Specifications
| Frequency | 60.0 Hz |
|---|---|
| Standby power | 9 kW |
| Standby kVA | 13 |
| Prime power | 6 kW |
| Emissions | 4F |
| Oil capacity | 5.4 L |
| Alternator | Marathon 201CSA5411 |
| Voltage options | 120/240 V |
| Phase | 1 |
| Rated current | 50 A |
| Power factor | 1 (1Ø) |
| Circuit breaker | 30 A |
| Battery group | 24 |
| Battery cranking | 440 CCA |
| Battery voltage | 12V V |
| Battery quantity | 1 |
| Dimensions (L×W×H) | 3000×2800×1750 mm |
| Dry weight | 774 kg |
| Sound level | 70.0 dBA @ 23 m |
| Fuel tank | 114.0 L |
| Tank runtime | 72 hr |
Engine
| Oil capacity | 3.6 L |
|---|---|
| Coolant capacity | 4.5 L |
| Displacement | 1.0 L |
| Aspiration | Diesel, liquid cooled, 4-stroke |
| Rated speed | 1800 rpm |
Maintenance & consumables
for the Kubota D1005-E3BG1-MGM-1| Item | Spec | Capacity | Part # | Interval | |
|---|---|---|---|---|---|
| Air filter | Replace the air filter element yearly, or after six cleanings, whichever occurs first. | — | 1000 hr | find | |
| Fuel filter | Clean fuel filter and replace the fuel filter cartridge after the initial 50 hours of operation, then at the appropriate interval thereafter. | — | 1000 hr | find | |
| Oil filter | 7665025430 | 1000 hr | PartsGeek | ||
| Belt | Check the fan belt tightness daily. Replace the belt according to the manufacturer’s recommendations. | — | 1000 hr | find | |
| Coolant | Check coolant level daily by inspecting the level in coolant overflow jug located near the radiator. Refer to the engine operator’s manual for coolant recommendations and proper mixture. | — | 12000 hr | ||
| Coolant filter | — | 250 hr | find | ||
| Oil | Change the engine oil and oil filter after the initial 50 hours of operation, then at the appropriate interval thereafter. | 6.7 | — | 1200 hr |
Compatible filters for the Kubota D1005-E3BG1-MGM-1 — cross-referenced via Donaldson. Options to verify against your serial number, not confirmed for this exact unit.
- Air filter: Kubota RG64842831 Kubota RG15842930 Kubota R141142289 Donaldson P628324 Donaldson P629467
- Fuel filter: Donaldson P551039
Common questions
What is the power rating of the Generac MLT3060KV?
The Generac MLT3060KV is rated 9 kW standby (13.1 kVA).
What engine does the Generac MLT3060KV use?
The Generac MLT3060KV is powered by the Kubota D1005-E3BG1-MGM-1 engine.
What is the oil capacity of the Generac MLT3060KV?
The Kubota D1005-E3BG1-MGM-1 engine in the Generac MLT3060KV has an oil capacity of 3.6 liters.
What alternator does the Generac MLT3060KV use?
The Generac MLT3060KV uses a Marathon 201CSA5411 alternator.
