Specifications
| Fuel | gasoline |
|---|---|
| Frequency | 60.0 Hz |
| Emissions | CARB Tier 3 / EPA Phase 3 |
| Controller | Integral box |
| Oil capacity | 1.9 L |
| Alternator | revolving field AC, 2-pole self-excited (2-pole, Class meets ANSI/RVIA EGS-1 and CSA Electrical Bulletin 946 insulation) |
| Voltage options | 120 V |
| Phase | 1 |
| Rated current | 58.3 A |
| Circuit breaker | 30 A |
| Max ambient | 49 °C |
| Dimensions (L×W×H) | 853×563×424 mm |
| Dry weight | 131 kg |
| Sound level | 70.0 dBA @ 3 m |
Engine
| Oil capacity | 1.9 L |
|---|---|
| Coolant capacity | 0.0 L |
| Displacement | 0.653 L |
| Aspiration | naturally aspirated |
| Rated speed | 2880 rpm |
Maintenance & consumables
for the Cummins/Onan OHV EH65V| Item | Spec | Capacity | Part # | Interval | |
|---|---|---|---|---|---|
| Air filter | replaceable dry element air cleaner | — | |||
| Fuel filter | long-life fuel filter | — | |||
| Oil filter | spin-on, full-flow lube oil filter | — | |||
| Battery | Battery charging - 5 A | — | |||
| Belt | 2 in exhaust tubes, straight with flanged end | — | |||
| Coolant | Centrifugal blower, generator set-mounted for high effectiveness, pressurized system, vertical flow | — | |||
| Oil | spin-on, full-flow lube oil filter | 2.0 L | — | ||
| Spark plug | Electronic magneto type with resistor plugs | — |
Service specifications
9| Type | Item | Value | Unit | Condition |
|---|---|---|---|---|
| Other | EC-AGS+ gateway dimensions | 120 x 108 x 38 | mm | |
| Other | Temperature sensor dimensions | 51 x 70 x 17 | mm | |
| Resistance | Gateway harness continuity maximum resistance | 10 | Ohms | repair or replace harness if greater |
| Temperature | EC-AGS+ gateway operating temperature range | -40 to 70 | °C | |
| Temperature | Temperature sensor operating temperature range | -40 to 85 | °C | |
| Voltage | EC-AGS+ nominal operating voltage | 12 | V | nominal |
| Voltage | EC-AGS+ operating voltage range | 8 to 16 | VDC | |
| Voltage | Minimum house battery voltage for AGS use | 9 | V | AGS not allowed below this |
| Voltage | Temperature sensor battery replacement threshold | 2.5 | V | replace when below |
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Recommended fluids
| Fluid | Grade | Standard | Ambient | Capacity | Notes |
|---|---|---|---|---|---|
| Engine oil | Full pressure positive displacement pump | -29°C to 49°C | 2.0 qt | Gasoline models: -20°F to 120°F (-29°C to 49°C); LP models: 0°F to 120°F (-18°C to 49°C) |
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Procedures
6Installation and Setup Test diagnostic
- Verify generator set operation using the Start/Stop switch located on the generator set.
- Verify manual start/stop of the generator set from the app dashboard using the START and PRIME/STOP buttons.
- Check operation of the temperature sensors with Auto mode and Air Conditioning Sense enabled.
- Verify the generator set starts automatically when the settings are met.
- Verify the accelerometer by driving the vehicle at 10 mph and checking that AGS is automatically disabled.
- Verify delayed shutdown: enable AGS, allow the generator set to start, disable AGS, confirm shutdown in 10 minutes.
Connect Components (EC-AGS+ Gateway) installation
⚠ Accidental starting of the generator set can cause severe personal injury or death. Disconnect the starting (battery) cables before performing service.
⚠ Always disconnect a battery charger from its AC source before disconnecting the battery cables.
⚠ Seal all holes to prevent the entrance of exhaust gases into the vehicle interior.
- Plug the 12-pin connector from the harness to the EC-AGS+ gateway.
- Route the other end of the harness from the gateway to the Y-harness.
- For gas generator sets, plug the 8-pin EC-AGS+ harness connector into either lead of the Y-harness.
- For diesel generator sets, plug the 10-pin EC-AGS+ harness connector into the longer lead of the Y-harness.
- Connect the main lead of the Y-harness to the generator set.
- Connect the remaining Y-harness connector to the remote start/stop switch harness.
- Route the red wire lead to the positive terminal of the generator set starting battery and extend as necessary using butt connectors.
- Provide circuit protection by installing a 5 Amp fuse in the red wire lead.
- Locate the common ground location on the vehicle and route the black wire lead to the common ground.
- Route the grey wire lead to the engine battery positive terminal (optional connection).
- Insert battery ring terminal to the wires and connect the wires.
- Use cable ties at not less than 0.5 m (20 in) intervals to keep the wire bundle neat.
Connect Temperature Sensor(s) installation
Tools: Small flathead screwdriver
- Remove the lid from the sensor using a small flathead screwdriver.
- Remove the plastic battery tab from the sensor to enable the battery to provide power to the sensor.
