Home›Engines›Cummins/Onan QSK60-G19

Cummins/Onan QSK60-G19 Engine

The Cummins/Onan QSK60-G19 is an engine rated at 1800 rpm. It powers generator sets from Cummins/Onan, including the DQKAN.

Also known as: Cummins QSK60-G19

Part of the Cummins/Onan QSK60 engine family — 31 variants share parts & fitment.

1800 rpm

Rated speed

On this pageSpecs Generator sets FAQ Service intervals Torque & specs Fluids Fault codes Procedures Wiring

Engine specifications

Rated speed	1800 rpm

Generator sets powered by this engine

Cummins/Onan DQKAN

How to read your Cummins/Onan engine serial & model number →

Common problems

The control will not allow the starter to attempt to engage or to crank Cranking lockout
Cause: Not specified in text
Some shutdown faults are bypassed Battle short mode
Output power of the genset is reduced in response to a fault condition Derate
Indicates that engine temperature may not be high enough for a 10 second start or proper load acceptance Low coolant temperature warning
Cause: Engine temperature is low
Indicates status of battery charging system (failure) Low and high battery voltage warning
Cause: Continuously monitoring battery voltage
Emergency stop
Fix: Annunciated whenever either emergency stop signal is received from external switch.
Derate
Fix: The Derate function reduces output power of the genset in response to a fault condition. If a Derate command occurs while operating on an isolated bus, the control will issue commands to reduce the load on the genset via contact closures or Modbus. If a Derate command occurs while in utility parallel mode, the control will actively reduce power by lowering the base load kW to the derated target kW.
Control system indicates a fault if the genset fails to start by the completion of the engine crack sequence Fail to start (overcrank) shutdown
Cause: Genset fails to start
Control has signaled starter to crank engine but engine does not rotate Fail to crank shutdown
Cause: Engine does not rotate
Can be set up to be a warning or shutdown Low coolant level warning
Cause: Set up in control
Battle short mode
Fix: If a bypassed shutdown fault occurs, the fault code and description will still be annunciated, but the genset will not shutdown. This will be followed by a fail to shutdown fault.
Battery indicates impending failure Weak battery warning
Cause: Control system tests the battery each time the genset is signaled to start
Annunciated whenever either emergency stop signal is received from external switch Emergency stop

Compiled from service & troubleshooting documentation across every generator set that uses the Cummins/Onan QSK60-G19.

Service intervals

Item	Action	Hours	Months	Notes
Air cleaner restriction indicator	Check	8 hr		Daily 8 Hours; if indicator shows red, replace elements and reset indicator
Charge alternator	Check	8 hr		Daily 8 Hours
Control panel operation	Check	8 hr		Daily 8 Hours
Coolant level of radiator(s) (water jacket & LTA)	Check	8 hr		Daily 8 Hours
Crankcase breather tube/collector	Drain	8 hr		Daily 8 Hours; check for condensed oil
Emergency stop button operation	Test	8 hr		Daily 8 Hours; with genset running
Engine coolant heater	Check	8 hr		Daily 8 Hours
Engine oil level	Check	8 hr		Daily 8 Hours
Exhaust components and hardware	Check	8 hr		Daily 8 Hours
Fuel level in tank	Check	8 hr		Daily 8 Hours
Fuel system primary filter/water separator	Drain	8 hr		Daily 8 Hours; drain one cup or more
Air intake system (leaks)	Inspect	50 hr		Weekly 50 Hours
All hardware (fittings, clamps, fasteners)	Check	50 hr		Weekly 50 Hours
Coolant lines and radiator hoses	Check	50 hr		Weekly 50 Hours
Cooling fan blades	Inspect	50 hr		Weekly 50 Hours
Drive belt condition and tension	Check	50 hr		Weekly 50 Hours
Exhaust condensation trap	Drain	50 hr		Weekly 50 Hours
Fuel lines and hoses	Check	50 hr		Weekly 50 Hours; check before starting and again with genset running
Generator set enclosure	Check	50 hr		Weekly 50 Hours
Air cleaner housing	Clean	250 hr	6 mo
Anti-freeze and DCA concentration	Check	250 hr	12 mo
Battery electrolyte level	Check	250 hr	12 mo	Also at least every month or 100 hours of operation, whichever occurs first
Engine ground	Check	250 hr	6 mo	Clean as necessary
Engine/Alternator flexible rubber coupling	Inspect	250 hr	6 mo
Fuel system filters	Replace	250 hr	6 mo
Lubricating oil and filters	Change	250 hr	6 mo
Radiator air flow	Check	250 hr	6 mo
Radiator core	Clean	250 hr	12 mo	Schedule may be reduced depending on operating conditions/environment
Water separator element	Replace	250 hr	6 mo
Generator set fuel system filters (Single Fuel Filter)	Replace	1000 hr	12 mo
Bearings	Lubricate	1500 hr	12 mo	Re-grease bearings
Engine mounts	Check	1500 hr	12 mo
Pre-lube system (if fitted)	Check	1500 hr	12 mo	Check for leaks and cracks
Starting motor	Check	1500 hr	12 mo
Aftercooler core	Check	2000 hr	12 mo
Coolant filter	Change	2000 hr	12 mo
Coolant heater	Check	2000 hr	12 mo
Fan drive idler arm and fan belt tensioner	Check	2000 hr	12 mo
Turbocharger	Check	2000 hr	12 mo
Water pump	Check	2000 hr	12 mo

