Specifications
| Fuel | gasoline/lp |
|---|---|
| Frequency | 50.0 Hz |
| Standby power | 150 kW |
| Prime power | 4 kW |
| Oil capacity | 1.0 L |
| Voltage options | 240 V, 220 V, 120 V |
| Phase | 10 |
| Rated current | [7.1, 9.1, 18.3, 23.3] A |
| Battery quantity | 1 |
| Dry weight | 50 kg |
Maintenance & consumables
for the Cummins/Onan KY/KYD| Item | Spec | Capacity | Part # | Interval | |
|---|---|---|---|---|---|
| Air filter | — | 1000 hr | find | ||
| Fuel filter | — | 500 hr | find | ||
| Oil filter | — | 300 hr | find | ||
| Belt | — | 4000 hr | find | ||
| Coolant | — | 2500 hr | |||
| Coolant filter | — | find | |||
| Oil | 1.0 qt | — |
Common questions
What is the power rating of the Cummins/Onan K?
The Cummins/Onan K is rated 150 kW standby.
What engine does the Cummins/Onan K use?
The Cummins/Onan K is powered by the Cummins/Onan KY/KYD engine.
What fuel does the Cummins/Onan K use?
The Cummins/Onan K runs on gasoline/lp.
Troubleshooting
39Symptoms & remedies
| Symptom | Cause | Remedy |
|---|---|---|
| Engine Does Not Crank | 1. Open control fuse F1. 2a. Check condition of battery and recharge or replace. a. Battery not charged. 2b. Clean and tighten all connections at battery, K1 start solenoid, and starter motor. b. Battery connections loose or dirty. c. Battery cable size too small. 3. Start solenoid (K1) not energized 3a. Check wiring continuity to the start solenoid (K1) coil from control assembly (A1) and from ground to start solenoid (K1). a. Open circuit to start solenoid coil. b. Defective start solenoid coil. 3b. Test start solenoid (K1). 3c. Test Start/Stop switch (S1). 3d. Measure voltage between start solenoid terminal I and ground with switch (S1) held in the Start position. If voltage is not present and continuity and battery check OK, control assembly (A1) is defective. | |
| Engine Cranks But Does Not Start | 4a. Check continuity between starter lead on start solenoid (S1) and ground. a. Open circuit to starter (B1). b. Open circuit between battery (B+) and the start solenoid contact (BAT). c. Defective start solenoid (K1). 4b. Measure voltage between starter terminal and ground with switch (S1) held in the Start position. If voltage is not present and continuity checks OK, start solenoid (K1) is defective. 4c. If voltage is present in step 4b, starter (B1) is defective. | |
| Engine Cranks from Set but Not from Remote Control Panel | 5a. Check wiring continuity between control assembly (A1) and remote Start/Stop switch. a. Open circuit between control assy. (A1) and remote Start/Stop switch. b. Remote Start/Stop switch faulty. | |
| Engine Starts But Stops | 2. Defective low oil level switch. | 2. Disconnect low oil level switch and check set operation. Replace if defective. |
| Engine Starts, Then Stops | 3. No field flash voltage due to: | 3a. Check wiring continuity to the brush block F1-F2, voltage regulator VR1, control assembly A1 and generator B1-B2 and 01-02 windings. Check connections of P5 and P6 connectors on the generator housing. 3b. Check brushes for wear and for contact with the slip rings. 3c. Check slip rings |
| Remote Run Lamp Does Not Illuminate | 5. If remote switch functions properly for starting and stopping genset but meters and run lamp do not operate, and step 1 checks OK, control assy. (A1) defective. | If voltage is not present, replace control assembly (A1). If voltage is present, check continuity of remote control wiring. |
| Too Much DC Load | 6. Turn off the genset, disconnect the remote control, and check for shorts or too many remote accessories. | |
