimum)	1400	CCA	Cold Soak @ 0° F (-18° C)
Other	Battery charging alternator output	35	Amps
Other	Battery electrolyte maximum permissible temperature during charge	45 °C (113 °F)	°C	during charge
Other	Battery electrolyte specific gravity	1.260	SG	corrected at 25 °C (77 °F); charge if below 1.215
Other	Battery electrolyte specific gravity, for filling new cells, ambient normally below 32 °C (90 °F)	1.270	SG
Other	Battery specific gravity (fully charged)	1.26	specific gravity	at 80 F (27 C)
Other	Battery specific gravity (high ambient, above 95F/35C)	1.225		recommended to reduce electrolyte loss
Other	Battery specific gravity (recharge threshold)	below 1.260
Other	Battery specific gravity charge threshold	1.215	corrected	charge battery if reading below
Other	Battery specific gravity fully charged	1.260	corrected	add 0.004 per 10 F above 80 F (27 C)
Other	Battery specific gravity, fully charged	approximately 1.260	specific gravity	at 80 F (27 C)
Other	Battery specific gravity, fully charged, corrected	1.260	SG	at 25 °C (77 °F)
Other	Battery temperature sensor fault trip temperature (fault code 2263)	55	°C	131 °F
Other	Battery terminal cleaning solution	1/4 pound baking soda to 1 quart water
Other	CAN datalink main trunk maximum length	40	meters	no more than 30 devices
Other	CAN datalink stub maximum length	1	meter	stub from main trunk to each module
Other	CAN datalink transmission speed	250	KBaud
Other	Charge battery if specific gravity below	1.215	specific gravity
Other	Charge battery if specific gravity reading is below	1.215	SG
Other	Compression ratio	17.0:1
Other	Cooling system make-up water maximum calcium/magnesium (hardness)	170	ppm (as CaCO3)
Other	Cooling system make-up water maximum chloride	40	ppm (as Cl)
Other	Cooling system make-up water maximum sulfate	100	ppm (as SO4)
Other	Default starting cycles	3 (15 seconds cranking, 30 seconds rest)	cycles	configurable 1-7 cycles
Other	Engine Hours	371.2, 371.3, 371.5, 371.8, 372, 372.3, 372.4	h	warm up / start / 15 min / 30 min / 45 min / 1 hour / cool down
Other	Exhaust flow at rated load	2900	cfm (1370 L/s)	1500 RPM
Other	Exhaust flow at rated load	3200	cfm (1510 L/s)	1800 RPM
Other	Exhaust outlet size	4	in. NPD