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Service specifications

Type	Item	Value	Unit	Condition
Other	Battery CCA (minimum)	2200	CCA	battery specification
Other	Battery electrolyte specific gravity charge threshold	1.215	SG	charge battery if reading is below
Other	Battery electrolyte specific gravity, fully charged	1.260	SG	corrected to 25 °C (77 °F)
Other	Water quality - Calcium, Magnesium (hardness) maximum	170	ppm (as CaCO3)	cooling system make-up water
Other	Water quality - Chloride maximum	40	ppm (as Cl)	cooling system make-up water
Other	Water quality - Sulfate maximum	100	ppm (as SO4)	cooling system make-up water
Speed	Default cranking/rest start cycle	15 seconds cranking, 30 seconds rest	seconds	default 3 start cycles
Speed	Idle speed range to avoid in cold ambient temperatures	650 to 1000	rpm	low operating temperatures
Temperature	Electrolyte temperature limit during boost charge	43	°C	boost charge
Temperature	Maximum permissible electrolyte temperature during charge	45	°C	during charge
Voltage	Boost charge battery volts limit (12 V battery)	15	V	boost charge; reduce charge rate if reached
Voltage	Starting system voltage	24	VDC	battery type specification

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Recommended fluids

Fluid	Grade	Standard	Notes
Coolant	50/50 mixture of high-quality water (distilled or deionized) and fully formulated antifreeze (ethylene glycol or propylene glycol); Fleetguard® coolant containing DCA4	Cummins Engineering Standard 14603	If not using Fleetguard Compleat antifreeze or equivalent, add DCA4
Engine oil	high-quality multi-viscosity lubricating oil (e.g. Cummins Premium Blue® or equivalent)		Consult authorized distributor for correct specification for operating conditions; special running-in oils not recommended
Fuel	ASTM No. 2D diesel, minimum Cetane number 40; alternative BS 2869:2010+A1:2011	ASTM No. 2D	Higher cetane numbers may be needed at high altitude or very low ambient temperature
Fuel	No. 2-D diesel	ASTM D975	40-48 cetane