| Engine Misfires | - Faulty ignition due to: a. worn or fouled spark plug b. faulty magneto assembly c. faulty ignition coil d. faulty plug wire e. incorrect ignition timing - Lean fuel mixture due to: a. incorrectly adjusted fuel mixture screws *b. incorrect float level c. dirt in carburetor d. vacuum leak - Contaminated fuel - Carburetor icing - Incorrect timing due to: a. defective magneto b. incorrect flywheel or generator mounting *Gasoline sets only | - Replace spark plug - Replace magneto assembly - Test coil and replace if necessary - Check spark plug wire and replace - Rotor or fan hub improperly installed - Coil assembly if necessary - Adjust carburetor main and idle adjustment screws - Adjust carburetor float level - Disassemble carburetor and clean all passages - Locate leak and correct as required - Drain fuel tank and refill with fresh fuel - In cold weather, place air preheater in winter position - Replace magneto assembly - Check for proper installation, see Generator Service section - Reset spark plug gap - Replace magneto assembly - Adjust carburetor main and idle adjustment screws - Adjust carburetor float level - Disassemble carburetor and clean all internal passages - Locate leak and correct as required - See Engine Block Assembly section |
| Engine Backfires | - Faulty ignition due to: a. worn or fouled spark plug b. faulty magneto assembly c. faulty ignition coil d. faulty plug wire e. incorrect ignition timing - Lean fuel mixture due to: a. incorrectly adjusted fuel mixture screws *b. incorrect float level c. dirt in carburetor d. vacuum leak - Contaminated fuel - Carburetor icing - Incorrect timing due to: a. defective magneto b. incorrect flywheel or generator mounting *Gasoline sets only | - Replace spark plug - Replace magneto assembly - Test coil and replace if necessary - Check spark plug wire and replace - Rotor or fan hub improperly installed - Coil assembly if necessary - Adjust carburetor main and idle adjustment screws - Adjust carburetor float level - Disassemble carburetor and clean all passages - Locate leak and correct as required - Drain fuel tank and refill with fresh fuel - In cold weather, place air preheater in winter position - Replace magneto assembly - Check for proper installation, see Generator Service section - Reset spark plug gap - Replace magneto assembly - Adjust carburetor main and idle adjustment screws - Adjust carburetor float level - Disassemble carburetor and clean all internal passages - Locate leak and correct as required - See Engine Block Assembly section |
| Engine Lacks Power | - Faulty ignition due to: a. incorrect spark plug gap b. incorrect ignition timing - Dirty air cleaner - Restricted fuel flow due to: *a. Plugged fuel filter or *b. faulty fuel pump dirty or defective. - Incorrect fuel mixture due to: a. incorrectly adjusted fuel mixture screws *b. incorrect float level or c. dirt in carburetor d. vacuum leak *c. LPG - Regulator or fuel solenoid - Exhaust system blocked or restricted - Incorrect valve lifter - No load speed set too low - Excessive engine wear or damage to engine - Carburetor air preheater set incorrectly *Gasoline sets only | - Reset spark plug gap - Replace magneto assembly - Replace air cleaner - Replace fuel filter - Test fuel pump and replace if faulty - Refer to LPG Fuel section. - Adjust carburetor main and idle adjustment screws - Adjust carburetor float level - Disassemble carburetor and clean all internal passages - Repair vacuum leak. - Locate and remove cause of blockage, remove and clean spark arresting screen - Adjust valve lifters/inspect valves (see Engine Block Assembly section) - Adjust governor setting - See Engine Block Assembly section - In hot weather, place air preheater in summer position - Clear away any debris that may restrict airflow to set and do not use compartment for storage area - Clean away all dirt and oil from engine cooling fins - Replace magneto assembly - Inspect cooling fan, see Generator Service section - Adjust carburetor main and idle adjustment screws - Adjust carburetor float level - Disassemble carburetor and clean all internal passages |