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Recommended fluids

Fluid	Grade	Standard	Ambient	Capacity	Notes
Coolant		Refer to Cummins QSX15 Series Engines Operation and Maintenance Manual for coolant recommendations/specifications		58.0 L	Cooling System (Capacity Std. Radiator) printed as 15.3 Gal (58 L); check anti-freeze and DCA concentration
Coolant	50% ethylene glycol and water (also propylene glycol permitted)	Cummins Engineering Standard 14603; Fleetguard Compleat ES low-silicate antifreeze or equivalent; DCA4 required if not using Fleetguard Compleat		57.9 L	Coolant capacity with standard set-mounted radiator 15.3 Gal (57.9 L). Add coolant at 50 °C (122 °F) or lower. Fill to bottom of fill neck in radiator or expansion tank. Some radiators have two fill necks, both must be filled.
Coolant	Balanced coolant mixture of water and antifreeze	Refer to Cummins engine Operation and Maintenance Manual		90.0 L	Capacity with standard radiator 24 Gal (90 L); drain and replace mixture every year or after 500 hours; add until 3/4 inch (18 mm) below radiator cap lower sealing surface
Coolant	soft water / E.G. / DCA mixture				Cooling system to be filled with soft water/E.G./DCA mixture (on-site review checklist).
Engine oil		Refer to Cummins QSX15 Series Engines Operation and Maintenance Manual for lubricating oil classification/viscosity		58.0 L	Oil Cap. w/Filters printed as 26 Gallons (58 L); gense is shipped filled with correct type and quantity of oil
Engine oil	high-quality multi-viscosity lubricating oil	Cummins Premium Blue or equivalent		83.3 L	Oil capacity with filters 88 qt (83.3 L). Do not operate with oil below the L mark or above the H mark. Special running-in oils are not recommended.
Fuel	ASTM D975 Grade 2	BS EN 590:2000 (automotive diesel); BS 2869:2010+A1:2011 (fuel oils for agricultural, domestic and industrial engines and boilers)			Never use galvanized or copper fuel lines, fittings, or fuel tanks
Fuel	ASTM D975 No. 2-D	Cetane number 40-50, 300-500 ppm Sulfur			Diesel fuel specifications
Fuel	ASTM No. 2 diesel				Cummins engines normally use ASTM No. 2 diesel fuel.
Fuel	ASTM No. 2D diesel	BS 2869:2010+A1:2011 acceptable alternative			Minimum Cetane number 40. Cetane above 40 may be needed at high altitude or extremely low ambient temperatures. Do not mix gasoline or alcohol with diesel fuel. Keep tanks as full as possible to avoid condensation.
Fuel	Diesel				Day tank fuel transfer pump maintains reservoir of diesel fuel in the day tank.
Fuel	Diesel fuel specified to ASTM No. 2 or BS EN 590:2000, Automotive fuels	ASTM No. 2 / BS EN 590:2000			An electric solenoid valve in the supply line is recommended for all installations and required for indoor automatic or remote starting installations. Never use galvanized or copper fuel lines, fittings or fuel tanks.
Fuel	diesel	ASTM No. 2 or BS EN 590:2000			Cummins engines normally use a diesel fuel specified to ASTM No. 2 or BS EN 590:2000; alternate diesel fuels within the specifications shown in the Generator Set Operator Manual (0908-0219)
Grease	Lithium based grease	Mobilux No. 2 or Shell Alvania R3		2.74 oz (81 ml)	Generator end bearing. Temperature range -22F to +248F (-30C to +120C). Grease should be equally divided between the bearing, bearing cap cavity, and bearing cartridge cavity.
Grease	Lithium based grease, Mobilux No. 2 or Shell Alvania R3		-30°C to 120°C	2.74 oz (81 ml)	End bearing lubricant; grease equally divided between bearing, bearing cap cavity and bearing cartridge cavity.
Other	DEF (diesel exhaust fluid), if equipped				Pre-start check: DEF tank filled to normal full level; auxiliary DEF system properly connected if equipped.
Other	Donaldsons D1400 solvent				Soak air cleaner filter element at least 15 minutes in water and D1400 solvent to remove soot, carbon and dirt

