Service parts for the C11
Grouped by system, with how many of each the parts manual calls for.
Air intake
1 requiredFuel system
1 requiredOil system
1 requiredBelts
1 requiredCooling system
1 required119-5150Coolantfind
Hydraulic system
1 requiredPrices captured from merchant listings; some links are affiliate links. Confirm against your serial number before ordering.
Specifications
Ratings spec sheet not in our library yet — see the documents below.
Filters & service parts
model family| Item | Spec | Capacity | Part # | Interval | |
|---|---|---|---|---|---|
| Air filter | 106-3973 | Amazon eBay $79.98 eBay $39.31 NAPA $116.29 FridayParts $62.16 | |||
| Fuel filter | 1R0750 | Amazon eBay $33.80 eBay $33.80 NAPA $21.82 NAPA $21.82 KuduParts $17.00 FridayParts $29.50 | |||
| Oil filter | 1R0716 | Amazon eBay $44.90 eBay $44.90 NAPA $33.79 NAPA $33.79 KuduParts $80.00 FridayParts $81.99 | |||
| Battery | 12V, 950 CCA for 30 seconds at -18°C (0°F), 90 amp-hr @ 20 hours, 170 reserve capacity minutes | — | 18000 hr | ||
| Belt | 118-2018 | eBay $74.43 FridayParts $21.56 | |||
| Coolant | Caterpillar EC-1 specification; 1:1 premixed solution with distilled water | 119-5150 | 12000 hr | buy | |
| Coolant filter | Replace as needed based on condition. | — | |||
| Hydraulic filter | 093-7521 | eBay $29.99 NAPA $45.52 KuduParts $18.00 FridayParts $19.99 | |||
| Oil | SAE 30 or SAE 40; API CF-4 category; factory fill for 3116 and 3126 Marine Engines with mechanical unit injection | — | 500 hr | ||
| Spark plug | Replace every 200 hours or as needed based on condition. | — | 200 hr |
Compiled from this model's family documentation — may include parts for closely-related variants. Confirm the exact part for your serial number.
Service intervals
14| Item | Action | Hours | Months | Notes |
|---|---|---|---|---|
| Engine oil (S-O-S oil sample) | Test | 125 hr | Severe service occurs at high loads, in high temperatures, and in dusty conditions | |
| Coolant (S-O-S coolant analysis Level 1) | Test | 250 hr | Cat ELC - Every 250 Hours; also the recommended sampling interval for all conventional heavy-duty coolant/antifreeze and for commercial coolants that meet Cat EC-1 | |
| Engine crankcase oil (S-O-S oil sample) | Test | 250 hr | Table 6 S-O-S Oil Sampling Interval; severe applications may require a more frequent oil sampling interval | |
| Primary air filter element | Change | 250 hr | When changing the primary element at 250 operating hours (basis of the without-indicator filter-change comparison) | |
| SCA (Supplemental Coolant Additive) concentration | Test | 250 hr | Test the concentration of SCA or submit a coolant sample at 250 hour intervals or at PM Level 1 intervals; check at every oil change or every 250 hours, whichever occurs first | |
| Coolant (S-O-S coolant analysis Level 2) | Test | 500 hr | 12 mo | First service — For new systems, refilled systems, and converted systems that use Cat ELC or Cat DEAC; also every year; use the interval that occurs first |
| oil | Change | 500 hr | 3000 Series service intervals increased to 500 hours as standard (3013C, 3024C, 3054, 3056) | |
| Secondary air filter element | Change | 750 hr | When changing the secondary element at 750 operating hours (basis of the without-indicator filter-change comparison) | |
| Cat ELC Extender addition (cooling system) | Other | 6000 hr | Treat the cooling system with Cat ELC Extender at 6000 hours or one half of the coolant service life | |
| Coolant (Cat ELC) | Change | 12000 hr | 12000 service hours or six years; use the interval that occurs first | |
| minor overhaul | Other | 20000 hr | 3600 engines designed to run 20 000 hours between minor overhauls using No. 2 fuel | |
| major overhaul | Other | 40000 hr | 3600 engines designed to run 40 000 hours between major overhauls using No. 2 fuel | |
| cylinder liners and pistons | Other | 80000 hr | 3600 cylinder liners and pistons designed for 80 000 hours using No. 2 fuel | |
| Coolant (S-O-S coolant analysis Level 1 and Level 2) | Test | 12 mo | Cat DEAC - Yearly |
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Service specifications
12| Type | Item | Value | Unit | Condition |
