Home›Engines›Perkins 404D-22TG

Perkins 404D-22TG Engine

Name: Perkins 404D-22TG Engine
Brand: Perkins

The Perkins 404D-22TG is a 2.2 L 4-cylinder turbo engine rated at 1500 rpm, producing up to 34.58 kW. It powers generator sets from AKSA, Aurora Generators, Knox/Knoxgen and Perkins, including the AD44, AGi25P-E, AGi28P and KDE-35P-60. It holds 10.6 L (2.8 gal) of oil and 9.3 L (2.5 gal) of coolant.

Also known as: Perkins 404D-22TG

Part of the Perkins 404D engine family — 8 variants share parts & fitment.

2.2 L

Displacement

Cylinders

1500 rpm

Rated speed

34 kW

Gross power

On this pageService parts Specs Generator sets Maintenance Filter cross-reference FAQ Service intervals Torque & specs Fluids Procedures

Service parts for the 404D-22TG

The cheapest captured merchant offer per filter — see the full cross-reference below for every OEM/aftermarket option.

Fuel system

1 required

26560140Fuel filter$13.26eBay

Oil system

1 required

915155Oil filter$7.98PartsGeek

Prices captured from merchant listings; some links are affiliate links. Verify against your serial number before ordering.

Engine specifications

Oil capacity	10.6 L
Coolant capacity	9.3 L
Displacement	2.2 L
Cylinders	4
Aspiration	Turbo
Rated speed	1500 rpm
Gross power	34 kW

Generator sets powered by this engine

Shared across brands: AKSA, Aurora Generators, Knox/Knoxgen, Perkins

AKSA AD44 Aurora Generators AGi25P-E Aurora Generators AGi28P Knox/Knoxgen KDE-35P-60 Perkins 404D-22TPerkins PMI184FPerkins PMI24P

How to read your Perkins engine serial & model number →

Maintenance schedule

Item	Spec	Capacity	Part #	Interval
Air filter			—
Fuel filter			26560140		Amazon eBay $13.26 KuduParts $18.00
Oil filter			915155	500 hr	Amazon $47.90 eBay $13.49 PartsGeek $7.98
Battery			—
Belt			—
Coolant		9.32 L	—
Oil	500 hr oil change interval	10.6 gal / L	—	500 hr
Spark plug			—

Pooled from every document that names this exact engine — confirm the interval and part number against your unit's serial number.

Service intervals

Item	Action	Hours	Months	Notes
alternator and fan belt tension	Check	20 hr		When new belts are installed, check the belt tension again after 20 hours of engine operation
Agua y sedimentos del tanque de combustible	Drain	50 hr		Cada 50 horas de servicio o cada semana
Fuel Tank Water and Sediment	Drain	50 hr		or Weekly
Alternator and Fan Belts	Adjust	250 hr	6 mo	Every 250 Service Hours or 6 Months - Inspect/Adjust
Alternator and Fan Belts	Inspect	250 hr	6 mo	or adjust
Correas del alternador y del ventilador	Inspect	250 hr	6 mo	Inspeccionar/Ajustar
Aceite y filtro del motor	Change	500 hr	12 mo	Cambiar
Aditivo de refrigerante suplementario (SCA) del sistema de enfriamiento	Check	500 hr	12 mo	Comprobar/Añadir
Battery Electrolyte Level	Check	500 hr	12 mo	Every 500 Service Hours or 1 Year
Cooling System Supplemental Coolant Additive (SCA)	Test	500 hr	12 mo	or add
Elemento del filtro de aire del motor (Elemento doble)	Clean	500 hr	12 mo	Limpiar/reemplazar
Elemento del filtro de aire del motor (elemento sencillo)	Inspect	500 hr	12 mo	Inspeccionar/Reemplazar
Engine Air Cleaner Element	Replace	500 hr	12 mo	Every 500 Service Hours or 1 Year
Engine Air Cleaner Element (Dual Element)	Clean	500 hr	12 mo	or replace
Engine Air Cleaner Element (Single Element)	Inspect	500 hr	12 mo	or replace
Engine Oil and Filter	Change	500 hr	12 mo	Every 500 Service Hours or 1 Year
Filtro del Sistema de Combustible	Replace	500 hr
Fuel System Filter	Replace	500 hr	12 mo	Every 500 Service Hours or 1 Year
Fuel System Primary Filter	Replace	500 hr	12 mo	Every 500 Service Hours or 1 Year
Hoses and Clamps	Inspect	500 hr	12 mo	or replace
Hoses and Clamps	Replace	500 hr	12 mo	Every 500 Service Hours or 1 Year - Inspect/Replace
Mangueras y abrazaderas	Inspect	500 hr	12 mo	Inspeccionar/Reemplazar
Nivel del electrólito de la batería	Check	500 hr	12 mo
Radiador	Clean	500 hr	12 mo	Limpiar
Radiator	Clean	500 hr	12 mo	Every 500 Service Hours or 1 Year
Alternator and Fan Belts	Replace	1000 hr		Every 1000 Service Hours
Correas del alternador y del ventilador	Replace	1000 hr
Engine Valve Lash	Adjust	1000 hr		Every 1000 Service Hours - Inspect/Adjust
Engine Valve Lash	Inspect	1000 hr		or adjust
Luz de las válvulas del motor	Adjust	1000 hr		Inspeccionar/Ajustar
Turbocharger	Inspect	1000 hr		Every 1000 Service Hours (if equipped)
Turbocompresor	Inspect	1000 hr
Aftercooler Core	Inspect	2000 hr		Every 2000 Service Hours
Alternador	Inspect	2000 hr
Alternator	Inspect	2000 hr		Every 2000 Service Hours
Engine Crankcase Breather	Replace	2000 hr		Every 2000 Service Hours
Engine Mounts	Inspect	2000 hr		Every 2000 Service Hours
Motor de arranque	Inspect	2000 hr
Núcleo del posenfriador	Inspect	2000 hr
Respiradero del Cárter	Replace	2000 hr