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Fault codes

Code	Name	Meaning	Severity	Action
27	Low AC voltage shutdown	Voltage on any phase dropped below preset value; adjustable 50-95% of reference, 2-20 s delay, default 85% for 10 s	Shutdown	Shut down genset
32	Reverse power shutdown	Adjustable 5-20% of standby kW rating, 1-15 s delay, default 10% for 3 s	Shutdown	Shut down genset
40	Reverse Var shutdown	Adjustable 15-50% of rated Var output, 10-60 s delay, default 20% for 10 s	Shutdown	Shut down genset
46	Negative sequence overcurrent warning	Protects generator from damage due to excessive imbalances in three phase load currents and/or power factors	Warning	Warning alarm
51	Overcurrent warning/shutdown	Thermal damage curve with instantaneous trip based on CT ratio and application power rating	Shutdown	Shut down genset
51G	Ground fault overcurrent	Detects ground fault via external ground fault relay contact input or external current transformer; delays and thresholds adjustable	Shutdown	Shut down genset
59	High AC voltage shutdown	Output voltage on any phase exceeds preset values; adjustable 105-125% of nominal, 0.1-10 s delay, default 110% for 10 s	Shutdown	Shut down genset
81o	Over frequency shutdown/warning	Genset operating at damaging frequency; adjustable 2-10 Hz above nominal, 1-20 s delay, default 6 Hz for 20 s, disabled	Shutdown	Shut down genset
81u	Under frequency shutdown	Genset output frequency cannot be maintained; adjustable 2-10 Hz below reference, 5-20 s delay, default 6 Hz for 10 s	Shutdown	Shut down genset
111	Internal ECM Failure		Shutdown
115	Eng Crank Sensor Error		Shutdown
143	Low Oil Rifle Pressure	Engine oil pressure has dropped below the warning trip point.	Warning	If powering critical loads and cannot be shut down, wait until the next shutdown period and follow fault code 415 procedure.
144	High Coolant 1 Temp	Engine has begun to overheat and coolant temperature has risen to an unacceptable level.	Warning	Review fault code 151 correction list for other possible causes.
145	Low Coolant 1 Temp	Engine coolant temperature below the low coolant temperature warning threshold.	Warning	If powering critical loads and cannot be shut down, wait until next shutdown and follow fault code 1435 procedure.
146	Pre-High Engine Coolant Temperature	Engine operating near cooling system capacity.	Warning	Review fault code 151 correction list for other possible causes.
151	High Coolant Temp	Engine has overheated (coolant temperature above shutdown trip point or coolant level low).	Shutdown	Look for coolant leaks and repair; check and replenish coolant; check for cooling airflow obstructions; check fan belt; check blower fan and circulation pumps; reset and restart.
155	High Intake Manf 1 Temp	Intake manifold temperature has risen above the shutdown trip point; large load or high ambient temperature may be the cause.	Shutdown	Review fault code 151 correction list.
196	Low Coolant 1 Level	Engine coolant level has fallen below the trip point.	Warning	Look for coolant leaks and repair; check and replenish coolant; reset and restart.
197	Low Coolant Level	Engine coolant level has fallen below the trip point.	Warning	Look for coolant leaks and repair; check and replenish coolant; reset and restart.
234	Crankshaft Speed High	Overspeed - critical shutdown fault that suspends Battle Short mode.	Shutdown
235	Low Coolant Level	Low Coolant Level input active and threshold response set to Shutdown.	Shutdown	Look for coolant leaks and repair; check and replenish coolant; reset and restart.
359	Fail To Start	Possible fault with control or starting system (engine cranks but fails to start).	Shutdown	Check for empty fuel tank, leaks or blocked lines; check/replace dirty fuel filter; check/replace blocked air filter; clean and tighten battery connections; recharge or replace battery; reset and restart.
415	Low Oil Rifle Press	Engine oil pressure has dropped below the shutdown trip point.	Shutdown	Check oil level, lines and filters; replenish oil if low; reset and restart.
427	CAN Data Link Degraded	Communication between the engine control (ECM) and the PCC is severed.	Warning	Ensure the E-Stop button is not active; reset the Local/Remote Emergency Stop.
441	Low Battery 1 Voltage	Battery voltage below 24 VDC approaching a low level at which unpredictable operation will occur.	Warning	Clean battery terminals and tighten connections; check electrolyte level, top up and recharge; recharge or replace battery.
442	High Battery 1 Voltage	Battery voltage approaching a high level (exceeding 32 VDC) at which control damage can occur.	Warning	Clean battery terminals and tighten connections; check battery charge float level and lower if applicable.
488	High Intake Manf 1 Temp	Intake manifold temperature has risen above the shutdown trip point.	Derate	Review fault code 151 correction list.
611	Engine Hot Shut Down	An engine hot shutdown occurred (cooldown timers bypassed).	Warning	Avoid hot shutdown; run genset at 10% or less load for three minutes before shutdown.
781	CAN Data Link Failure	Communication between the engine control (ECM) and the PowerCommand 3.3 control severed.	Shutdown	Ensure the E-Stop button is not active; reset the Local/Remote Emergency Stop.
1131	Battle Short Active	Control is in Battle Short mode.	Warning	If possible, investigate any fault codes being bypassed.
1416	Fail To Shutdown	Records a bypassed shutdown fault while the genset was in Battle Short mode.	Warning	Troubleshoot the shutdown fault causing the generator set to shut down.
1433	Local Emergency Stop	A local Emergency Stop has been activated.	Shutdown	De-activate the Emergency Stop button; press Stop; press Reset; select desired operating mode.
1434	Remote Emergency Stop	A remote Emergency Stop has been activated.	Shutdown	De-activate the Emergency Stop button; press Stop; press Reset; select desired operating mode.
1435	Low Coolant Temperature	Engine coolant heater not operating or not circulating coolant; warning occurs when coolant temperature is 21 °C (70 °F) or lower.	Warning	Check coolant heater power supply, blown fuse or disconnected heater cable; check for coolant leaks; check and replenish coolant.
1438	Fail To Crank	Possible fault with control, speed sensing or starting system.	Shutdown	See code 441 for corrective action; ensure the Emergency Stop button is disengaged.
1439	Low Day Tank Fuel Switch	Day tank fuel supply running low.	Warning	Look for fuel leaks and repair; check and replenish fuel level.
1441	Low Fuel Level	Fuel level has gone below the threshold setting for low fuel level against the time setting.	Warning	Look for fuel leaks and repair; check and replenish fuel level.
1442	Weak Battery	During cranking the battery voltage is at or below the weak battery warning trip point.	Warning	See code 441.
1443	Dead Battery	During cranking the battery voltage dropped below the control operating voltage, resetting the control.	Shutdown	See code 441.
1445	Short Circuit		Shutdown
1446	High AC Voltage		Shutdown
1447	Low AC Voltage		Shutdown
1448	Under Frequency	Generator set frequency dropped below 90% of nominal for approximately ten seconds.	Shutdown	Check the fuel supply; check the air intake supply; check the load and correct any overload.
1449	Over Frequency	Generator set frequency exceeded the Over Frequency threshold for the set time.	Shutdown	Check the fuel supply; check the air intake supply; check the load and correct any overload.
1465	Ready To Load	Paralleling event indicating the genset is ready to load.	Info
1852	Pre-High H2O In Fuel	Water in the fuel is above normal and has reached the warning trip point.	Warning	Check fuel in tank (local or remote); drain and re-fill if necessary.
2335	AC Voltage Sensing Lost (Excitation Fault)	Loss of voltage sense - critical shutdown fault that suspends Battle Short mode.	Shutdown
2678	Charging Alternator Fail		Warning
2977	Low Coolant 2 Level	Engine coolant level in the second radiator has fallen below the trip point.	Warning	Look for coolant leaks and repair; check and replenish coolant; reset and restart.
3416	Start System Fault	Start system fault condition exists.	Warning	Refer to fault codes 359 and 1438.
5135	Genset Overload		Shutdown

