Generac MLT Light Tower troubleshooting: 23 symptom-cause-remedy entries from the manufacturer's own service documentation.
Generac MLT Light Tower — full specs, parts & maintenance.
| Symptom | Cause | Remedy |
|---|---|---|
| Low oil pressure shutdown | Low oil level | Verify oil level on dipstick. Add oil, if needed. |
| Low oil pressure shutdown | Oil leaking from engine | Visually inspect the engine for leaks. |
| Low oil pressure shutdown | Oil pressure switch failure | Refer to OEM engine operator's manual to identify corrective action. |
| High coolant temperature shutdown | Low coolant level | Add coolant if needed. Allow engine to cool, then check coolant level in radiator. Restart engine and check coolant temperature. Stop engine immediately if coolant temperature is 210°F (99°C) or more. |
| High coolant temperature shutdown | Blockage in radiator | Inspect radiator shroud and ducting for blockage and remove any foreign matter. |
| High coolant temperature shutdown | Leakage in coolant hoses, engine block, or water pump | Inspect for visible leaks. Verify tension of water pump serpentine drive belt. |
| Unit cranks, but will not start | Fuel level low | Check fuel level in tank. Verify fuel pump operation. |
| Unit cranks, but will not start | Restricted air filter | Inspect air filter for blockage. Refer to OEM engine operator's manual for additional information. |
| Mast Lights Off, but Ballast Indicators on Control Panel are On. | Light fixture is too hot. | Allow light to cool 10-15 minutes before restarting. |
| Mast Lights Off, but Ballast Indicators on Control Panel are On. | Faulty lamp connection. | Check that the lamp is tight in the socket. |
| Mast Lights Off, but Ballast Indicators on Control Panel are On. | Lamp broken | Check for broken arc tube or outer lamp jacket, broken or loose components in lamp envelope, or blackening/deposits inside tube. |
| Mast Lights Off, but Ballast Indicators on Control Panel are On. | Loose lighting connections | Check the connections inside the mast junction box and each mast light housing/socket. |
| Mast Lights Off, but Ballast Indicators on Control Panel are On. | Damaged or loose electrical cord | Check the mast electrical cord for damage and check the cord connections inside the control box. |
| Mast Lights Off, and Ballast Indicators on the Control Panel are Off. | Loose lighting connections | Check the connections inside the control box and inside each ballast box. |
| Mast Lights Off, and Ballast Indicators on the Control Panel are Off. | Generator output incorrect. | Check the incoming voltage to the ballast by checking the available voltage on the GFCI receptacle. Incoming voltage should be 120V +/- 5V. If voltage is incorrect, the engine speed may need to be adjusted or generator may require service. |
| Mast Lights Off, and Ballast Indicators on the Control Panel are Off. | Low transformer output. | The voltage from the transformer should read approximately 400VAC as the light "strikes" (induces an arc), then drop and slowly rise back up to stabilize at 240-260VAC. On hard wired models, remove the mast junction box cover and insert the wire probes into the connector blocks for the light and ground. If proper voltage is not achieved, perform capacitor check to determine if the capacitor or coil needs to be replaced. |
| Mast Lights On But the Light Output is Low | Fixture and/or lens is dirty. | Clean reflective surface inside fixture and both inside and outside surface of glass lens. Use mild soap and water to clean lens. Other chemicals may have an adverse effect on the glass. |
| Mast Lights On But the Light Output is Low | Lamp worn due to normal use | Replace lamp. |
| Mast Lights On But the Light Output is Low | Damaged or loose electrical connections | Check the mast coil cord, mast junction box and mast light connections. |
| Mast Lights On But the Light Output is Low | Generator output incorrect. | Check the incoming voltage to the ballast. Incoming voltage should be 120V +/-5V. If the voltage is incorrect, the engine speed may need to be adjusted or the generator may require service. |
| Mast Lights On But the Light Output is Low | Low transformer output | The voltage from the transformer should read approximately 400VAC as the light "strikes" (induces an arc), then drop and slowly rise back up to stabilize at 240-260VAC. On hard wired models, remove the mast junction box cover and insert the wire probes into the connector blocks for the light and ground. If proper voltage is not achieved, perform capacitor check to determine if the capacitor or coil needs to be replaced. |
| Overspeed or Underspeed Shutdown | Frequency setting incorrect | Disconnect all loads and restart unit. Read frequency (Hz) in the LCD window on controller. Frequency should read 60 Hz. If frequency is above 60 Hz, engine speed will need to be adjusted. Refer to the engine operator's manual for throttle adjustment information. |
| Mast Lights Off, but Ballast Indicators on Control Panel are On. | Light fixture is too hot. Faulty lamp connection. Lamp broken Loose lighting connections Damaged or loose electrical cord | Allow light to cool 10-15 minutes before restarting. Check that the lamp is tight in the socket. Check for broken arc tube or outer lamp jacket, broken or loose components in lamp envelope, or blackening/deposits inside tube. Check the connections inside the mast junction box and each mast light housing/socket. Check the mast electrical cord for damage and check the cord connections inside the control box. |
Fault codes and symptom→remedy steps extracted from this model’s service/owner documentation; verify against the official manual before servicing.
Documented causes: Light fixture is too hot.; Faulty lamp connection.; Lamp broken; Loose lighting connections. See the table for the matching fixes.
Documented causes: Fixture and/or lens is dirty.; Lamp worn due to normal use; Damaged or loose electrical connections; Generator output incorrect.. See the table for the matching fixes.
Documented causes: Low oil level; Oil leaking from engine; Oil pressure switch failure. See the table for the matching fixes.