| Black Exhaust Smoke | - Rich fuel mixture due to: a. dirty air cleaner *b. choke sticking c. incorrectly adjusted fuel mixture screws d. dirt in carburetor *Gasoline sets only - Lean fuel mixture due to: *a. incorrect float level b. incorrectly adjusted fuel mixture screws c. dirt in the carburetor | - Adjust carburetor main and idle adjustment screws - Adjust carburetor float level - Disassemble carburetor and clean all internal passages |
| White or Blue Exhaust Smoke | - Rich fuel mixture due to: a. dirty air cleaner *b. choke sticking c. incorrectly adjusted fuel mixture screws d. dirt in carburetor *Gasoline sets only - Lean fuel mixture due to: *a. incorrect float level b. incorrectly adjusted fuel mixture screws c. dirt in the carburetor | - Adjust carburetor main and idle adjustment screws - Adjust carburetor float level - Disassemble carburetor and clean all internal passages |
| Engine Hunts or Surges | - Sticking or binding governor linkage - Incorrect governor adjustment - Faulty governor spring - Incorrect fuel mixture due to: a. incorrectly adjusted | - Adjust valve lifters/inspect valves (see Engine Block Assembly section) - Adjust governor setting |
| Run Lamp, work but time meter does not | Battery condition meter and time meter are defective. | Replace time meter. If time meter works but battery condition meter does not operate: a. Defective battery condition meter. b. Defective zener diode inside remote control. |
| Run Lamp, does not illuminate | Lamp (internal to switch) is burned out. Replace remote Start/Stop switch (S2). | |
| Meters and run lamp do not operate, control assembly (A1) defective | Check remote running output voltage from control assembly J1-2 to ground and from P5-6 to ground. If voltage is not present, replace control assembly (A1). If voltage is present, check continuity of remote control wiring. | |
| Too much DC load connected to the remote output | Turn off the genset, disconnect the remote control, and check for shorts or too many remote accessories. | |
| Fails To Crank | Low battery, Bad battery connection, Blown fuse | Check battery fluid level, Clean & tighten all battery & cable connections, Replace fuse on control panel |
| Cranks But Won’t Start | Fuel below generator pickup level in tank, Fuel supply shutoff valve closed, Carbon deposits on spark plug(s), Low oil level | Add fuel, Fully open fuel supply valve, Remove spark plug(s) and replace, Add oil |
| Exhausting Black Smoke | Dirty air filter | Replace air filter |
| Unit Runs Then Stops, Or Stops When Driving Around A Corner | Low fuel level, Low oil level, Excess oil | Add fuel, Add oil, Reduce engine oil level |
| Unit Starts And Runs, Then Stops When The Start Switch Is Released | Low fluid levels, Possible overheating, Other functional problem | Check & bring all fluids up to the appropriate levels, Check for blocked air flow or other possible causes of overheating, Contact an Cummins Onan Authorized RV Service & Parts Dealer |
| Unit Runs Then Surges | Loose or worn spark plug leads, Defective ignition coil, wiring, or control components, Faulty spark plug, Governor out of adjustment, Combustion air pre-heat malfunction, Carburetor icing, Carburetor varnishing | Check spark plug leads at spark plug & ignition coil, Contact an Cummins Onan Authorized RV Service & Parts Dealer, Remove spark plug & clean or replace, Contact an Cummins Onan Authorized RV Service & Parts Dealer, Contact an Cummins Onan Authorized RV Service & Parts Dealer, Contact an Cummins Onan Authorized RV Service & Parts Dealer |
