Deutz F3M 2011 F Engine

⚠ Before towing the generator, ensure the towing equipment of the vehicle matches the towing eye

Tools: Jack, Blocks

1. Pull the towing eye out to the outermost position; hand brake lever downward.
2. Loosen the lock nuts.
3. Turn adjusting nuts and brake cable nuts clockwise until no slack remains.
4. Keep the equalizer perpendicular to the main brake cable.
5. Apply the hand brake lever several times and repeat the adjustment.
6. Tighten the nuts with their lock nuts.
7. Remove the jack and the blocks.
8. Road test the generator and brake several times.

⚠ Before jacking up the generator, connect it to a towing vehicle or attach a weight of minimum 50 kg to the towbar

Tools: Wrench, Pin 4 mm

1. Check brake lining thickness through the plugs (5); replace shoes at 1 mm or less.
2. Lift and support the generator; make sure all brakes are off.
3. Lock the swivel cams from outside using a 4 mm pin.
4. Turn the adjusting bolt clockwise with a wrench until the wheel locks up.
5. Center the brake shoes by actuating the parking brake several times.
6. Turn the adjusting bolt anti-clockwise until the wheel runs free (approx. 1 full turn).
7. Check the equalizer is perpendicular with the parking brake actuated.
8. Remove the locking pin and check all lock nuts.

⚠ Height adjustment should be undertaken on levelled ground and in coupled condition

Tools: Support tools, Extension tube

1. Remove spring pin (1).
2. Release locking nut (2) with extension tube (3).
3. Adjust required height of the towbar.
4. Tighten locking nut (2) by hand first.
5. Tighten locking nut (2) to the torque in the table.
6. Fix locking nut (2) with spring pin (1).

⚠ Before handling batteries, read the relevant safety precautions

Tools: Electrolyte (sulphuric acid solution in distilled water)

1. Take out the battery.
2. Battery and electrolyte must be at equal temperature above 10°C.
3. Remove cover and/or plug from each cell.
4. Fill each cell with electrolyte until level reaches 10 to 15 mm above plates.
5. Rock the battery a few times so air bubbles escape; wait 10 minutes and recheck.
6. Refit plugs and/or cover.
7. Place the battery in the generator.

⚠ Observe all relevant environmental and safety precautions

Tools: Petroleum jelly

1. Keep the battery clean and dry.
2. Keep the electrolyte level at 10 to 15 mm above the plates.
3. Top up with distilled water only.
4. Keep terminals and clamps tight, clean and lightly covered with petroleum jelly.

⚠ Never steam clean the alternator

⚠ Never leave spilled liquids in or around the generator

Tools: Fibre brush, Steam cleaner

1. Keep the oil-cooler clean to maintain cooling efficiency.
2. Remove fan cowl upper part to reach fan side surface of oil cooler.
3. Remove centre part of front baffles to reach opposite surface.
4. Steam cleaning with a cleansing agent may be applied.
5. Remove dirt with a fibre brush; never use a wire brush or metal objects.
6. Angle jet at approx. 90° to the coolers to avoid damage.
7. Protect electrical and controlling equipment and air filters against moisture.
8. Close the service doors afterwards.

⚠ Never leave spilled liquids in or around the generator

Tools: Drain pan

1. Place an appropriate drain pan under the drainplug of the fuel tank.
2. Remove the drain plug.
3. Lift the towbar and tilt the generator approx. 15° to remove all fuel, dirt and water.
4. Clean the fuel tank and fix the drain plug handtight.
5. Refill the fuel tank with clean fuel.

⚠ When charging batteries, each cell must be open

Tools: Automatic battery charger

1. Check electrolyte level in each cell before and after charging; top up with distilled water only.
2. Keep each cell open, i.e. plugs and/or cover removed.
3. Prefer the slow charging method.
4. Set charge current to battery capacity in Ah divided by 20.
5. Use a commercial automatic battery charger according to its manufacturer's instructions.

⚠ Never run the generator without air filter element

⚠ The safety cartridge cannot be cleaned

1. Release the snap clips and remove the dust trap; clean the trap.
2. Remove the element from the housing.
3. Inspect new elements for tears or punctures before installation.
4. Discard the element when damaged.
5. Reassemble in reverse order of dismantling.
6. Inspect and tighten all air intake connections.
7. Reset the vacuum indicator.

⚠ Never remove the cooling system filler cap while coolant is hot

⚠ Never mix different coolants

⚠ Topping up with water only is not allowed

1. Drain the entire cooling system completely.
2. Dispose or recycle used coolant per local laws.
3. Flush twice with clean water.
4. Determine amount of PARCOOL EG required and pour into the radiator top tank.
5. Run the engine until normal operating temperature is reached, then stop and cool.
6. Recheck coolant level and add if necessary.

⚠ Never leave spilled liquids in or around the generator

1. Unscrew the filter element from the adapter head.
2. Clean the adapter head sealing surface.
3. Lightly oil the gasket of the new element.
4. Screw the new element onto the header until the gasket is properly seated.
5. Tighten with both hands.
6. Check for fuel leaks once the engine has been restarted.

⚠ The lighting tower should never be left unattended

⚠ Before moving the unit, ALWAYS lower the mast and secure it on the transport frame

⚠ When the genset is mounted on a lighting tower it is NOT permitted to use the lifting eye

1. Position the generator: rear-end upwind, immobilize with handbrake or chocks, level with jockey wheel.
2. Extend the four stabilizers as far as possible and lock with levers HLS.
3. Unlock and lower the stabilizer feet; lock in a foreseen hole.
4. Wind down the foot until it touches the ground and clamps the stabilizer firmly.
5. Loosen the elevation cable by turning the winding mechanism lever clockwise.
6. Unlock the mast by raising lever LTF at the back of the transport frame.
7. Raise the mast from horizontal to vertical; check the locking pin secures the vertical position.
8. Raise the mast to the desired height by turning the winding mechanism lever.