Troubleshooting
22Symptoms & remedies
| Symptom | Cause | Remedy |
|---|---|---|
| Low oil pressure shutdown | Low oil level | Verify oil level on dipstick. Add oil, if needed. |
| Oil leaking from engine | Visually inspect the engine for leaks. | |
| Oil pressure switch failure | Refer to OEM engine operator’s manual to identify corrective action. | |
| High coolant temperature shutdown | Low coolant level | Add coolant if needed. Allow engine to cool, then check coolant level in radiator. Restart engine and check coolant temperature. Stop engine immediately if coolant temperature is 210°F (99°C) or more. |
| Unit cranks, but will not start | Fuel level low | Check fuel level in tank. Verify fuel pump operation. |
| Mast Lights Off, but Ballast Indicators on Control Panel are On. | Light fixture is too hot. Faulty lamp connection. Lamp broken | Allow light to cool 10-15 minutes before restarting. Check that the lamp is tight in the socket. Check for broken arc tube or outer lamp jacket, broken or loose components in lamp envelope, or blackening/deposits inside tube. |
| Mast Lights Off, and Ballast Indicators on the Control Panel are Off. | Loose lighting connections. Generator output incorrect. Low transformer output | Check the connections inside the control box and inside each ballast box. Check the incoming voltage to the ballast by checking the available voltage on the GFCI receptacle. Incoming voltage should be 120V +/- 5V. If voltage is incorrect, the engine speed may need to be adjusted or generator may require service. |
| Mast Lights On But the Light Output is Low | Fixture and/or lens is dirty. Lamp worn due to normal use. Damaged or loose electrical connections. Generator output incorrect. Low transformer output | Clean reflective surface inside fixture and both inside and outside surface of glass lens. Use mild soap and water to clean lens. Other chemicals may have an adverse effect on the glass. Replace lamp. Check the mast coil cord, mast junction box and mast light connections. |
| Engine starting issues | Faulty glow plugs | Check glow plugs |
| Engine oil and filter need replacement | Replace engine oil and oil filter | |
| Engine oil and filter need replacement after initial 50 hours of operation | Change the engine oil and oil filter after the initial 50 hours of operation, then at the appropriate interval thereafter. | |
| Air cleaner element needs replacement | Replace air filter element yearly, or after six cleanings, whichever occurs first. | |
| Engine oil and filter need replacement annually | Replace air filter element yearly, or after six cleanings, whichever occurs first. | |
| Mast lights off but ballast indicators on control panel are on | 1. Mast light is too hot. Allow light to cool 10-15 minutes before restarting. 2. Faulty bulb connection. Check that the bulb is tight in the socket. 3. Bulb broken. Check for broken arc tube or outer bulb jacket, broken or loose components in bulb envelope or blackening/deposits inside tube. 4. Check the connections inside the mast junction box and each mast light housing/socket. 5. Check the mast electrical cord for damage and check the cord connections inside the control box. | |
| Mast lights off and ballast indicators on control panel are off | 1. Check the connections inside the control box and inside each ballast box. 2. Generator output incorrect. Check the incoming voltage to the ballast by checking the available voltage on the duplex receptacle. Incoming voltage should be 120V +/- 5V. If voltage is incorrect, the engine speed may need to be adjusted or generator may require service. 3. Low transformer output. The voltage from the transformer should read approximately 400 VAC as the light “strikes” (induces an arc), then drop and slowly rise back up to stabilize at 240-260 VAC. On quick disconnect models, measure across the junction box terminals when the light is unplugged. On hard wired models, remove the mast junction box cover and insert the wire probes into the connector blocks for the light and ground. If proper voltage is not achieved, perform capacitor check to determine if the capacitor or coil needs to be replaced. | |
| Mast lights OFF but ballast indicators ON | Light fixture is too hot | Allow light to cool 10–15 minutes before restarting. |
| Mast lights OFF and ballast indications OFF | Loose lighting connections | Check the connections inside the control box and inside each ballast box. |
| Generator output incorrect | Check the incoming voltage to the ballast by checking the available voltage on the GFCI receptacle. Incoming voltage should be 120V ±5V. | If voltage is incorrect, the engine speed may need to be adjusted or generator may require service. |
| Low transformer output | The voltage from the transformer should read approximately 400VAC as the light “strikes” (induces an arc), then drop and slowly rise back up to stabilize at 240–260VAC. On hard wired models, remove the mast junction box cover and insert the wire probes into the connector blocks for the light and ground. If proper voltage is not achieved, perform capacitor check to determine if the capacitor or coil needs to be replaced. | |
| Mast lights ON but power output is low | Fixture and/or lens is dirty | Clean reflective surface inside fixture and both inside and outside surface of glass lens. Use mild soap and water to clean lens. Other chemicals may have an adverse effect on the glass. |
| Blockage in radiator | Inspect radiator shroud and ducting for blockage and remove any foreign matter. | |
| Leakage in coolant hoses, engine block, or water pump | Inspect for visible leaks. Verify tension of water pump serpentine drive belt. |
Fault codes and symptom→remedy steps extracted from this model’s service/owner documentation; verify against the official manual before servicing.