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Procedures

Air Cleaner Installation installation

Use the two air filter straps to install a new air cleaner on the mounting platform.
Reinstall the hose clamp to secure the air cleaner to the hump hose.

Air Cleaner Removal maintenance

⚠ Holes, loose-end seals, dented sealing surfaces or corrosion render the air cleaner inoperative.

Loosen the hose clamp securing the air cleaner to the hump hose.
Remove the air cleaner and the two air filter straps from the mounting platform.
Remove the air filter straps from the air cleaner.
Dispose of the old air cleaner in accordance with local environmental requirements.

Crankcase Breather Oil Drain Cup maintenance

⚠ Avoid prolonged skin contact with used oil.

Tools: Suitable container

With the generator set not in operation, open the drain valve and drain oil into a suitable container.
Close the drain valve when completed.
Clean the area of any spills and dispose of waste per local regulations.

Engine Oil Level Check maintenance

⚠ Crankcase pressure can blow out hot oil; do not check oil while running.

Tools: Lint free cloth, Funnel (where possible)

Remove the dipstick and wipe it clean with a lint free cloth.
Fully replace the dipstick.
Remove the dipstick and check oil level against the High and Low marks.
Top up to the High mark with the correct grade of oil.
Replace the dipstick and oil filler cap.
Start the engine, idle for five minutes, switch off and wait five minutes.
Check oil level and repeat if oil needs to be added.

Fuel Filter Element Removal maintenance

⚠ Do not allow fuel to drain onto the ground.

⚠ Do not permit any open flame near the fuel system.

Tools: Collar/vent cap wrench, Suitable container

Shut down the engine.
Close the fuel supply shutoff valve.
Place a suitable container under the filter to be replaced.
Use the collar/vent cap wrench to open the vent cap and break the air lock.
Open the drain valve and drain fuel below the collar.
Close the drain valve.
Loosen the collar with the collar/vent cap wrench.
Remove the clear cover, filter spring, fuel filter element, o-ring and sealing grommet.

Fuel Filter Element Replacement maintenance

⚠ Do not permit any open flame near the fuel system.

Install a new o-ring, filter element (with sealing grommet), filter spring and clear cover.
Install the vent cap and collar onto the clear cover.
Hand tighten; do not use tools to tighten the collar.

Fuel/Water Separator Drain maintenance

⚠ Diesel fuel is a fire and explosion hazard.

⚠ Drained liquids must be disposed of per local environmental regulations.

Tools: Suitable container

Shut off the engine.
Place a suitable container under the fuel filter.
With the fuel supply valve closed, open the vent cap to break the airlock.
Turn the valve counterclockwise until it drops about 25 mm (1 in). Drain until clear fuel is visible.
Push the valve up and turn clockwise to close the drain valve.
Open the fuel supply valve before starting the engine.
If more than 60 ml (2 oz) is drained, refill the filter to prevent hard starting.

Immobilizing for Safe Working maintenance

⚠ Accidental or remote starting can cause severe personal injury or death.