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Fault codes

Code	Name	Meaning	Severity	Action
101	IDLE MODE	Indicates that the engine is operating in idle mode. Grounding the engine idle input causes generator build-up to be inhibited and the engine to be governed at 800 RPM.	Warning	Remove ground from engine idle input to return to normal speed and voltage.
102	EMERGENCY STOP	Local or remote Emergency Stop; engine shuts down and will not crank	Shutdown	Turn the switch clockwise and allow it to pop out (local only); move the Run/Off/Auto switch to Off; press the Reset switch; select Run or Auto as required. Can be reset only at the PCC front panel.
111	Internal ECM error	Internal ECM error	Shutdown
1117	ECM POWER LOST	Battery voltage supply to the engine control module was lost.	Warning	Press Stop, then Emergency Stop, wait 30 seconds; re-set Emergency Stop and select an operating mode.
1118		Prelube relay driver	Warning
112	Actuator not responding	Category A	Shutdown
1121		Failed to Disconnect	Warning
1122	Rated/Idle Trans		Info
1123	Shutdown After Battle Short	A shutdown fault occurred while Battle Short was enabled and Battle Short transitioned from enabled to disabled	Warning	Review the Fault History and perform corrective action
1124	Delayed Shutdown	Provides advanced warning of an impending generator set shutdown to loads which cannot handle sudden power loss	Warning	A shutdown fault is present; review fault history
113	Actuator sensor fault	Category B	Warning
1131	Battle Short Active	Control is in Battle Short mode - bypasses several fault shutdowns during emergencies.	Warning	Battle short function enabled
115	No speed signal	No speed signal	Shutdown
116	Time press sensor high	Time press sensor high	Shutdown
117	Time press sensor low	Time press sensor low	Shutdown
118	Pump press sensor high	Pump press sensor high	Warning
119	Pump press sensor low	Pump press sensor low	Warning
121	Speed Signal Lost	No magnetic pickup pulses sensed for a Loss of Speed delay.	Warning
1219		Utility CB tripped	Warning
122	Manifold air press sensor	Manifold air press sensor	Warning
1222		Power transfer not in auto	Warning
1223		Utility frequency sensor	Warning
1224		Gen over voltage sensor	Warning
1225		Gen under voltage sensor	Warning
1226		genset frequency sensor	Warning
123	Manifold air press sensor	Manifold air press sensor	Warning
1245	CAN - Engine Shutdown	The PCC received a shutdown message from the ECM	Shutdown	Refer to the E-Controls service tool and the engine service manual
1246	GENERIC ENGINE FAULT	The PCC received an unknown message from the ECM	Warning	Refer to the E-Controls service tool and the engine service manual
1247	CAN - Engine Unannounced Fault	The PCC received an unknown message from the ECM	Warning	Refer to the E-Controls service tool and the engine service manual
1248	CAN - Engine Warning Fault	The PCC received an unknown message from the ECM	Warning	Refer to the E-Controls service tool and the engine service manual
1311	Customer input #1	Optional customer-selected fault, e.g. Low Fuel Day Tank, Water In Fuel, Ground Fault, Low Starting Hydraulic/Air Pressure		Programmable via service tool: enable/disable, status/warning/shutdown, active closed/open, custom display name
1311, 1312, 1317, 1318	Customer Input	Nature of the fault is an optional customer selection		Disconnect signal lead from TB1 (CUST_IN1 TB1-4, CUST_IN2 TB1-5, CUST_IN3 TB1-6, CUST_IN4 TB1-7) and reset the control; if the message clears, external wiring has a short/open or the active input selection (closed/open) is not correct
1312	Customer input #2	Optional customer-selected fault		Customer defined fault; message editable by the customer; can be programmed to initiate a shutdown or warning.
1313	Network Fault 1 thru 4	Network Fault 1		Customer defined fault; message editable by the customer; can be programmed to initiate a shutdown or warning.