Parts
72| Part # | Description | Qty | System | |
|---|---|---|---|---|
| 00120 | Belt | Belt | PartsGeek | |
| 00147 | CONTROL POWER SWITCH | Control power switch | PartsGeek | |
| 00161 | WING NUT | Wing nut | PartsGeek | |
| 00202 | GLOW PLUG | Glow plug | PartsGeek | |
| 00203 | GLOW PLUG | Glow plug | PartsGeek | |
| 003574 | Quick Disconnect Fittings for the Lights | Quick disconnect fittings | PartsGeek | |
| 003787 | Unit Dimensions | 1 | Unit dimensions | PartsGeek |
| 003788 | Component Locations | 1 | Component locations | PartsGeek |
| 003791 | GLOW PLUG OFF | 1 | Glow plug | PartsGeek |
| 003793 | GLOW PLUG | 1 | Glow plug | PartsGeek |
| 004478 | GLOW PLUG INDICATOR, RUN, START, GLOW PLUG A, B, C | 2 | Spark plug | PartsGeek |
| 004481 | Wheel Lug | Wheel lug | PartsGeek | |
| 004548 | Glow Plug Indicator | 1 | Glow plug | PartsGeek |
| 004558 | Winch Motor Assembly | 2 | Pump | PartsGeek |
| 11199 | Seal, axle bearing | 2 | Seal | PartsGeek |
| 12227 | Hose, oil drain .375 X 20, 30R7 | 1 | Hose | PartsGeek |
| 12441 | Cable, battery - 31.5" 4GA blk (for batt disc. opt.) | 1 | Cable | PartsGeek dieselpartscenter $2.61 |
| 12442 | Cable, battery - 58.5" 2GA blk (for batt disc. opt.) | 1 | Cable | PartsGeek |
| 13876 | Kit, heater - fuel filter | 1 | Fuel filter | PartsGeek |
| 60777 | Clamp, hose - .312 fuel hose crimp style | 1 | Hose | PartsGeek |
| 65649 | Heater, engine - low rad hose | 1 | Hose | PartsGeek |
| 90243 | Oil Filter Cartridge | Oil filter | PartsGeek | |
| 000265 | Film of grease on the coupler will extend coupler life and eliminate squeaking. | Service part / kit | PartsGeek | |
| 000277 | WARNING: Burn hazard. Never operate lights with a damaged or missing lens cover. | Service part / kit | PartsGeek | |
| 000278 | WARNING: Burn hazard. Lamps become extremely hot while in use. Allow 10–15 minutes for cooling before handling or lowering mast. | Service part / kit | PartsGeek | |
| 002306 | needle nose applicator | 1 | Service part / kit | PartsGeek |
| 00232 | Towing Unit - Step 10 | Service part / kit | PartsGeek | |
| 00243 | Grease | Service part / kit | PartsGeek | |
| 00246 | Safety alert symbol; used to alert you to potential personal injury hazards. | Service part / kit | PartsGeek | |
| 00325 | FUEL FILLER LOCATION (under door): Use clean DIESEL FUEL ONLY. | Service part / kit | PartsGeek | |
| 00326 | STOP EMERGENCY STOP SWITCH: For emergency shutdown; stops engine and trips main circuit breaker. | Service part / kit | PartsGeek | |
| 00327 | DETAIL C: For emergency shutdown; stops engine and trips main circuit breaker. | Service part / kit | PartsGeek | |
| 00328 | DETAIL D: For emergency shutdown; stops engine and trips main circuit breaker. | Service part / kit | PartsGeek | |
| 003754 | WARNING: Burn hazard. Lamps become extremely hot while in use. Allow 10–15 minutes for cooling before handling or lowering mast. Touching a hot lens or fixture can cause severe burns. | Service part / kit | PartsGeek | |
| 003792 | RUN START | 1 | Service part / kit | PartsGeek |
| 003794 | RUN START | 1 | Service part / kit | PartsGeek |
| 003985 | B C C A | Service part / kit | PartsGeek | |
| 004477 | Flagger Station Switches | 2 | Service part / kit | PartsGeek |
| 004480 | grease cap | Service part / kit | PartsGeek | |