|---|---|---|---|---|
| Other | Radiator cooling package design ambient temperature | 48.9 | °C (120° F) | with 50/50 water/Extended Life Coolant mixture |
| Other | Radiator cooling package maximum elevation | 1524 | m (5000 ft) | with 50/50 water/Extended Life Coolant mixture |
| Pressure | Maximum air pressure for cleaning purposes (deadheaded air nozzle with chip guarding and PPE) | 205 | kPa | |
| Pressure | Maximum air pressure for cleaning purposes (deadheaded air nozzle with chip guarding and PPE) | 30 | psi | |
| Pressure | Maximum water pressure for cleaning purposes | 275 | kPa | |
| Pressure | Maximum water pressure for cleaning purposes | 40 | psi | |
| Pressure | Unit injector fuel injection pressure | 1240 | bar (18 000 psi) | |
| Temperature | Maximum storage temperature for ether cylinders | 120 | °F | |
| Temperature | Maximum storage temperature for ether cylinders | 49 | °C | |
| Temperature | Maximum storage temperature for ether cylinders (Engine Starting section) | 102 | °F | |
| Temperature | Maximum storage temperature for ether cylinders (Engine Starting section) | 39 | °C | |
| Torque | Air compressor SAE "A" hydraulic pump drive maximum torque (374 L/min and 467 L/min compressors) | 60 | N•m (44 lb-ft) | C7, C9 ACERT |
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Recommended fluids
| Fluid | Grade | Standard | Ambient | Capacity | Notes |
|---|---|---|---|---|---|
| Coolant | 50/50 mixture water/Caterpillar Extended Life Coolant | below 48°C | Radiator cooling packages designed for up to 48.9° C (120° F) ambient; coolant sump refill capacities vary by oil sump/pan (18 L to 106 L service refill with new oil filter change) | ||
| Coolant | Cat DEAC | Diesel; 3,000 Service Hours or Three Years; annual S·O·SSM Level 2 coolant sampling and analysis | |||
| Coolant | Cat DEAC (Diesel Engine Antifreeze/Coolant) | Acceptable coolant; commercial heavy-duty antifreeze/coolant must meet ASTM D4985 or ASTM D6210 | Conventional heavy-duty coolant/antifreeze. Caterpillar recommends a 1:1 mixture of water and glycol. Do not use a commercial coolant/antifreeze that only meets the ASTM D3306 specification. Do not use Cat SCA at the initial fill when Cat DEAC is used. | ||
| Coolant | Cat ELC | Diesel; 12,000 Service Hours or Six Years; add Cat ELC Extender at 6,000 service hours or one half of service life; annual S·O·SSM Level 2 coolant sampling and analysis | |||
| Coolant | Cat ELC (Extended Life Coolant) | Caterpillar EC-1 specification (preferred); also meets ASTM D4985, ASTM D6210, and ASTM D3306 | Service life of 12000 service hours or six years. Premixed ELC provides freeze protection to -37 C (-34 F); ELC Concentrate can be used to lower the freezing point to -52 C (-62 F). An Extender is the only additional maintenance needed at 6000 service hours or one half of the ELC service life. Cat ELC cooling systems can withstand contamination to a maximum of ten percent of conventional heavy-duty coolant/antifreeze and/or SCA. | ||
| Coolant | Cat NGEC | Natural Gas; 16,000 Service Hours or Three Years; use interval that occurs first | |||
| Coolant | Cat SCA (Supplemental Coolant Additive) with water | SCA concentration in a cooling system that uses SCA and water should be six to eight percent by volume; do not exceed the eight percent maximum concentration. If Cat SCA is not used, the commercial SCA must provide a minimum of 2400 mg/L or 2400 ppm (140 grains/US gal) of nitrites in the final coolant mixture when used with water, and a minimum of 1400 mg/L or 1400 ppm (82 grains/US gal) with heavy-duty coolant/antifreeze. | |||
| Coolant | Glycol (ethylene glycol / propylene glycol) | Propylene glycol coolant must meet ASTM D6210-04 | Ethylene glycol: 50 percent = freeze protection -37 C (-34 F), boil protection 106 C (223 F); 60 percent = -52 C (-62 F), 111 C (232 F). Propylene glycol: 50 percent = -32 C (-26 F), 106 C (223 F). Do not use propylene glycol in concentrations that exceed 50 percent; do not use ethylene glycol in concentrations that exceed 60 percent. All Caterpillar diesel engines equipped with air-to-air aftercooling (ATAAC) require a minimum of 30 percent glycol. | ||