1313-1316	Network Fault 1 Through 4	Indicates network input (#1-#4) is in an active state		Each fault function can be programmed (using the service tool) as Status, Warning, or Shutdown; change display name using up to 19 characters
1314	Network Fault 2	Network Fault 2		Customer defined fault; message editable by the customer; can be programmed to initiate a shutdown or warning.
1315	Network Fault 3	Network Fault 3		Customer defined fault; message editable by the customer; can be programmed to initiate a shutdown or warning.
1316	Network Fault 4	Network Fault 4		Customer defined fault; message editable by the customer; can be programmed to initiate a shutdown or warning.
1317	Customer input #3	Customer input #3		Customer defined fault; message editable by the customer; can be programmed to initiate a shutdown or warning.
1318	Customer input #4	Customer input #4		Customer defined fault; message editable by the customer; can be programmed to initiate a shutdown or warning.
1319	High alternator temp	High alternator temp	Warning
1321	Common warning driver	Common warning driver	Warning
1322	Load gov kW setpoint oor hi	Load gov kW setpoint oor hi	Shutdown
1323	Load gov kW setpoint oor lo	Load gov kW setpoint oor lo	Shutdown
1324	Load gov kVAR oor hi	Load gov kVAR oor hi	Warning
1325	Load gov kVAR oor lo	Load gov kVAR oor lo	Warning
1326	Backup starter disconnect	Category B	Warning
1327	Load gov kW analog oor	Load gov kW analog oor	Shutdown
1328	Genset CB tripped	Genset CB tripped	Warning
1329	AVR DC power failure	Category B	Warning
1331	AVR driver shorted	Category A	Shutdown
1332	Manual switch oor lo	Manual switch oor lo	Shutdown
1333	Manual switch oor hi	Manual switch oor hi	Shutdown
1334	Critical scaler oor	Critical scaler oor	Shutdown	Correct the feature/calibration entered into the control
1335	Noncrit Scaler Out Of Range	Non critical scaler oor	Warning	Correct the feature/calibration entered into the control
1336	Cooldown complete	Cooldown complete	Shutdown
1337	No Message	Network wink	Info
1341	Load demand stop	Load demand stop	Shutdown
1342	Slot 0 card	Slot 0 card	Shutdown
1343	Slot 1 card	Slot 1 card	Shutdown
1344	Slot 2 card	Category A	Shutdown
1345	Slot 3 card	Slot 3 card	Shutdown
1346	Slot 4 incorrect	Slot 4 incorrect	Shutdown
1347	Slot 5 card	Category A	Shutdown
1348	Slot 6 card	Category A	Shutdown
1349	Slot 7 card	Category A	Shutdown
135	Oil pressure sensor	Oil pressure sensor output is out of range, high.	Warning	Verify fault simulation not enabled (InPower); inspect sensor and engine harness connector pins; use oil pressure sensor simulator to check control response, replace sensor if it responds; check P7-13, 17, 21 for short (>200k ohms OK) and open (10 ohms or less OK)
1351	Slot 4 / network enabled	Slot 4 / network enabled	Warning
141	Oil pressure sensor	Oil pressure sensor output is out of range, low.	Warning	Verify fault simulation not enabled; inspect sensor/harness connector pins; use simulator to check control response; check P7-13, 17, 21 short/open
1414	Run relay contact	Run relay contact	Warning
1415	Run relay driver	Run relay driver	Warning
1416	Fail to shutdown	Shutdown fault active but bypassed by Battle Short mode; set continues to run.	Warning	Status - indicates the Fault Bypass mode is enabled (used primarily by service personnel for troubleshooting). The genset ignores the majority of system shutdown faults.
1417	Powr Down Error	The control has failed to go to sleep	Warning	Possible base board fault
1419	Fuel rail driver	Fuel rail driver	Warning
1421	Timing rail driver #1	Timing rail driver #1	Warning
1422	Timing rail driver #2	Timing rail driver #2	Warning
1424	High side driver	High side driver	Warning
1427	Overspeed relay driver	Overspeed relay driver	Warning
1428	LOP shutdown relay driver	LOP shutdown relay driver	Warning
143	Pre-Low Oil Pressure	Low oil pressure	Warning	Verify fault simulation not enabled; check oil level, lines and filters; use oil pressure sensor simulator; check +5 VDC at sensor (E1-A) and at P7-21; use simulator to P7-13 (OP OUT) and P7-17 (OP COMM); isolate to harness or base board