Tools: Insulated wrench, Warning notices

Press the Off mode switch on the operator panel to shut down the generator set.
Press the Emergency Stop button to prevent starting from any source.
Thoroughly ventilate the plant room before disconnecting any leads.
Isolate and lock off the supply to the heater, where fitted.
Isolate and lock off the supply to the battery charger, where fitted.
Isolate the fuel supply to the engine.
Using an insulated wrench, disconnect the negative (–) battery cable first.
Fit warning notices to indicate Maintenance in Progress – Plant Immobilized.

Oil Sampling Valve maintenance

⚠ Contact with hot oil can cause severe burns; allow engine to cool before maintenance.

Tools: Oil sampling kit

Remove the cap from the sample bottle and attach the live sampling cap.
Remove the oil sampling drain valve cap from the valve.
With the engine running at normal operating temperature, screw the live sampling cap onto the drain valve.
Fill the sample bottle as directed by the sampling kit/laboratory instructions.
Remove the sample bottle and replace the valve cap.
Remove the live sampling cap from the sample bottle and replace the bottle cap; send for analysis.
Clean up any spillage per local regulations.

Emergency Stop Reset (Code 1433/1434) operation

⚠ Do not use the Emergency Stop button for normal shut-down; it prevents a cooling down run.

Pull, or twist and pull, the button out.
Press the Stop button on the operator panel to acknowledge.
Press the Reset button.
Press the Auto or Manual Run button as previously determined.

Starting at Operator Panel (Manual Run Mode) operation

⚠ Make sure all pre-start checks are carried out before starting.

⚠ Warn all others in the vicinity that the generator set is about to start.

Make sure the main circuit breaker is in the open position.
Press the Manual button, then press the Start button within ten seconds.
Allow the engine to warm up and reach rated speed and voltage.
Close the main circuit breaker and apply load as required.

Stopping at Operator Panel (Manual Mode) operation

⚠ Avoid hot shutdown under load to help prolong reliability.

Remove the load.
Open the main circuit breaker.
Press the stop button on the HMI operator panel to initiate cool down.
Once the cool down timer expires, the generator set shuts off and enters Off mode.

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Voltage reconnection

Voltage	Phase	Connection	Leads	Notes
12470	3	3 Ph Wye	6	Temp rise 105°C, Duty S, Max surge 11213 kVA, Winding No. 91, ADS-533, B568
13200	3	3 Ph Wye	6	Temp rise 105°C, Duty S, Max surge 11213 kVA, Winding No. 91, ADS-533, B501
13800	3	3 Ph Wye	6	Temp rise 80°C, Duty S, Max surge 11213 kVA, Winding No. 91, ADS-533, B610
240-208	single	240-208 volt connection		Coolant heater; for 240-208 volt move jumpers as shown
380	3	3 Ph Wye	6	Temp rise 105°C, Duty S, Max surge 13024 kVA, Winding No. 13, ADS-531, B408
416	3	3 Ph Wye	6	Temp rise 150°C, Duty S, Max surge 9719 kVA, Winding No. 12, ADS-517, B682
4160	3	3 Ph Wye	6	Temp rise 80°C, Duty S, Max surge 11185 kVA, Winding No. 51, ADS-545, B605
440	3	3 Ph Wye	6	Temp rise 105°C, Duty S, Max surge 13024 kVA, Winding No. 12, ADS-531, B664
480	3	3 Ph Wye	6	Temp rise 125°C, Duty S, Max surge 8412 kVA, Winding No. 12, ADS-516, B246
480	single	480 volt connection		Coolant heater; jumpers are factory installed in the 480 volt configuration
600	3	3 Ph Wye	6	Temp rise 125°C, Duty S, Max surge 8189 kVA, Winding No. 7, ADS-516, B602

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Parts cataloged across the Cummins/Onan QSK60 family