- Place the lid back on the sensor.
Mount Components installation
⚠ High ambient temperature can cause damage to the EC-AGS+ gateway.
- Do not install the EC-AGS+ gateway directly inside the generator set compartment.
- Mount the EC-AGS+ gateway in a suitable, easily accessible location.
- Drill holes for the fastening screws and mount the EC-AGS+ gateway using mounting screws.
- Mount the temperature sensor(s) near an A/C thermostat (one per zone, 3 maximum).
- Drill 2 holes for screws and mount the sensor.
Temperature Sensor Battery Replacement maintenance
⚠ Pushing on the cover too hard can damage or break it.
Tools: Small flathead screwdriver
- Make sure the generator set is not set to start in Auto mode.
- Remove the top cover of the temperature sensor using a small flathead screwdriver.
- Slide the battery out of the battery holder and remove the battery.
- Slide the new battery into the battery holder and replace the cover.
Configure System Using App (Getting Started) operation
⚠ For first time set up or after factory reset, the vehicle must be kept stationary for at least 30 seconds to allow the gateway accelerometer to be configured properly.
- Download the EC-AGS+ app from the AppStore for iOS or Play Store for Android.
- Reconnect the generator set negative battery cable to power on the EC-AGS+ gateway.
- Verify that the EC-AGS+ gateway is powered by observing the LED blinking every 5 seconds.
- Turn on Bluetooth on the device containing the app.
- Select the EC-AGS+ App and select Start.
- Connect the gateway to the app via Discover EC-AGS+, Scan QR code, or gateway password.
- Read the End User License Agreement to the end and select Agree.
- Create a new password and select Assign Password.
- Select the generator set model and type; enter the Start Hours from the hour meter if available.
- Select Proceed to Dashboard.
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Common questions
What engine does the Cummins/Onan QG 7000 use?
The Cummins/Onan QG 7000 is powered by the Cummins/Onan OHV EH65V engine.
Is the Cummins/Onan QG 7000 diesel or gas?
The Cummins/Onan QG 7000 runs on gasoline.
What's the oil capacity on a Cummins/Onan QG 7000?
The Cummins/Onan OHV EH65V engine in the Cummins/Onan QG 7000 has an oil capacity of 1.9 liters.
What is the sound level of the Cummins/Onan QG 7000?
The Cummins/Onan QG 7000 is rated at 70.0 dBA at 3 m, per the manufacturer specification sheet.
How much does the Cummins/Onan QG 7000 weigh?
The Cummins/Onan QG 7000 has a dry weight of 131 kg (289 lb).
What voltage does the Cummins/Onan QG 7000 produce?
The Cummins/Onan QG 7000 is offered in 120 V, 1-phase.
What alternator comes on the Cummins/Onan QG 7000?
The Cummins/Onan QG 7000 uses a revolving field AC, 2-pole self-excited alternator. It has 2 poles. Insulation class meets ANSI/RVIA EGS-1 and CSA Electrical Bulletin 946.
Parts
13| Part # | Description | Qty | System | |
|---|---|---|---|---|
| 148-1161 | LPG vapor fuel conversion kit | 1 | Service part / kit | eBay |
| 155-2424 | Exhaust tube, straight with flanged end (7 in) | 1 | Service part / kit | eBay $94.33 |
| 155-2610 | Exhaust tube, straight with flanged end (3 in) | 1 | Service part / kit | eBay |
| 155-2610-01 | Exhaust tube, straight with flanged end (12.5 in) | 1 | Service part / kit | eBay |
| 155-3481-01 | Tailpipe kit (22 in) | 1 | Service part / kit | eBay $100.36 |
| 155-3481-02 | Tailpipe kit (26 in) | 1 | Service part / kit | eBay $77.99 |
| 300-5331 | Remote start/stop rocker switch | 1 | Service part / kit | eBay $148.60 |
| 300-5332 | Remote control with start/stop switch and running time meter | 1 | Service part / kit | eBay $145.00 |
| 300-5333 | Remote control w/start/stop switch and DC voltmeter | 1 | Service part / kit | eBay $240.02 |
| 338-3489-01 | Remote control plug and wire harness (10 ft) | 1 | Service part / kit | eBay $65.25 |
| 338-3489-02 | Remote control plug and wire harness (30 ft) | 1 | Service part / kit | eBay $65.00 |
| 405-6699 | Underfloor mounting kit | 1 | Service part / kit | eBay |
| 539-2057 | Installation template | 1 | Service part / kit | eBay |
Service, wear & replacement parts referenced for this model and its engine — confirm the exact part for your serial number. See the full parts catalog to search and cross-reference.
Fuel consumption
| Rating | Load | L/h | gal/h |
|---|---|---|---|
| 50% | 2.27 | 0.6 | |
| 100% | 3.41 | 0.9 | |
| Full load | 100% | 4.6 | 1.2 |
| Half load | 50% | 2.8 | 0.7 |
| No load | 1.6 | 0.4 |
Available documents
This page was generated from the 6 manufacturer documents above by automated extraction; every figure shown is copied from one of them. How the data is compiled.