| Circuit Breaker Trips | Overloaded circuit | Turn-off some of the electrical load, and reset the circuit breaker |
| The genset stops | Does the genset operate correctly from the genset controls? If it does not, the problem is in the genset, not the EC-20 controller. See the genset Operator, Installation, and Service Manuals. | |
| The indicator light in the Start/Stop switch turns off | Confirm that the correct connection diagram (Figures 5 - 7) was used, then check EC 30 wiring connections. Confirm that the correct voltages are present on each terminal. Check all terminal connections on both ends of the wiring harness. Are harness connectors properly joined? | |
| Engine Overfueling | Check: Spark plugs, Fuel pressure at carburetor, Vacuum pull-off, Choke heater. Perform checks in step 01. Check: Governor adjustments, Carburetor adjustments. Perform checks in step 02. | |
| Engine Unstable (Hunts) | Check: Fuel supply, Fuel Lines for leakage, Loose wire connection. Perform checks in step 01. Check: Governor linkage for binding, Governor adjustments, Carburetor adjustments. | |
| Engine Will Not Crank | Check: Low battery voltage, Terminal connections, Battery cable size. Perform checks in step 01. Check: Remote control, Blown fuse, Start solenoid, Start disconnect relay. | |
| High/Low AC Output | Check: Broken or loose wires, Voltage regulator, Engine speed. Perform checks in step 01. Check: Main rotor, Main stator. Adjust engine speed. | |
| Starts But Stops When Switch is Released | Check: Oil level, Choke element, Engine speed. Perform checks in step 01. Check: All electrical connections, Start disconnect relay, AC voltage regulator, Control board (KV Begin Spec C, KVD All Specs). Perform checks in step 02. Check: Main rotor, Main stator. | |
| Time Meter, inoperative | Defective battery condition meter.; Defective zener diode inside remote control | Connect a voltmeter between the positive terminal on battery charge meter and ground. Use the following to determine fault: If reading equals battery voltage minus 10 volts, battery condition meter is defective.; If reading does not equal battery voltage minus 10 volts, zener diode is defective. |
| Run Lamp does not illuminate | Lamp (internal to switch) is burned out. Replace remote Start/Stop switch (S2). | |
| Remote switch functions properly for starting and stopping genset but meters and run lamp do not operate, and step 1 checks OK | Control assy. (A1) defective. If voltage is not present, replace control assembly (A1). If voltage is present, check continuity of remote control wiring. | |
| Too much DC load (over 2-amps) connected to the remote output | Turn off the genset, disconnect the remote control, and check for shorts or too many remote accessories. | |
| Low Battery Voltage | Weak or discharged battery due to: a. Low electrolyte level in battery.; b. Long periods of non-use.; c. Improperly wired battery.; d. Load connected to battery while set is turned off.; e. Too much DC load on genset starting battery. | Replenish electrolyte and recharge battery.; Connect a separate battery charger to bring battery up to full charge.; Reconnect and check battery connection.; Disconnect load and recharge battery.; Remove other DC loads from genset starting battery. |