201

Part #	Description	Category
140-3288-02	Cleaner, Air	Air filter
140-3813	Element, Air Cleaner Primary	Air filter
140-3814	Element, Safety (Air Cleaner)	Air filter
140-3815	Cleaner, Air (Dust Ejector)	Air filter
140-3963	Cleaner, Air (Spec A-C Metal)	Air filter
AF25593	Element, Replacement (Spec A) (Fleetguard Part Number)	Air filter
AF25708M	Element, Replacement (Spec D-E) (Fleetguard Part Number)	Air filter
AF25750	Element, Replacement (Spec B-C) (Fleetguard Part Number)	Air filter
511-0161-17	Belt, V Ribbed	Belt
M-3649982	Juntade culata de cilindro - sobredimensionada 0,020" - M-3649982	Cylinder head盖板
QSK60	Gas engine	Engine
QSK60-G9	Engine model for C2500 D5A generator sets	Engine
QSK60G	Engine model QSK60G	Engine
4321098765	Fault Acknowledge Button	Fault acknowledge button
130-4546	Bracket, Mounting – Coolant Heater	Fluid
130-4552	Cover, Coolant Heater	Fluid
338-3335-01	Harness, Wiring – AC – Coolant Heater (From Coolant Heater Bottom To Coolant Heater Control Box) (Includes Conduit Connectors) (30”)	Fluid
338-3335-09	Harness, Wiring – AC – Coolant Heater (From Coolant Heater Bottom To Coolant Heater Control Box) (Includes Conduit Connectors) (108”)	Fluid
338-3831	Harness, Wiring – DC – Engine Heater (From Coolant Heater Control Box To Engine And Main Engine Harness) (Includes Parts Marked *)	Fluid
FS1006	Filter, Fuel Water Separator	Fuel filter
130-3684	Gasket	Gasket
130-5099	Gasket	Gasket
130-6405	Gasket, Radiator	Gasket
130-7145	Gasket, Radiator	Gasket
130-7232	Gasket, Radiator (4")	Gasket
130-7293	Gasket, Radiator (65NB)	Gasket
154-3182	Gasket, Flange (Fuel Line)	Gasket
155-3704	Gasket, Exhaust (10" BS Flange)	Gasket
155-4109	Gasket, Flange	Gasket
155-4601	Gasket, Exhaust	Gasket
155-4735	Gasket, Exhaust (10" ANSI Flange)	Gasket
186-6088	Plate, Valve Spring	Gasket
186-6090	Carrier, Valve Spring	Gasket
186-6091	Cotter, Valve	Gasket
186-6092	Guide, Valve	Gasket
186-6093	Seal, Valve Stem	Gasket
186-6109	Gasket, Cylinder Head	Gasket
186-6112	Gasket, Cylinder Head	Gasket
186-6436	Gasket, Cylinder Head	Gasket
186-6758	Valve, Inlet	Gasket
186-7004	Insert, Inlet Valve	Gasket
186-7005	Insert, Exhaust Valve	Gasket
186-7013	Head Assy, Cylinder	Gasket
186-7014	Head Assy, Cylinder	Gasket
186-7015	Head Assy, Cylinder	Gasket
319-3950	Gasket, Operator Panel	Gasket
319-3951	Gasket, Switch Panel	Gasket
330-0141-04	Gasket, Cover	Gasket
MCBQSK0045	Turbocharger Installation Kit	Gasket
MCBQSK0048	Water Pump Gasket Set	Gasket
MCBQSK0058	Water Pump Gasket Set	Gasket
128-0108	Insulation, Hose – Bulk (Order By The Foot – 12 Feet Required)	Hose
130-4885	Radiator (Includes Jacketwater, Aftercooler, Cap, Overflow Hose and Sight Gauge Sevice Parts) 130–3588	Hose
416-0680	Cable, Battery (10")	Hose
501-0838	Line, Fuel (DN80 Gas 500mm)	Hose
502-0656	Adapter, Male (1–5/16–12 Tubing to 1” Pipe)	Hose
502-0827	Fitting, Hose – Barbed (1/2” ID Pipe to 3/4” ID Hose)	Hose
502-0836	Fitting, Brass – Hose – Barbed (3/4” Pipe to 3/4” Hose)	Hose
502-1257	Connector, Hose – Barbed (Fits 3/4” ID Hose)	Hose
503-0189	Clamp, Hose	Hose
503-0249	Hose − Bulk (Order by the Foot − 3 Feet Required)	Hose
503-1136	Clamp, Hose	Hose
503-1418	Hose − Bulk (1/4” ID) (Order By The Foot − 18 Feet Required)	Hose
503-1634-01	Hose, Rubber (3/4” ID x 4”)	Hose
503-1726	Hose (5” ID x 6”)	Hose
503-1727	Hose, Radiator (3” ID x 10”)	Hose
503-1728	Hose (3” ID x 5–1/2”)	Hose
503-1745	Hose – Bulk – Front Grease Fitting (Order By The Foot – 2 Feet Required)	Hose
503-1863	Hose, Radiator (1–1/2” ID x 4”)	Hose
503-1872-01	Clamp, Hose	Hose
503-1872-05	Clamp, Hose	Hose
503-1872-09	Clamp, Hose (5” ID)	Hose
503-2204-06	Hose, Steam (19mm x 300)	Hose
503-2204-07	Hose, Steam (19mm x 800)	Hose
503-2204-08	Hose, Steam (19mm x 1000)	Hose
503-2204-09	Hose, Steam (19mm x 1700)	Hose