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Procedures

Aligning Generator with Engine (Angular Alignment) adjustment

⚠ Accidental starting of the generator set during this procedure presents the hazard of severe personal injury or death.

Tools: Dial indicator, Shims

Disconnect the negative (-) battery cable(s) before beginning.
Fasten a dial indicator to the generator shaft or cooling fan with the sensing point on the capscrew head or flat surface of the drive disc at the bolt circle diameter.
Bar the engine over in a clockwise rotation as viewed from engine flywheel; do not allow it to roll back on compression.
Determine the total indicator reading (T.I.R.) as the sum of the maximum positive and negative dial indicator readings over one revolution.
Measure the distance from the center of the generator shaft to the indicator measuring point.
Measure the distance from the generator side of the flex discs to the center of the generator mounting bolt.
Compare the distances; multiply this ratio times one half the T.I.R. to approximate the amount of shims to remove or add.

Angular Alignment Procedure adjustment

⚠ Accidental starting of the generator set during this procedure presents the hazard of severe personal injury or death. Make sure to disconnect the negative (-) battery cable(s) before beginning.

Tools: Dial indicator, Wooden shims

Disconnect the negative (-) battery cable(s) before beginning.
Fasten a dial indicator to the generator shaft or cooling fan with sensing point on capscrew head or flat surface of drive disc at bolt circle diameter.
Bar the engine over in a clockwise rotation as viewed from engine flywheel; do not allow it to roll back on compression.
Record maximum positive and negative dial indicator readings as the engine completes one revolution.
T.I.R. equals the sum of the maximum positive and negative readings.
Maximum T.I.R. should not be more than .001 inch for each inch of radius.
Remove equal shims from under both generator mounting feet to lower the generator.

Angular Alignment Procedure (Generator to Engine) adjustment

⚠ Accidental starting during this procedure presents the hazard of severe personal injury or death.

⚠ Do not bar engine over by prying on fan blade.

Tools: dial indicator

Disconnect the negative (-) battery cable(s) before beginning.
Fasten a dial indicator to the generator shaft or cooling fan with sensing point resting on the drive disc capscrew head/flat surface at the bolt circle diameter.
Bar the engine over in a clockwise rotation as viewed from the engine flywheel; do not allow it to roll back on compression at the end of travel of each reading.
Record the total indicator reading (T.I.R.) as the sum of the maximum positive and negative dial indicator readings over one engine revolution.
Compare the measured T.I.R. to the maximum allowed (.001 in. per inch of radius from center of shaft to indicator axis); add or remove shims under the generator mounting feet to correct.

Axial Alignment Procedure adjustment

Tools: Dial indicator with holding device (magnetic base or clamp)

Fasten dial indicator holding device to skid base, engine block, or generator shell with magnetic base or clamp.
Position so the sensor point rests on the generator shaft hub.
Bar the engine over clockwise (viewed from engine flywheel) through a couple of rotations.
Record indicator readings in eight equally spaced points around the shaft diameter to provide a T.I.R.
To correct an out-of-tolerance T.I.R., remove capscrews connecting drive discs and flywheel.
Mark the drive discs and flywheel with respect to each other.
Rotate engine or generator so drive disc holes are repositioned 180 degrees from original location.
Reinstall drive disc capscrews and retorque; re-check shaft alignment.
If T.I.R. unchanged, rotate discs to 30, 60, or 90 degrees from original location.
If T.I.R. does not improve, inspect flywheel pilot and drive disc runouts.

Axial Alignment Procedure (Generator to Engine) adjustment

Tools: dial indicator

Fasten a dial indicator holding device to the skid base, engine block, or generator shell with the sensor point resting on the generator shaft hub.
Bar the engine over in a clockwise rotation through a couple of rotations, recording indicator readings at eight equally spaced points around the shaft diameter to obtain axial T.I.R.
Reduce the measured T.I.R. runout by one half if excessive vibration remains after angular alignment.

Bus Voltage Calibration (C) adjustment

⚠ Contacting hazardous voltage components can cause electrocution, resulting in severe personal injury or death.

⚠ Improper calibration or adjustment of the PowerCommand control can cause equipment malfunction or damage.

Tools: Calibrated RMS multimeter (Fluke models 87 or 8060A)

Display the Bus Voltage Calibration submenu.
With all gensets OFF, attach a calibrated voltmeter to TB1-A (L1) and TB1-B (L2) of the bus PT module.
Start another genset and allow it to reach normal operating speed and voltage; connect to the bus.
Calibrate the voltage reading for Bus Volts L1 so display matches the calibrated meter.
Shut the generator set OFF.
Repeat steps 2 through 5 for Bus Volts L2 and L3.
Exit menu to Save changes.