| Genset charging circuit not functioning | A. Open in circuit between generator B1-B2 winding and Battery B+ connection, including all connections to the diode bridge (CR1) and battery charge resistor (R1).; b. Open charging resistor (R 1).; c. Diode bridge (CR1) defective.; d. Generator B1-B2 defective. | Remove wires from the charge resistor (R1) and measure its resistance. A normal reading is 4 to 6 ohms.; Refer to diode bridge (CR1) test section.; Refer to generator test section. |
| Genset does not stop when Start/Stop switch is pushed to Stop | A. Check wiring continuity between control assembly (A1) and remote Start/Stop switch.; b. Remote Start/Stop switch faulty. | Check remote Start/Stop switch. |
| Genset can be stopped from remote control but not from set | Check Start/Stop switch (S1). |
Fault codes and symptom→remedy steps extracted from this model’s service/owner documentation; verify against the official manual before servicing.
Parts
179| Part # | Description | Qty | System | |
|---|---|---|---|---|
| 110-3882 | Rings, Valve Guide | 2 | Seal | PartsGeek |
| 110-3893 | Gasket, Cylinder Head | 1 | Gasket | PartsGeek |
| 123-1917 | Tube, Breather | 1 | Hose | PartsGeek |
| 141-0641 | Gasket Kit, Carburetor Parts Included in 145-0410 Throttle | 1 | Gasket | PartsGeek |
| 149-2311-01 | Pump, Fuel Electric | 1 | Pump | PartsGeek |
| 149-2457 | Filter, Fuel | 1 | Fuel filter | PartsGeek FridayParts $12.00 |
| 153-0639 | Gasket, Intake Manifold | 1 | Gasket | PartsGeek |
| 153-0640 | Element, Choke Thermostat | 1 | Thermostat | PartsGeek |
| 167-0275 | Plug, Spark (60Hz) | 1 | Spark plug | PartsGeek |
| 167-0305 | Plug, Spark (50Hz) | 1 | Spark plug | PartsGeek |
| 168-0213 | Gasket Kit KY | 1 | Gasket | PartsGeek |
| 191-0732 | Alternator Regulator | 1 | Alternator | PartsGeek |
| 294306 | Enclosure, transfer panel | 1 | Enclosure | PartsGeek |
| 295004 | Latch, locking | 1 | Latch | PartsGeek |
| 295034 | Socket, relay | 5 | Sensor | PartsGeek |
| 295044 | Transformer | 2 | Sensor | PartsGeek |
| 295045 | Transformer | 4 | Sensor | PartsGeek |
| 295048 | Transformer | 1 | Sensor | PartsGeek |
| 295064 | Transformer assy, 110-120V | 1 | Sensor | PartsGeek |
| 295066 | Transformer assy, 380-416V | 1 | Sensor | PartsGeek |
| 295068 | Switch, toggle | 1 | Sensor | PartsGeek |
| 295253 | Relay (DPDT) | 3 | Sensor | PartsGeek |
| 295254 | Relay (DPDT) | 2 | Sensor | PartsGeek |
| 295280 | Transformer | 2 | Sensor | PartsGeek |
| 295281 | Transformer | 2 | Sensor | PartsGeek |
| 295282 | Transformer | 2 | Sensor | PartsGeek |
| 295283 | Transformer | 2 | Sensor | PartsGeek |
| 295284 | Transformer | 4 | Sensor | PartsGeek |
| 295285 | Transformer | 4 | Sensor | PartsGeek |
| 295286 | Transformer | 4 | Sensor | PartsGeek |
| 295287 | Transformer | 4 | Sensor | PartsGeek |
| 295289 | Transformer | 4 | Sensor | PartsGeek |
| 295291 | Transformer | 4 | Sensor | PartsGeek |
| 295292 | Transformer | 4 | Sensor | PartsGeek |
| 295293 | Transformer | 4 | Sensor | PartsGeek |
| 295951 | Dead Buss Relay, 440-480V | 1 | Sensor | PartsGeek |
| 295987 | Relay assy | 1 | Sensor | PartsGeek |
| 297372 | Board assy, circuit | 1 | Sensor | PartsGeek |
| 297373 | Board assy, circuit | 1 | Sensor | PartsGeek |
| 297498 | Single Phase Sensing Board assy | 1 | Sensor | PartsGeek |
| 297499 | Single Phase Sensing Board assy | 1 | Sensor | PartsGeek |
| 297822 | Dead Buss Relay, 110-120V | 1 | Sensor | PartsGeek |
| 297823 | Dead Buss Relay, 190-208V | 1 | Sensor | PartsGeek |
| 297824 | Dead Buss Relay, 220-240V | 1 | Sensor | PartsGeek |
| 297825 | Dead Buss Relay, 380-416V | 1 | Sensor | PartsGeek |
| 297826 | Dead Buss Relay, 550-600V | 1 | Sensor | PartsGeek |
| 298776 | Base, tie wrap | 2 | Base | PartsGeek |
| 298777 | Enclosure complete | 1 | Envelope | PartsGeek |
| 503-1851 | Clamp, Hose | 2 | Hose | PartsGeek |