| Engine oil | Cat DEO (Diesel Engine Oil) 10W-30 and 15W-40 | Cat ECF-1 (exceeds); API CI-4, API CI-4 PLUS, API CH-4, API CG-4, API CF (Cat DEO SAE 15W-40) | Caterpillar oils are used to fill diesel engines at the factory. Non-Caterpillar commercial oils are second choice oils. Do not use API CF-4 oils in Caterpillar diesel engines. Do not use single grade API CF oils or multigrade API CF oils in 3500 Series, C175 Series and smaller DI diesel engines. | ||
| Engine oil | Cat NGEO | Natural Gas | |||
| Engine oil | Commercial oils (DI engines) | Cat ECF-1 required; API CG-4 multigrade acceptable; API CH-4, API CI-4 and API CI-4 PLUS acceptable only if the requirements of Cat ECF-1 are met; do not use API CF-4 oils | Minimum TBN must be 10 times the fuel sulfur level (ASTM D2896); minimum TBN of the oil is 5 regardless of a low fuel sulfur level. API CG-4 oils: do not exceed the standard oil drain interval. | ||
| Engine oil | Commercial oils (PC engines) | Cat ECF-1; API CH-4, API CI-4, API CI-4 PLUS (if Cat ECF-1 requirements met); API CG-4 multigrade; API CF-4 multigrade; API CF | Minimum TBN of the oil that is used in PC engines must be 20 times the fuel sulfur level; minimum TBN of new oil is five. Change the oil when the TBN deteriorates to 50 percent of the original TBN. | ||
| Engine oil | Re-refined base stock oils | Acceptable if they meet the performance requirements specified by Caterpillar; filtering is inadequate for producing high quality re-refined base stock oils. | |||
| Engine oil | Synthetic base stock oils | Acceptable if they meet the performance requirements specified for the engine compartment. Caterpillar does not recommend the automatic extension of oil drain intervals for any type of oil. | |||
| Engine oil | Cat Arctic DEO SYN SAE 0W-30 | -40°C to 30°C | Engine Crankcase; Industrial Engines | ||
| Engine oil | SAE 0W-20 | -40°C to 10°C | Table 1 Lubricant Viscosities for Ambient Temperatures (DI diesel engines) | ||
| Engine oil | SAE 0W-30 | -40°C to 30°C | Table 1 Lubricant Viscosities for Ambient Temperatures (DI diesel engines) | ||
| Engine oil | SAE 0W-40 | -40°C to 40°C | Table 1 Lubricant Viscosities for Ambient Temperatures (DI diesel engines) | ||
| Engine oil | Cat DEO SYN SAE 5W-40 | -30°C to 50°C | Engine Crankcase; Industrial Engines | ||
| Engine oil | SAE 5W-30 | -30°C to 30°C | Table 1 Lubricant Viscosities for Ambient Temperatures (DI diesel engines) | ||
| Engine oil | SAE 5W-40 | -30°C to 50°C | Table 1 Lubricant Viscosities for Ambient Temperatures (DI diesel engines) | ||
| Engine oil | Cat DEO SAE 10W-30 | -18°C to 40°C | Engine Crankcase; Industrial Engines | ||
| Engine oil | SAE 10W-30 | -18°C to 40°C | Table 1 Lubricant Viscosities for Ambient Temperatures (DI diesel engines); SAE 10W-30 is the preferred viscosity grade for the 3116, 3126, C7, C-9 and C9 diesel engines between -18 C (0 F) and 40 C (104 F) | ||
| Engine oil | SAE 10W-40 | -18°C to 50°C | Table 1 Lubricant Viscosities for Ambient Temperatures (DI diesel engines) | ||
| Engine oil | Cat DEO SAE 15W-40 | -9°C to 50°C | Engine Crankcase; Industrial Engines | ||
| Engine oil | SAE 15W-40 | -9°C to 50°C | Table 1 Lubricant Viscosities for Ambient Temperatures (DI diesel engines) | ||
| Engine oil | Cat SAEO SAE 30 | API CF-4 category | 0°C to 40°C | Table 2 - 3116 and 3126 Marine Engines with mechanical unit injection; factory fill has API CF-4 category and viscosity grade of SAE 30 | |
| Engine oil | SAE 30 | 0°C to 40°C | Table 3 Lubricant Viscosities for Ambient Temperatures - PC engines only | ||
| Engine oil | Cat SAEO SAE 40 | API CF-4 category | 5°C to 50°C | Table 2 - 3116 and 3126 Marine Engines with mechanical unit injection. Caterpillar does not recommend the use of multigrade oils in the 3116 and 3126 Marine Diesel Engines that use mechanical unit injection. | |
| Engine oil | SAE 40 | 5°C to 50°C | Table 3 Lubricant Viscosities for Ambient Temperatures - PC engines only |
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Procedures
3Determining the cause of a plugged fuel filter (ice or wax) diagnostic
- Remove the fuel filters.