503-2518	Hose, Vent	Hose
505-1429	Nipple, Pipe – Combination (1–1/2” Pipe to 1–1/2” Hose)	Hose
505-2086	Nipple, Pipe (3/4)	Hose
505-2098	Nipple, Pipe (1/2)	Hose
518-0548-24	Clamp, Hose	Hose
518-0548-25	Clamp, Hose (3/8” ID)	Hose
0098-6074-02	Label, Warning	Label
098-2304	Label, Warning	Label
098-2304-01	Label, Warning	Label
098-4500	Decal	Label
098-4730	Label, Warning	Label
098-4732	Label, Warning	Label
098-4798	Label, Warning	Label
098-5347	Label, Danger	Label
098-5347-02	Label, Danger	Label
098-5759	Label, Warning	Label
098-5822	Label, Warning	Label
098-5842	Label, Caution	Label
098-6074-02	Label, Warning	Label
098-6195	Label, Caution	Label
098-6537	Label, Ground	Label
098-6650-01	Label, Danger	Label
098-6775	Label	Label
098-7614	Label, Warning	Label
098-7877	Label, Battery Warning	Label
098-7902-01	Label, Logo	Label
098-7902-03	Label, Logo	Label
098-7902-04	Label, Logo	Label
098-7904	Label, Danger	Label
098-8075	Label, Ground	Label
098-8144	Label, Information	Label
098-8204	Label, Warning	Label
098-8220	Label, Information	Label
098-8445	Label, Information	Label
098-8732-02	Label, Information	Label
098-8940	Label, Warning	Label
A029M832	Label, Warning	Label
A029S884	Label, Information	Label
A029Z072	Label, Information	Label
LF9050	Lube, Combination	Oil filter
0130-5997-05	Cummins Part No. 312/212, 37564; Cummins Part No. 312/212, 37604; Cummins Part No. 212, 37558; Cummins Part No. 212, 37614; Cummins Part No. 212, 37627; Cummins Part No. 313/312, 0179-2921; Cummins Part No. 313/312, 0179-2988; Cummins Part No. 312, 0179-3291; Cummins Part No. 312/212, 130-5791; Cummins Part No. 312/212, 37644; Cummins Part No. 312/212, 37624; Cummins Part No. 312/212, 37625; Cummins Part No. 212, 37648; Cummins Part No. 212, 37643; Cummins Part No. 212, 37678; Cummins Part No. 212, 37665; Cummins Part No. 312/212, 37676; Cummins Part No. 312/212, 37610; Cummins Part No. 313/212, 37642	Service part / kit
0179-2862	Nema 284T frame has the following arrangement: 6311 C3 / 18gram Polyrex – EM /20,000h	Service part / kit
0179-3291	Nema 284T frame has the following arrangement: 6311 C3 / 11gram Polyrex – EM /20,000h	Service part / kit
098-5387	Label, Danger	Service part / kit
130-5077-02	Tube, Heater	Service part / kit
130-5078-02	Tube, Heater	Service part / kit
130-5079-02	Tube, Heater	Service part / kit
130-5080-02	Tube, Heater	Service part / kit
130-5089-02	Tube, Heater	Service part / kit
155-4734	Flange, Exhaust (10" ANSI Flange)	Service part / kit
155-4736	Flange, Exhaust (10" BS Flange)	Service part / kit
186-6087	Valve, Exhaust	Service part / kit
186-6089	Part 186-6089	Service part / kit
3163156	Service cable for InPower™	Service part / kit
323-1491	* Pin, Contact (Used With Inline G)	Service part / kit
323-1492	* Socket, Contact (Used In Stations 18, 19)	Service part / kit
323-1688	* Socket, Contact (Used In P1)	Service part / kit
323-1718	* Pin, Contact (Used In Station 17)	Service part / kit
333-0634-02	Heater, Coolant - 6420 Watt	Service part / kit
3886301	InPower™ electronic service tool	Service part / kit
4-2002	PowerCommand Control	Service part / kit
416-1019	Boot, Battery (Red)	Service part / kit
504-0215	Valve, Check (1/4)	Service part / kit
504-0239	Valve, Ball (3/4)	Service part / kit
504-0247	Valve, Ball (1/2)	Service part / kit
504-0294	Valve, Ball (3 Way 2" DN80) - ANSI Flanges	Service part / kit
504-0295	Valve, Ball (3 Way 3" DN80) - ANSI Flanges	Service part / kit
504-0301	Valve, Ball (3 Way 2" DN80) - BS Flanges	Service part / kit
504-0302	Valve, Ball (3 Way 3" DN80) - BS Flanges	Service part / kit
525-0304	Gallon Can	Service part / kit
525-0305	12 oz. Pressurized Spray Can	Service part / kit
525-0306	Quart Can	Service part / kit