Fuel Transfer Pump Control AC Connections (240 VAC to 120 VAC Conversion) adjustment

⚠ The control is set up at the factory for connection to 240 VAC.

Remove the two jumpers between terminals TB1-6 and TB1-7 and connect one jumper between TB1-5 and TB1-6 and the other between TB1-7 and TB1-8.
Move selector switch S103 on the control PCB to the up position for 120 V.
On the control transformer, remove the two jumpers between terminals H2 and H3 and connect one jumper between H1 and H3 and the other between H2 and H4.
Attach a tag to the control box indicating the supply voltage.

Generator Mount Pre-load Adjustment adjustment

⚠ Accidental starting of the generator set during this procedure presents the hazard of severe personal injury or death. Disconnect the negative (-) battery cable(s) before beginning.

Tools: Two 1 3/4" T x 2" W x 6" L steel spacers, Adequate lifting device

Turn off and disconnect battery charger (if equipped).
Disconnect the negative (-) battery cable(s) to prevent accidental starting.
Unscrew bolt (Item 2) from skid but do not remove from either rear engine vibration isolator.
Loosen the three screws that secure the engine mount brackets to the engine.
Loosen but do not remove the hex nut (Item 1) from the M20 screw of the generator vibration isolators.
Lift the generator until mounting feet brackets are high enough to insert a 1 3/4 inch steel spacer under both stator foot brackets.
Insert spacers and lower the generator so full weight rests on the mounting foot brackets.
Make sure no gap is present between skid and lower mount of rear engine vibration isolators.
Tighten the three screws to secure the bracket to the engine to 190-200 ft-lbs (260-270 N-m).
Lift the generator to remove the two 1 3/4 inch steel spacers.
Start the threads of the rear engine vibration isolator bolts (Item 2) before lowering.
Lower the generator and tighten the two rear engine vibration isolator bolts to 270-330 ft-lbs (365-447 N-m).
Secure the generator foot brackets to the vibration isolators and tighten to 270-330 ft-lbs (365-447 N-m).

Genset Ammeter Display Calibration (B) adjustment

⚠ Contacting hazardous voltage components can cause electrocution, resulting in severe personal injury or death.

⚠ Improper calibration or adjustment of the PowerCommand control can cause equipment malfunction or damage.

Tools: Calibrated RMS multimeter (Fluke models 87 or 8060A)

Display the Current Calibration submenu.
With the genset OFF, attach a calibrated ammeter to L1.
Start the genset and allow it to reach normal operating speed.
Load the genset to maximum rated kVA at rated voltage.
Calibrate the reading for L1 current so display agrees with calibrated ammeter.
Repeat steps 2 through 5 for L2 and L3.
Exit menu to Save changes.

Genset Voltage Display Calibration (A) adjustment

⚠ Contacting hazardous voltage components can cause electrocution, resulting in severe personal injury or death.

⚠ Improper calibration or adjustment of the PowerCommand control can cause equipment malfunction or damage.

Tools: Calibrated RMS multimeter (Fluke models 87 or 8060A)

Display the Voltage Calibration submenu.
With the genset OFF, attach a calibrated voltmeter to the AC output from L1 to L2 (L1 to Neutral for single phase).
Start the genset and allow it to reach normal operating speed.
Calibrate voltage reading for L1 so display agrees with the calibrated voltmeter.
Shut the generator set OFF.
Repeat steps 2 through 5 for L2 and L3.
Exit menu to Save changes.