- Cut the fuel filters open.
- Inspect the fuel filter before the filter warms. The inspection will show that the filter is filled with particles of either ice or wax.
Changing to Cat ELC maintenance
⚠ Do not leave an empty SCA maintenance element on a system that is filled with ELC. The element housing may corrode and leak causing an engine failure.
⚠ Improper or incomplete rinsing of the cooling system can result in damage to copper and other metal components.
⚠ The cooling system cleaner must be thoroughly flushed from the cooling system. Cooling system cleaner that is left in the system will contaminate the coolant. The cleaner may also corrode the cooling system.
Tools: Caterpillar cleaner for cooling systems, 5P-3413 Pipe Sealant, Suitable containers to collect fluids
- Drain the coolant into a suitable container.
- Dispose of the coolant according to local regulations.
- If equipped, remove the empty SCA maintenance element and the element base. Plug the coolant lines or bypass the coolant lines.
- Flush the system with clean water in order to remove any debris.
- Use Caterpillar cleaner for cooling systems in order to clean the system. Follow the instructions on the label.
- Drain the cleaner into a suitable container. Flush the cooling system with clean water.
- In systems with heavy deposits, disconnect the hoses. Clean deposits and debris from the hoses and fittings. Install the hoses and tighten the hose fittings.
- Fill the cooling system with clean water and operate the engine until the engine is warmed to 49 C to 66 C (120 F to 151 F).
- Drain the cooling system into a suitable container and flush the cooling system with clean water.
- Repeat Steps 8 and 9 until the system is completely clean.
- Fill the cooling system with the Cat ELC.
- Operate the engine until the engine is warmed. While the engine is running, inspect the engine for leaks. Tighten hose clamps and connections in order to stop any leaks.
- Attach the Special Publication, PEEP5027, "Label" to the cooling system filler for the engine in order to indicate the use of Cat ELC.
Calculating the amount of lighter fuel required to modify the cloud point or the pour point operation
- Obtain the specification for the cloud point or the pour point of both fuels from your fuel supplier.
- Locate the cloud point or the pour point of the heavier fuel on the left side of the table. Mark the point on the table.
- Locate the cloud point or the pour point of the lighter fuel on the right side of the table. Mark the point on the table.
- Draw a line between the two points that were established. Label this line "A".
- Find the lowest outside temperature for machine operation on the left side of the table. Draw a horizontal line from this point until it intersects line "A". Label this new line "C".
- Mark the intersection of line "C" and line "A". Draw a vertical line to the bottom of the table. Label this line "B". The point at the bottom of line "B" reveals the percentage of lighter fuel that is
Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.
Common questions
Which oil filter part number does the Caterpillar C11 take?
The Caterpillar C11 uses oil filter part number 1R0716.
What fuel filter does the Caterpillar C11 use?
The Caterpillar C11 uses fuel filter part number 1R0750.
Which air filter part number does the Caterpillar C11 take?
The Caterpillar C11 uses air filter part number 106-3973.
Parts
250model familyCompiled from this model's family documentation — may include parts for closely-related variants. Confirm the exact part for your serial number. See the full parts catalog to search and cross-reference.
Available documents
Engine spec — C11 (Caterpillar)Engine spec — EnginesWithPureAttitude (Caterpillar)Engine spec — LECH3874-02 (Caterpillar)Engine spec — LEDT3135-01 (Caterpillar)Engine spec — cat-c11-spec-sheet (Caterpillar)Reference — ledh6161 attachments guide (Caterpillar)Owner's manual — C11, C13 and C15 On-highway Engines-Engine Safety (Caterpillar)Parts manual — Caterpillar Engines (Caterpillar)Parts manual — KMP-Brand®Parts-Guide-Suitable-for-Caterpillar®By-Product (Caterpillar)Parts manual — LFDH6161-00 HR (Caterpillar)Service manual — Caterpillar Diesel Engine Fluid Recommendations (Caterpillar)
This page was generated from the 11 manufacturer documents above by automated extraction; every figure shown is copied from one of them. How the data is compiled.