| 503-2735 | Hose, Fuel | 1 | Hose | PartsGeek |
| 509-0289 | Seal, Valve Stem | 1 | Seal | PartsGeek |
| 510-0182 | Seal, Oil | 1 | Seal | PartsGeek |
| 981-0503 | Spark Plug | 2 | Spark plug | PartsGeek |
| 981-0607 | Fuel Filter | 1 | Fuel filter | PartsGeek |
| A-295045 | Transformer assy, 220-240V | 1 | Sensor | PartsGeek |
| A-295046 | Transformer assy, 440-480V | 1 | Sensor | PartsGeek |
| A-295047 | Transformer assy, 550-600V | 1 | Sensor | PartsGeek |
| A-295048 | Transformer assy, 110-120V | 1 | Sensor | PartsGeek |
| A-295050 | Transformer assy, 380-416V | 1 | Sensor | PartsGeek |
| A065U664 | Temperature Sensor (with Mounting Screws) | 1 | Temperature sensor | PartsGeek |
| FS-1483.2 | FIGURE 6-11. MIXTURE NEEDLE INSPECTION | Figure | PartsGeek | |
| FS-1606-1 | BI-METAL SPIRAL STRIP | Bi-metal spiral strip | PartsGeek | |
| FS-1757-3 | COVER | Cover | PartsGeek | |
| FS-176D | CAP | Cap | PartsGeek | |
| FS-17E-2 | FIGURE 6-13. FLOAT LEVEL | Figure | PartsGeek | |
| L-74 | WASHER -b@ | Washer | PartsGeek | |
| M-1677 | SPEED ADJUSTMENT SCREW | Screw | PartsGeek | |
| M-1678 | SPEED ADJUSTMENT SCREW | Screw | PartsGeek | |
| SN5304U1G2RA | Engine | 1 | Engine | PartsGeek |
| X-25-7 | Washer, plain | 4 | Washer | PartsGeek |
| X-6003-36 | Conduit, plastic | 1 | Hose | PartsGeek |
| 044-00074 | 25' Harness - QG 2800, 2500 Generators | 25 | Service part / kit | PartsGeek |
| 044-00075 | 25' Harness - QG 7000, 6500, 5500, 4000, 3600 Generators | 25 | Service part / kit | PartsGeek |
| 044-00076 | 25' Harness - QD Generators | 25 | Service part / kit | PartsGeek |
| 044-00077 | 18" Pigtail | 18 | Service part / kit | PartsGeek |
| 100-4152 | Engine (Spec A-L) | 1 | Service part / kit | PartsGeek |
| 104-1721-01 | Piston Standard | 1 | Service part / kit | PartsGeek |
| 104-1721-02 | Piston 0.25 Oversize | 1 | Service part / kit | PartsGeek |
| 104-1780 | Crankshaft | 1 | Service part / kit | PartsGeek |
| 104-1899 | Gear, Balancer | 1 | Service part / kit | PartsGeek |
| 104-1901 | Gear, Crankshaft | 1 | Service part / kit | PartsGeek |
| 110-3698 | Washer, Valve Spring | 2 | Service part / kit | PartsGeek FridayParts $65.78 |
| 110-3700 | Retainer, Valve Spring | 2 | Service part / kit | PartsGeek |
| 110-3701 | Spring, Valve | 2 | Service part / kit | PartsGeek |
| 110-3750 | Bolt, Cylinder Head | 2 | Service part / kit | PartsGeek |
| 110-3887 | Valve, Intake | 1 | Service part / kit | PartsGeek |
| 110-3888 | Valve, Exhaust | 1 | Service part / kit | PartsGeek |
| 110-3890 | Head, Cylinder | 1 | Service part / kit | PartsGeek |
| 110-3914 | Lock, Valve Spring | 2 | Service part / kit | PartsGeek |
| 115-0465 | Arm, Rocker | 2 | Service part / kit | PartsGeek |
| 141-0640 | Repair Kit, Carburetor | 1 | Service part / kit | PartsGeek |
| 146-0646 | Kit, Carburetor Gasoline | 1 | Service part / kit | PartsGeek |
| 146-0765 | Carburetor Emissions | 1 | Service part / kit | PartsGeek |
| 148-0625 | Converter, Gas | 1 | Service part / kit | PartsGeek |
| 150-1456 | Bracket and Point Assembly | 1 | Service part / kit | PartsGeek |
| 151511 | Ring, lock (15ROY,17.5ROY) | 1 | Service part / kit | PartsGeek |
| 201-2673 | Rotor Assembly, Wound (Includes | 1 | Service part / kit | PartsGeek |
| 224233 | Decal, 1-800 number | 1 | Service part / kit | PartsGeek |
| 257442 | Clip, speed | 2 | Service part / kit | PartsGeek |
| 273746 | Decal, UL | 1 | Service part / kit | PartsGeek |
| 294291 | Envelope, instruction | 1 | Service part / kit | PartsGeek |
| 294310 | Decal | 1 | Service part / kit | PartsGeek |
| 294318 | Door, enclosure | 1 | Service part / kit | PartsGeek |
| 294322 | Latch, locking | 1 | Service part / kit | PartsGeek |
