Home›Cummins/Onan›Cummins/Onan DEH Series

Cummins/Onan DEH Series Generator Set

The Cummins/Onan DEH Series is a 30 kW (37.5 kVA) Diesel standby generator set powered by a Ford DSD 442 engine. It is available at 110/220 V, 115/230 V, 120/240 V, 120/208 V, 220/380 V, 230/400 V, 240/416 V, 254/440 V, 277/480 V and 347/600 V, single-phase, 60 Hz and rated 156 A. It holds about 9 L (2.4 gal) of oil and 15 L (4.0 gal) of coolant. Starting uses 2 group-2 batteries at 12 V. The set measures 1680×840×1160 mm (66.1×33.1×45.7 in) and weighs about 771.1 kg (1700 lb).

30 kW
Standby
4.16 L
Displacement
9.0 L
Oil capacity
1
Document types

How to read your Cummins/Onan serial & model number →

Typical fuel consumption for 30–35 kW Diesel generators →

Compare with other 30–35 kW Diesel generators →

Specifications

FuelDiesel
Frequency60.0 Hz
Standby power30 kW
Standby kVA37
Prime power25 kW
ControllerFord-Dorset
Oil capacity9.0 L
AlternatorUR (4-pole)
Voltage options110/220 V, 115/230 V, 120/240 V, 120/208 V, 220/380 V, 230/400 V, 240/416 V, 254/440 V, 277/480 V, 347/600 V
Phase1
Rated current156 A
Power factor0.8
Battery group2H
Battery voltage12 V
Battery quantity2
Coolant capacity15.0 L
Dimensions (L×W×H)1680×840×1160 mm
Dry weight771 kg

Engine

Ford DSD 442
Oil capacity9.0 L
Coolant capacity15.0 L
Displacement4.16 L
AspirationNatural
Rated speed1800 rpm

Common questions

What is the power rating of the Cummins/Onan DEH Series?

The Cummins/Onan DEH Series is rated 30 kW standby (37.5 kVA).

Which engine powers the Cummins/Onan DEH Series?

The Cummins/Onan DEH Series is powered by the Ford DSD 442 engine.

Is the Cummins/Onan DEH Series diesel or gas?

The Cummins/Onan DEH Series runs on Diesel.

How much oil does the Cummins/Onan DEH Series take?

The Ford DSD 442 engine in the Cummins/Onan DEH Series has an oil capacity of 9.0 liters.

How much coolant does the Cummins/Onan DEH Series hold?

The Cummins/Onan DEH Series cooling system holds 15 liters (4.0 US gallons) for the radiator system including the engine, per the manufacturer specification sheet.

What is the prime power rating of the Cummins/Onan DEH Series?

The Cummins/Onan DEH Series is rated 25 kW prime (31 kVA), against 30 kW standby.

How much does the Cummins/Onan DEH Series weigh?

The Cummins/Onan DEH Series has a dry weight of 771 kg (1699 lb).

What voltage does the Cummins/Onan DEH Series produce?

The Cummins/Onan DEH Series is offered in 110/220 V, 115/230 V, 120/240 V, 120/208 V, 220/380 V, 230/400 V, 1-phase.

What size battery does the Cummins/Onan DEH Series need?

The Cummins/Onan DEH Series uses 2 batteryies, 12 V each, group 2H, per the manufacturer specification sheet.

Which alternator is fitted to the Cummins/Onan DEH Series?

The Cummins/Onan DEH Series uses a UR alternator. It has 4 poles.

Troubleshooting

6

Symptoms & remedies

SymptomRemedy
Engine stops cranking and fault lamp lights, after cranking approximately 75 seconds.See engine service manual for troubleshooting fuel system. After correcting problem, reset engine monitor relay by placing Run-Stop/Reset-Remote switch to Stop/Reset, then back to the required running position.
Fault lamp lights immediately after engine starts.Check for: Overspeed condition as engine starts.
Fault lamp lights and engine shuts down after running for a period.Check the following: a. Oil level. Engine will shut down if sensor is closed. b. Check engine manual for troubleshooting oil system. c. High engine temperature. Check coolant level; check water flow (city water cooled systems); check radiator for free air flow, and fan belts for tightness. See engine manual for troubleshooting cooling system. d. Check for faulty oil pressure sensor or faulty high engine temperature sensor.
Engine runs, shuts down and cranks for 75 seconds. Cranking cycle stops; fault lamp lights.Check fuel supply.
Fault lamp lights, no fault exists.To check a no-fault condition, disconnect leads from TB11 terminals 29, 30 and 31. If fault lamp lights with leads disconnected, replace engine monitor board. Reconne
Overcrank fault lamp lights and engine stops cranking after approximately 75 seconds.See engine service manual for troubleshooting fuel system. After correcting fault, reset engine monitor relay by placing Run-Stop/Reset-Remote switch to Stop/Reset position, depressing Reset button, then to the required running position.

Fault codes and symptom→remedy steps extracted from this model’s service/owner documentation; verify against the official manual before servicing. Full Cummins/Onan DEH Series troubleshooting guide (13 entries) →

Fuel consumption

RatingLoadL/hgal/h
Standby100%2.732.6

Available documents

Owner's manual — 976-0120 Onan DEH Operator's Manual (4-1980) (Cummins/Onan)

This page was generated from the 1 manufacturer document above by automated extraction; every figure shown is copied from one of them. How the data is compiled.