| 004490 | WARNING: Burn hazard. Lamps become extremely hot while in use. Allow 10–15 minutes for cooling before handling or lowering mast. Touching a hot lens or fixture can cause severe burns. | Service part / kit | PartsGeek | |
| 004550 | WARNING: Burn hazard. Lamps become extremely hot while in use. Allow 10–15 minutes for cooling before handling or lowering mast. Touching a hot lens or fixture can cause severe burns. | 1 | Service part / kit | PartsGeek |
| 004551 | Equipment Damage. Failure to perform a daily inspection could result in damage to the unit. | Service part / kit | PartsGeek | |
| 004553 | VIN Tag | 1 | Service part / kit | PartsGeek |
| 004559 | CAUTION | 1 | Service part / kit | PartsGeek |
| 004561 | Unit ID Tag | 1 | Service part / kit | PartsGeek |
| 004563 | I O I O I O I O | Service part / kit | PartsGeek | |
| 00768 | Mast Junction Box Wiring and Light Connections | 1 | Service part / kit | PartsGeek |
| 02076 | Unit ID Tag, Vin Tag | Service part / kit | PartsGeek | |
| 11253 | Cap, grease - axis with rubber plug 3500# | 2 | Service part / kit | PartsGeek |
| 11254 | Plug, grease cap - for zerk (Axis) | 2 | Service part / kit | PartsGeek |
| 11275 | Decal, Magnum logo w/ web - red vinyl | 1 | Service part / kit | PartsGeek atldiesel $28.53 |
| 11277 | U-bolt, axle | 4 | Service part / kit | PartsGeek |
| 11278 | Tie plate, spring | 2 | Service part / kit | PartsGeek FridayParts $5489.60 |
| 11279 | Nut, locking | 8 | Service part / kit | PartsGeek |
| 11280 | Spring, axle | 2 | Service part / kit | PartsGeek |
| 11555B | Weldment, removable tongue - 74" | 1 | Service part / kit | PartsGeek |
| 12140 | Decal set, common mast 4-lang | 1 | Service part / kit | PartsGeek kuduparts $8.00 |
| 12141 | Decal set, LT eng/safety 4-lang | 1 | Service part / kit | PartsGeek |
| 12207 | Axle, 3500 lb. 56SC 68.5TC | 1 | Service part / kit | PartsGeek |
| 12262 | Decal, 4000/5000 set up 4-lang (manual winch) | 1 | Service part / kit | PartsGeek |
| 12880 | Decal, instruction 4000/5000 4-lang (electric winch) | 1 | Service part / kit | PartsGeek |
| 12881 | Decal, instruction 3000 4-lang (EW) | 1 | Service part / kit | PartsGeek |
| 13614 | Decal, mast junction box wiring - 4 light (for units with 2, 3 & 5 pos. locking terminal blocks) | 1 | Service part / kit | PartsGeek dieselpartscenter $0.58 |
| 15540 | Wheel, P205X75R15 radial w/rim | 2 | Service part / kit | PartsGeek |
| 15546 | Oil heater, pan - magnetic | 1 | Service part / kit | PartsGeek |
| 15547 | Blanket, battery for 24 series | 1 | Service part / kit | PartsGeek |
| 209649 | Form: SFC626B | 1 | Service part / kit | PartsGeek |
| 36431 | SERVICE LOG | Service part / kit | PartsGeek | |
| 40954 | Bearing, axle (inner) | 2 | Service part / kit | PartsGeek |
| 60096 | Lug Nut, .500-20 (incl. w/axle) | 10 | Service part / kit | PartsGeek |
| 60674 | Wheel stud, axle | 10 | Service part / kit | PartsGeek |
| 60766 | Valve, drain 18MM-1.5 w/nipple | 1 | Service part / kit | PartsGeek |
Service, wear & replacement parts referenced for this model and its engine — confirm the exact part for your serial number. See the full parts catalog to search and cross-reference.
Fuel consumption
| Rating | Load | L/h | gal/h |
|---|---|---|---|
| Prime | |||
| Standby |
Available documents
Owner's manual — 10000045550 (Generac)Owner's manual — 34098 (Generac)Owner's manual — MLT3060MV (Operation) (Generac)Service manual — 7542 MLT3060MV om 5 2017 (Generac)