| 294414 | Decal, notice | 1 | Service part / kit | PartsGeek |
| 294602 | Decal, stripes | 1 | Service part / kit | PartsGeek |
| 295002 | Door, enclosure | 1 | Service part / kit | PartsGeek |
| 295003 | Retainer | 1 | Service part / kit | PartsGeek |
| 295009 | Clip, wire | 2 | Service part / kit | PartsGeek |
| 295010 | Retainer | 1 | Service part / kit | PartsGeek |
| 295012 | Key | 1 | Service part / kit | PartsGeek |
| 295013 | Nameplate | 1 | Service part / kit | PartsGeek |
| 295015 | Base, tie wrap | 1 | Service part / kit | PartsGeek |
| 295016 | Enclosure complete | 1 | Service part / kit | PartsGeek |
| 295020 | Bracket, transformer | 1 | Service part / kit | PartsGeek |
| 295060 | Decal, part no | 1 | Service part / kit | PartsGeek |
| 295061 | Decal, part no | 1 | Service part / kit | PartsGeek |
| 295062 | Decal, part no | 1 | Service part / kit | PartsGeek |
| 295063 | Decal, part no | 1 | Service part / kit | PartsGeek |
| 295086 | Nameplate | 1 | Service part / kit | PartsGeek |
| 295098 | Screw, flat head machine | 8 | Service part / kit | PartsGeek |
| 295189 | Clamp, relay hold-down | 5 | Service part / kit | PartsGeek |
| 295232 | Decal, Transfer Switch | 1 | Service part / kit | PartsGeek |
| 295306 | Decal, nine-terminal block | 1 | Service part / kit | PartsGeek |
| 295307 | Decal, six-terminal block | 1 | Service part / kit | PartsGeek |
| 295313 | Block, nine-terminal | 1 | Service part / kit | PartsGeek |
| 295314 | Block, six-terminal | 1 | Service part / kit | PartsGeek |
| 295331 | Nameplate | 1 | Service part / kit | PartsGeek |
| 295332 | Nameplate | 1 | Service part / kit | PartsGeek |
| 295392 | Nameplate, serial no | 4 | Service part / kit | PartsGeek |
| 295925 | Cover, terminal strip | 1 | Service part / kit | PartsGeek |
| 295988 | Block, 16-terminal | 1 | Service part / kit | PartsGeek |
| 295989 | Block, eight-terminal | 1 | Service part / kit | PartsGeek |
| 295990 | Bracket, mounting | 1 | Service part / kit | PartsGeek |
| 295991 | Insulator, plate | 1 | Service part / kit | PartsGeek |
| 295992 | Nameplate (NC, NA) | 1 | Service part / kit | PartsGeek |
| 295993 | Nameplate (B5) | 1 | Service part / kit | PartsGeek |
| 296235 | Hinge, split | 1 | Service part / kit | PartsGeek |
| 297071 | Capacitor | 1 | Service part / kit | PartsGeek |
| 297256 | Pedestal Mounting Feet, 30-150A NEMA 3R | 1 | Service part / kit | PartsGeek |
| 297259 | Pedestal Mounting Feet, 225-400A NEMA 3R | 1 | Service part / kit | PartsGeek |
| 297260 | Pedestal Mounting Feet, 225-400A NEMA 1 | 1 | Service part / kit | PartsGeek |
| 297262 | Pedestal Mounting Feet, 600-800A NEMA 3R | 1 | Service part / kit | PartsGeek |
| 297263 | Pedestal Mounting Feet, 600-800A NEMA 1 | 1 | Service part / kit | PartsGeek |
| 297265 | Handle, External Manual Operating, 225-260 Amp | 1 | Service part / kit | PartsGeek |
| 297359 | Bracket, mounting | 2 | Service part / kit | PartsGeek |
| 297600 | Hinge, split | 4 | Service part / kit | PartsGeek |
| 297938 | Nameplate | 1 | Service part / kit | PartsGeek |
| 308-0284 | Switch, Selector | 1 | Service part / kit | PartsGeek |
| 405-1779 | Dry Manifold | 1 | Service part / kit | PartsGeek |
| 405-1813 | Wet Manifold | 1 | Service part / kit | PartsGeek |
| 510-0101 | Bolt, Place - Hex Head, Grade 8 (3/8-16 x 1-1/2”) | 1 | Service part / kit | PartsGeek |
| 510-0160 | Bearing, Block End | 1 | Service part / kit | PartsGeek |
| 56-A360-4901 | adapter | Service part / kit | PartsGeek | |
| 800-0028 | Screw | 1 | Service part / kit | PartsGeek |
| 928-0502B | Service part / kit | PartsGeek | ||
| 928-0506 | Service part / kit | PartsGeek | ||
| 932-0404 | Onan Generator Training Manual | 1 | Service part / kit | PartsGeek |