Governor Calibration Checks adjustment

Tools: Frequency meter or tachometer, Jumper wire

Start the generator set.
Adjust engine no-load speed to the desired allowable speed droop using the Run Speed potentiometer.
With no load, turn GAIN clockwise slowly until engine speed oscillates.
Reduce GAIN slowly counterclockwise until engine speed is stable.
Upset the governor by momentarily shorting terminals 7 and 10 on the governor control.
Apply and remove loads to check generator set response.

HC4-7 Axial Alignment Procedure adjustment

Tools: Dial indicator with magnetic base or clamp

Check only when an objectionable vibration is present.
Fasten dial indicator holding device to skid base, engine block, or generator shell with magnetic base or clamp.
Position sensor point on the generator shaft hub.
Bar the engine over in a clockwise rotation as viewed from engine flywheel through a couple of rotations.
Record indicator readings in eight equally spaced points around the shaft diameter.
Remove the capscrews connecting drive discs and flywheel and mark discs and flywheel.
Rotate engine or generator so drive disc holes are repositioned 180 degrees from original location.
Put capscrews back in and retorque. Recheck shaft alignment.
If runout unchanged, rotate discs to 30, 60 or 90 degrees from original location.
If T.I.R. does not improve, inspect flywheel pilot and drive disc runouts.

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Voltage reconnection

Voltage	Phase	Connection	Leads	Notes
		12 lead generator sets	Load wires are routed through the CTs	Reconnectable gensets (12 leads) have dual secondary CTs (3 pins); CT wire 2/3 to pin 2 (high voltage) or pin 3 (low voltage).
		6 lead generator sets	Generator output leads are routed through the CTs	Non-reconnectable gensets (6 leads) have single secondary CTs (2 pins).
		Cummins PowerCommand generic AC Reconnect Wiring Diagram 625-2755 (Rev. D) and 625-3100 (Rev. F)		Applies to models DFAA, DFAB, DFAC, DFBF, DFCB, DFCC, DFEB, DFEC, DFFB, DFGA, DFGB, DFJA, DFJB, DFJC, DFJD, DFLB, DFLC, DFLD, DFMB (625-2755) and models DFAA-DFMB plus DFCE, DFED, DQAA, DQAB, DQBA, DQBB (625-3100).
		U, V, W, N terminals (U,V,W = L1,L2,L3; N = L0)	Stranded load wires bolted to generator reconnection terminal block or circuit breaker lugs	Generators can be configured to the nameplate voltages as shown on the Reconnection Diagram decal attached to the backside of the control box cover; many voltages require reconfiguration of the generator output leads.
	A (U)	CT21	U load leads (A phase)	CT dot must face the generator; CT terminal 1 connects to metering circuit, terminal 2/3 to ground.
	B (V)	CT22	V load leads (B phase)	CT dot must face the generator; terminal 1 to metering circuit, terminal 2/3 to ground.
	C (W)	CT23	W load leads (C phase)	CT dot must face the generator; terminal 1 to metering circuit, terminal 2/3 to ground.
110/190	3		12	Full load current at Standby rating: 1901 A
110/220	3		12	Full load current at Standby rating: 1642 A
115/230	3		12	Full load current at Standby rating: 1571 A
120/208	3		12	Full load current at Standby rating: 1737 A
139/240	3		12	Full load current at Standby rating: 1505 A
220/380	3		12	Full load current at Standby rating: 951 A
230/400	3		12	Full load current at Standby rating: 903 A
240/416	3		12	Full load current at Standby rating: 868 A
255/440	3		12	Full load current at Standby rating: 821 A
277/480	3	Wye, 4 Wire	12	Full load current at Standby rating: 753 A
277/480	3	Wye, 4 wire	12	Alternator 60 Hz, 12 lead, limited range, 125 °C; single phase power may be taken at up to 40% of nameplate kW at unity power factor
347/600	3		12	Full load current at Standby rating: 602 A

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Parts cataloged across the Cummins/Onan QSX15 family

