71 ecm / ecu modules cross-referenced across the generator & engine catalog — each with its part number, the engines and sets that use it, and where to buy. Search and filter the full parts catalog by brand or engine.
| Part # | Description | Used by | |
|---|---|---|---|
| 3-173 | SERIES 50/SERIES 60 ENGINE-MOUNTED ECM (STANDARD OPTION) | 4 | buy |
| 23516935 | PLATE ASM COLD ECM END MT DDEC III | 2 | buy |
| 3-181 | SERIES 2000 ENGINE SIDE OF ECM | 2 | buy |
| 1078 | ECU/Pump timing status | 1 | buy |
| 1136 | ECU Temperature | 1 | buy |
| 6SA0580 | Engine Control Module | 1 | buy |
| GM19763 | Module, NG ECU control, 80 kW | 1 | buy |
| GM19765 | Module, LP ECU control, 80 and 100 kW | 1 | buy |
| GM19766 | Module, NG ECU control, 100 kW | 1 | buy |
| GM22170 | Module, LP ECU control, 125 kW | 1 | buy |
| GM25969 | Module, NG ECU control, 125 kW | 1 | buy |
| GM29245 | ECU | 1 | buy |
| GM29607 | ECU | 1 | buy |
| GM29610 | Isolator, ECU | 1 | buy |
| GM66246 | ECU | 1 | buy |
| GM66247 | ECU | 1 | buy |
| GM66249 | ECU | 1 | buy |
| KO3217-9 | Jumper Plug, Blue (for plastic cased ECU) | 1 | buy |
| P.22 | Engine Control Unit or Starting Key | 1 | buy |
| RG10021 | Viewing Stored Service Codes/Diagnostic Trouble Codes (DTCs) in the Engine ECU | 1 | buy |
| g00908008 | Illustration 39: ECM The ECM functions as the governor and the computer for the fuel system. The ECM receives all the signals from the sensors in order to control the timing and the engine speed. | 1 | buy |
| g00908010 | Illustration 41: Schematic for speed/timing sensor When the engine is cranking, the ECM uses the signal from the speed/timing sensor in the fuel injection pump. When the engine is running the ECM uses the signal from the speed/timing sensor on the crankshaft. This speed/timing sensor is the primary source of the engine position. | 1 | buy |
| g00908817 | Illustration 43: Schematic for the temperature sensors The air inlet temperature sensor and the coolant temperature sensor are passive sensors. Each sensor provides a temperature input to the ECM. The ECM controls following operations: • Fuel delivery • Injection timing The operating range for the sensors ............ −40 °C to 150 °C (−40 °F to 302 °F) The sensors are also used for engine monitoring. | 1 | buy |
| i01854884 | Power Sources Introduction (Power Supplies) The 1106 Engine has four supplies to the following components: • ECM • Fuel Injection Pump • Pressure sensors • Air inlet heater | 1 | buy |
| 000627.18 | ECU EEPROM Error | 0 | buy |
| 000629.12 | ECU Boot Block Error | 0 | buy |
| 030-2650 | Dual ECU Switch Box | 0 | buy |
| 04-160-289 | Internal ECU Failure Diagnostic Procedure | 0 | buy |
| 04-160-292 | Pump or ECU Failure Diagnostic Procedure | 0 | buy |
| 24 584 28 | ECU | 0 | buy |
| 2469051 | ECU-återställning | 0 | buy |
| 401-0065 | ATS (ECU request (message or warning light activation) refer to the machine documentation) | 0 | buy |
| 421-4367 | Engine Control Unit (ECU) | 0 | buy |
| 4U36MS2VHB | Electronic Control Unit Circuit Board (ECU) | 0 | buy |
| 54-377-000 | Engine Control Module (ECM) Replacement | 0 | buy |
| 65541-48 | ECM | 0 | buy |
| C071312 | SWITCHBOARD, DUAL ECM | 0 | buy |
| C071480 | 3PDT TOGGLE SWITCH (ECM) | 0 | buy |
| CN-11 | Temperature sensor plug on ECU board | 0 | buy |
| CN-12 | Low Pressure Switch connection terminal on ECU | 0 | buy |
| CN-13 | High Pressure Switch connection terminal on ECU | 0 | buy |
| CN-14 | System temperature sensor plug on ECU board | 0 | buy |
| CN-15 | EEV stepper motor connection terminal on ECU | 0 | buy |
| CN-23 | SMB connection terminal on ECU board | 0 | buy |
| DA2251205 | 0 | buy | |
| DA2251214 | 0 | buy | |
| DA2251265 | 0 | buy | |
| E01-2564-000 | Electronic Control Unit (ECU) | 0 | buy |
| GM28747- | ECM Wiring for 10/13/15EG, 10/13/15ERG, 15/30RES, and 15/30RYG Models | 0 | buy |
| MVP-193 | Mefi-6 ECU | 0 | buy |
| P1FD9-00 | ECU - Runtime reached the maximal time without reset | 0 | buy |
| P1FDE-00 | ECU power supply (current) - Overcurrent warning | 0 | buy |
| P2506-18 | ECU power supply (current) - Critical overcurrent | 0 | buy |
| P3049-19 | ECU digital output half full bridge - Critical overcurrent | 0 | buy |
| P3105-00 | ECU - CPU overload warning | 0 | buy |
| P3106-00 | ECU - CPU critical overload | 0 | buy |
| RG12006 | Engine Control Unit (ECU) | 0 | buy |
| S4008500710 | ECU ABS | 0 | buy |
| S4008501300 | HABS ECU | 0 | buy |
| S4008503070 | ABS/ECU | 0 | buy |
| S4008503100 | ABS/ECU | 0 | buy |
| S4460037030 | ECU 4S/4 | 0 | buy |
| S4461082010 | ECU TCS11 | 0 | buy |
| TP-6362 | ECM Service Manual for the 1.6L Engine | 0 | buy |
| TP-6724 | ECM Service Manual for Emission Certified 1.6L, 3.0L, 4.3, 5.0L, 5.7, 8.1L, & 8.8L Engine | 0 | buy |
| U1029-00 | Engine Control Unit PME CAN - Invalid IO-config file received from Master | 0 | buy |
| U1049-00 | Engine Control Unit CAN - CAN1 message received after end of post drive | 0 | buy |
| U3000-00 | ECU - Internal error | 0 | buy |
| g02722357 | Typical example of the ECM | 0 | buy |
| i01798103 | Replacing the ECM | 0 | buy |
| i03434204 | Test ECM Mode | 0 | buy |