| 932-0408 | Electrical/Mechanical Fundamentals | 1 | Service part / kit | PartsGeek |
| 960-0135 | Service part / kit | PartsGeek | ||
| 960-0136 | Battery, 24V, 55Ah, AGM | 8 | Service part / kit | PartsGeek |
| 960-0242 | Service part / kit | PartsGeek | ||
| 960-0504A | Service part / kit | PartsGeek | ||
| 960-0505 | Service part / kit | PartsGeek | ||
| 960-12 | Service part / kit | PartsGeek | ||
| 965-0154 | Service part / kit | PartsGeek | ||
| 981-0246 | Service part / kit | PartsGeek | ||
| 981-1054 | Supplement | Service part / kit | PartsGeek | |
| A-295026 | Enclosure complete | 1 | Service part / kit | PartsGeek |
| A-295027 | Enclosure complete | 1 | Service part / kit | PartsGeek |
| A-295044 | RED/BLUE JUMPER | 1 | Service part / kit | PartsGeek |
| B-295028 | Enclosure complete | 1 | Service part / kit | PartsGeek |
| S.F.80 | TRAFFICATOR | Service part / kit | PartsGeek | |
| X-117-4 | Screw | 2 | Service part / kit | PartsGeek |
| X-465-10 | Screw, H.C. | 2 | Service part / kit | PartsGeek |
| X-468-1 | Tie, cable | 1 | Service part / kit | PartsGeek |
| X-51-15 | Screw, R.H.M. 8-32x1/2 | 1 | Service part / kit | PartsGeek |
| X-6220-1 | Enclosure, transfer door | 2 | Service part / kit | PartsGeek |
| X-70-2 | Nut, hex | 4 | Service part / kit | PartsGeek |
Service, wear & replacement parts referenced for this model and its engine — confirm the exact part for your serial number. See the full parts catalog to search and cross-reference.
Fuel consumption
| Rating | Load | L/h | gal/h |
|---|---|---|---|
| Prime | |||
| Standby |
Available documents
Installation manual — 981-0621 Onan KY Installation Manual (5-2000)) (Cummins/Onan)Owner's manual — 0981-0132 (Cummins/Onan)Owner's manual — 900-0541B-energy-command-operation (Cummins/Onan)Parts manual — 0932-0112 Onan Post-Sale Literature Index (07-1998) (Cummins/Onan)Parts manual — 932-0109B Onan Engine & Genset Short Block Index (10-1998) (Cummins/Onan)Parts manual — 957-0220 Onan KR (spec T) Genset Parts manual (09-1979) (Cummins/Onan)Parts manual — 981-0238G Onan KV (spec A-L) KVC (spec A-C) KVD (spec A-B) Genset Parts catalog (01-2005) (Cummins/Onan)Parts manual — 981-0238G Onan KV (spec A-L) KVC (spec A-C) KVD (spec A-B) Genset Parts manual (01-2005) (Cummins/Onan)Parts manual — 981-0246 Onan KY (A-P) KYD (A-C) MicroLite 4000 series Parts catalog (12-2012) 43pgs (Cummins/Onan)Parts manual — 981-0246 Onan KY (spec A-P) KYD (spec A-C) RV Genset Parts Manual (12-2012) (Cummins/Onan)Parts manual — 981-0246B Onan KY (A-J) MicroLite 4000 series Parts catalog (06-1999) (Cummins/Onan)Parts manual — DK-Kohler (Cummins/Onan)Parts manual — F-1106A Cummins-Onan post-1990 Accessories & Service Support Catalog (02-2002) (Cummins/Onan)Parts manual — TM 5-6115-323-14 MEP-015A MEP-025A 1.5KW genset manual (Cummins/Onan)Service manual — 900-0543 Onan Energy Command 20 Operators Installation (1-2006) (Cummins/Onan)Service manual — 900-0605D Onan KV KVD Repair Times (Cummins/Onan)Service manual — 900-0606C Onan KY KYD Repair Times (Cummins/Onan)Service manual — 960-0510B Onan DGBB thru DGFC Series Service Manual (10-1998) (Cummins/Onan)Service manual — 981-0506 Onan KV (spec A-B) Microlite 2800 RV Genset Service manual (03-1991) (Cummins/Onan)Service manual — 981-0518E Onan KV (spec C) KVC KVD (spec A) RV Genset Service Manual (11-2004) (Cummins/Onan)Service manual — 981-0530C Onan KY (spec J) KYD (spec A) RV Genset Service Manual (01-2006) (Cummins/Onan)Service manual — F-1123 Cummins-Onan RV Generator Handbook (08-2007) (Cummins/Onan)Service manual — OnanKV KVC KVD Service (Cummins/Onan)Service manual — PG Parts Catalog1 (Cummins/Onan)