Service parts for the MLT4060DOTK
Grouped by system, with how many of each the parts manual calls for.
Fuel system
1 requiredOil system
1 requiredPrices captured from merchant listings; some links are affiliate links. Confirm against your serial number before ordering.
Specifications
| Frequency | 60.0 Hz |
|---|---|
| Standby power | 9 kW |
| Standby kVA | 13 |
| Prime power | 6 kW |
| Emissions | 4f |
| Oil capacity | 3.8 L |
| Alternator | Marathon 201CSA5411 (Class F insulation) |
| Voltage options | 120/240 V |
| Phase | single phase |
| Rated current | 50 A |
| Power factor | 1 (1Ø) |
| Circuit breaker | 30 A |
| Battery group | 24 |
| Battery cranking | 440 CCA |
| Battery voltage | 12V V |
| Battery quantity | 1 |
| Dimensions (L×W×H) | 170×68×70 mm |
| Dry weight | 770 kg |
| Sound level | 70.0 dBA |
| Fuel tank | 114.0 L |
| Tank runtime | 60 hr |
Engine
| Oil capacity | 5.1 L |
|---|---|
| Coolant capacity | 4.5 L |
| Displacement | 1.0 L |
| Aspiration | naturally aspirated |
| Rated speed | 1800 rpm |
Maintenance & consumables
for the Kubota D1005-E3BG1-MGM-1| Item | Spec | Capacity | Part # | Interval | |
|---|---|---|---|---|---|
| Air filter | Replace the air filter element yearly, or after six cleanings, whichever occurs first. | — | 365 hr | ||
| Fuel filter | 33192 | 500 hr | Amazon eBay $24.95 | ||
| Oil filter | 7665025430 | 1000 hr | Amazon $18.01 eBay $22.12 PartsGeek $7.98 | ||
| Battery | Check the battery daily. | — | 24 hr | ||
| Belt | Replace Fan Belt | — | 1000 hr | ||
| Coolant | — | 24 hr | |||
| Oil | Change the engine oil and oil filter after the initial 50 hours of operation, then at the appropriate interval thereafter. | — | 1000 hr | ||
| Spark plug | Replace Air Filter Element | — | 1000 hr |
Compatible filters for the Kubota D1005-E3BG1-MGM-1 — cross-referenced via Donaldson. Options to verify against your serial number, not confirmed for this exact unit.
- Air filter: Kubota RG64842831 Kubota RG15842930 Kubota R141142289 Donaldson P628324 Donaldson P629467
Common questions
How many kW is the Generac MLT4060DOTK?
The Generac MLT4060DOTK is rated 9 kW standby (13.1 kVA).
What engine does the Generac MLT4060DOTK use?
The Generac MLT4060DOTK is powered by the Kubota D1005-E3BG1-MGM-1 engine.
What is the oil capacity of the Generac MLT4060DOTK?
The Kubota D1005-E3BG1-MGM-1 engine in the Generac MLT4060DOTK has an oil capacity of 5.1 liters.
What alternator does the Generac MLT4060DOTK use?
The Generac MLT4060DOTK uses a Marathon 201CSA5411 alternator. Insulation class F.
What oil filter does the Generac MLT4060DOTK use?
The Generac MLT4060DOTK uses oil filter part number 7665025430.
Which fuel filter part number does the Generac MLT4060DOTK take?
The Generac MLT4060DOTK uses fuel filter part number 33192.
Which air filter part number does the Generac MLT4060DOTK take?
The Generac MLT4060DOTK uses air filter part numbers KUBOTA RG64842831, KUBOTA RG15842930.
Troubleshooting
3Symptoms & remedies
| Symptom | Cause | Remedy |
|---|---|---|
| Mast Lights Off, but Ballast Indicators on Control Panel are On. | Light fixture is too hot. Faulty lamp connection. Lamp broken Loose lighting connections Damaged or loose electrical cord | Allow light to cool 10-15 minutes before restarting. Check that the lamp is tight in the socket. Check for broken arc tube or outer lamp jacket, broken or loose components in lamp envelope, or blackening/deposits inside tube. Check the connections inside the mast junction box and each mast light housing/socket. Check the mast electrical cord for damage and check the cord connections inside the control box. |
| Mast Lights Off, and Ballast Indicators on the Control Panel are Off. | Loose lighting connections Generator output incorrect. Low transformer output. | Check the connections inside the control box and inside each ballast box. Check the incoming voltage to the ballast by checking the available voltage on the GFCI receptacle. Incoming voltage should be 120V +/- 5V. If voltage is incorrect, the engine speed may need to be adjusted or generator may require service. The voltage from the transformer should read approximately 400VAC as the light 'strikes' (induces an arc), then drop and slowly rise back up to stabilize at 240-260VAC. On hard wired models, remove the mast junction box cover and insert the wire probes into the connector blocks for the light and ground. If proper voltage is not achieved, perform capacitor check to determine if the capacitor or coil needs to be replaced. |
| Mast Lights On But the Light Output is Low | Fixture and/or lens is dirty. Lamp worn due to normal use Damaged or loose electrical connections Generator output incorrect. Low transformer output. | Check the incoming voltage to the ballast by checking the available voltage on the GFCI receptacle. Incoming voltage should be 120V +/- 5V. If voltage is incorrect, the engine speed may need to be adjusted or generator may require service. The voltage from the transformer should read approximately 400VAC as the light 'strikes' (induces an arc), then drop and slowly rise back up to stabilize at 240-260VAC. On hard wired models, remove the mast junction box cover and insert the wire probes into the connector blocks for the light and ground. If proper voltage is not achieved, perform capacitor check to determine if the capacitor or coil needs to be replaced. |
Fault codes and symptom→remedy steps extracted from this model’s service/owner documentation; verify against the official manual before servicing.
Parts
3| Part # | Description | Qty | System | |
|---|---|---|---|---|
| 90243 | Air Filter Element | Air filter | Amazon eBay | |
| 02076 | Unit ID Tag, Vin Tag | Service part / kit | Amazon eBay | |
| 209649 | Form: SFC626B | 1 | Service part / kit | Amazon eBay |
Service, wear & replacement parts referenced for this model and its engine — confirm the exact part for your serial number. See the full parts catalog to search and cross-reference.