5410770	Cummins enclosed C2000D5 diesel generator set powered by QSK60G3 engine provides reliable continuous power for Bab Gas Compression Facility.	Service part / kit
898-1254-25	Sleeving – Heater Leads (59”)	Service part / kit
A026N045	Bracket, Mounting	Service part / kit
A026N055	Bracket, Mounting	Service part / kit
A026N058	Leg, Box	Service part / kit
A026N061	Leg, Box	Service part / kit
A026N070	Panel, Cover	Service part / kit
A029F250	Insulation, Duct	Service part / kit
A029F255	Insulation, Duct	Service part / kit
A029S366	Lead, Ground	Service part / kit
A029Y658	Stud	Service part / kit
A040C685	Bracket, Support	Service part / kit
A041U339	Shim, Generator Mounting	Service part / kit
A041U341	Shim, Generator Mounting	Service part / kit
A056A610	RECOMMENDED SPARES LIST (RSL) FOR DQKAD GENERATOR SETS	Service part / kit
A056A611	RECOMMENDED SPARES LIST (RSL) FOR DQKAE GENERATOR SETS	Service part / kit
A056A612	RECOMMENDED SPARES LIST (RSL) FOR DQKAF GENERATOR SETS	Service part / kit
A056F840	Recommended Spares List (RSL) for DQKAN Generator Sets	Service part / kit
M-3089173	Bushing - Camshaft	Service part / kit
M-4007741	Bushing - Camshaft	Service part / kit
M-4089083	Single Cylinder Head	Service part / kit
M-4089200	Juego de Junta Modul. N. ° de Pieza	Service part / kit
M-4089201	Juego Posenfriador Cuadrante N. ° de Pieza	Service part / kit
M-4089202	Juego Sistema Enfriamiento N. ° de Pieza	Service part / kit
M-4089231	Juego de Junta Modul. N. ° de Pieza	Service part / kit
M-4089232	Juego Posenfriador Cuadrante N. ° de Pieza	Service part / kit
M-4089307	Juego Bomba Inferior N. ° de Pieza	Service part / kit
M-4089308	Juego Combustible Inferior N. ° de Pieza	Service part / kit
M-4089508	Juego de Junta Modul. N. ° de Pieza	Service part / kit
M-4089509	Juego Sistema Enfriamiento N. ° de Pieza	Service part / kit
M-4089874	Juego Bloque Inferior N. ° de Pieza	Service part / kit
M-4955369	Juego Posenfriador Cuadrante N. ° de Pieza	Service part / kit
M-4955370	Juego de Junta Modul. N. ° de Pieza	Service part / kit
M-4956000	Culata Cilindro Simple N. ° de Pieza AR	Service part / kit
132-0475	Pump, Water (Remote)	Pump
A054B161	Schematic Diagram	Schematic diagram
323-1445	* Seal, Cable (Used With Station 17)	Seal
323-1708	# Seal, Cable (P8)	Seal
503-2129-05	Line, Vent – Flexible – With One Male Pipe Swivel and One Female Pipe Swivel With O–Ring Face Seal (1/4” ID x 94–1/2”) Right Side	Seal
509-0283-01	Seal	Seal
509-0478	Seal - O Ring	Seal
193-0486	Sender, Low Coolant Level	Sensor
338-3832	Harness, Wiring – Low Coolant Level Sender (4 Wire, 169”) (Includes Parts Marked *)	Sensor
504-0262	Valve, Solenoid	Sensor
AM47478880	Temperature Sender, Exhaust Temperature Replaces 47367178, 87482353, LB52S00001P1	Sensor
AM47520140	Sensor, 8-Pin/NH3/Ammonia Replaces 47368956, 84382712	Sensor
AM47520143	Sensor, Def/AdBlue Quality Replaces 84553250	Sensor
AM504372225	Sensor, MAP Temperature/Pressure Replaces 2852821, 4896794, 504073323	Sensor
M-3331970	Spacer Gasket for QSK45 and QSK60 Engine applications	Spacer gasket
309-0649	Thermostat (Includes Connector Socket) (S11)	Thermostat
309-0711	Thermostat	Thermostat
M-4089203	Juego Turbo e Interenfriador N. ° de Pieza	Turbocharger
M-4089233	Juego Turbo e Interenfriador N. ° de Pieza	Turbocharger

Parts cataloged across all variants of this engine family — verify the exact part fits your specific variant and serial number before ordering.

Common questions

Which generators use the Cummins/Onan QSK60-G19 engine?

The Cummins/Onan QSK60-G19 powers 1 generator set(s), including Cummins/Onan DQKAN.

What is a common problem with the Cummins/Onan QSK60-G19 engine?

A commonly reported issue on generators using the Cummins/Onan QSK60-G19 is: The control will not allow the starter to attempt to engage or to crank. Cause: Not specified in text.