Part #	Description	Category
AF25544	Element, Primary - Air Cleaner - Fleetguard - Heavy Duty	Air filter
AF25545	Element, Safety - Air Cleaner - Fleetguard - Heavy Duty	Air filter
0908-0101	Lead Acid Battery	Battery
3375044	Torque Wrench	Belt
19802521	ECM Dataplate	ECM / ECU
3331096	Cummins, Part No. 3331096	Fuel filter
3376807	Fuel filter	Fuel filter
FS1007	Fleetguard® Nelson®, Part No. FS1007	Fuel filter
M-4376220	Juego Junta Superior N. ° de Pieza	Gasket
M-4376221	Juego Junta Inferior N. ° de Pieza	Gasket
3375049	Oil Filter Wrench	Oil filter
3406810	Combination Full-Flow/Bypass Lubricating Oil Filter Cummins Part No. 3406810	Oil filter
0908-0203	Operator manual	Operator manual
0908-0204	Operator manual	Operator manual
0908-0230	Generator Set Operator Manual	Operator manual
0179-3536	Coolant heater (Revision E)	Service part / kit
0402-0222	Vibration isolator (non-seismic rated, does not carry IBC/OSHPD certification)	Service part / kit
0402-0234	Vibration isolator (non-seismic rated, does not carry IBC/OSHPD certification)	Service part / kit
0402-0246	Vibration isolator (non-seismic rated, does not carry IBC/OSHPD certification)	Service part / kit
0402-0427	Vibration isolator (non-seismic rated, does not carry IBC/OSHPD certification)	Service part / kit
0908-0107	Radiator Information	Service part / kit
0908-0110	Health and Safety (Diesel Generator Sets)	Service part / kit
0908-0219	Alarm Module (option)	Service part / kit
17200015	Engine Shutdown	Service part / kit
17690172	Engine Braking System	Service part / kit
17800006	Engine Model	Service part / kit
3163156	Service cable for InPower™	Service part / kit
3822735	Plastic bead blasting media	Service part / kit
3886301	InPower™ electronic service tool	Service part / kit
A035H139	Switch, Pushbutton	Service part / kit
A040U808	Harness, Control − Door (Includes Items 30 & 31)	Service part / kit
A046Y204	Shield, Wiring	Service part / kit
CC2609	Fleetguard Water-Check H2O 3-Way Test Strips	Service part / kit
M-3685996	Intake Valve	Service part / kit
M-5473065	150mm Kit de Motor M-5473066	Service part / kit
M-5473069	152mm Kit de Motor M-5473070	Service part / kit
M-5473074	Kit de Motor M-5473075	Service part / kit
TB3-5	Generator Set Control Panel Terminal Block	Service part / kit
TB3-6	Generator Set Control Panel Terminal Block	Service part / kit
ol204vt	Torque Peak	Service part / kit
M-5473087	Piston Kit	Piston kit
M-5484414	Piston Pin	Piston pin
M-3686661	Valvula de escape - M-3686661	Valve

Parts cataloged across all variants of this engine family — verify the exact part fits your specific variant and serial number before ordering.

Common questions

What is the oil capacity of the Cummins/Onan QSX15-G9?

The Cummins/Onan QSX15-G9 engine has an oil capacity of 83.3 liters.

What is the displacement of the Cummins/Onan QSX15-G9?

The Cummins/Onan QSX15-G9 has a displacement of 14.9 liters with 6 cylinders.

Which generators use the Cummins/Onan QSX15-G9 engine?

The Cummins/Onan QSX15-G9 powers 13 generator set(s), including Cummins/Onan 350DFEG, Cummins/Onan 450 DFEJ, Cummins/Onan 500 DFEK, Cummins/Onan C450D6, Cummins/Onan DFE.

How often should you change the oil in the Cummins/Onan QSX15-G9?

The Cummins/Onan QSX15-G9 oil change interval is every 8 hours.

What is a common problem with the Cummins/Onan QSX15-G9 engine?

A commonly reported issue on generators using the Cummins/Onan QSX15-G9 is: Over Current.