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Service specifications

Type	Item	Value	Unit	Condition
Clearance	Connecting rod parallel alignment (length B) difference	± 0.08 (± 0.0031 inch)	mm	measured 100 mm (3.94 inch) from the connecting rod
Clearance	Fuel injection pump shim - use beaded shims	0.5 (0.0197 inch) or below	mm	beading faces upward toward bottom of fuel injection pump
Clearance	Measurement (B) between C-clip and collar (oil pump)	0.10 to 0.15 (0.004 to 0.006 inch) new; not more than 0.20 (0.008 inch) used	mm
Clearance	Tooling (A) dial indicator reading for fuel rack position	2.00 ± 0.01 (0.0787 ± 0.0004 inch)	mm	governor adjustment procedure
Clearance	Valve head lift for valve guide radial check	15.0 (0.60 inch)	mm
Gap	Flywheel face runout	0.03 (0.001 inch)	mm	for every 25 mm (1.0 inch) of flywheel radius
Gap	Flywheel housing bore runout (radial eccentricity)	0.20 (0.008 inch) SAE 5; 0.23 (0.009 inch) SAE 4	mm	maximum difference of four readings
Gap	Flywheel housing face runout (axial eccentricity)	0.20 (0.008 inch) SAE 5; 0.23 (0.009 inch) SAE 4	mm	maximum difference of four readings
Gap	Flywheel runout	0.20 (0.008 inch)	mm	maximum difference of four 90-degree readings
Injection timing	Injection timing change per shim thickness difference	1 degree per 0.10 mm	degree	thicker shim retards timing
Other	Alternator and fan belt tension (new belt)	400 to 489	N (90 to 110 lb)	new belt
Other	Alternator and fan belt tension (used belt)	267 to 356	N (60 to 80 lb)	used belt operated 30 minutes or more at rated speed
Other	Aspiration	NA (Naturally Aspirated)
Other	Aspiration	T (Turbocharged)
Other	Aspiration	TA (Turbocharged aftercooled)
Other	Bead diameter of Tooling (A) on fuel injector threads	2	mm (0.08 inch)	Fuel injector installation
Other	Bead length of Tooling (A) on fuel injector threads	6	mm (0.25 inch)	Fuel injector installation
Other	Belt tension (new belt)	400-489	N	new belt
Other	Belt tension (used belt)	267-356	N	used belt after 30 minutes at rated speed
Other	Bore	67	mm (2.64 inch)
Other	Bore	77	mm (3.03 inch)
Other	Bore	84	mm (3.31 inch)
Other	Charging current after ten minutes of engine operation	approximately 10	amperes	high idle
Other	Compression Ratio	22.5:1
Other	Compression Ratio	23.1:1
Other	Compression Ratio	23.3:1
Other	Compression Ratio	23.5:1
Other	Compression Ratio	23:1
Other	Cylinders and Arrangement	In-Line four cylinder
Other	Cylinders and Arrangement	In-Line three cylinder
Other	Cylinders and Arrangement	In-Line two cylinder
Other	Displacement	0.507	L (30.939 in3)
Other	Displacement	0.762	L (46.500 in3)
Other	Displacement	1.131	L (69.018 in3)
Other	Displacement	1.496	L (91.291 in3)
Other	Displacement	1.508	L (92.024 in3)
Other	Displacement	1.66	L (101.3 in3)
Other	Displacement	2.216	L (135.229 in3)
Other	Engine oil pressure switch current	0.30 to 0.40 (replace if greater than 0.42)	amperes	12 volt battery power source
Other	Firing Order	1-2
Other	Firing Order	1-2-3
Other	Firing Order	1-3-4-2
Other	Fuel injector nozzle spray angle	4 degrees from the vertical	degrees	when the nozzle is fully open
Other	Fuel shutoff solenoid current	1.0 ± 0.1	amperes
Other	Glow plug current after 6 seconds	11.5 ± 1.5	amperes
Other	Glow plug current after 6 seconds	8.5	amperes
Other	Glow plug maximum current	11	amperes
Other	Glow plug maximum current	110	amperes
Other	Injection	Indirect
Other	Orden de encendido	1-2
Other	Orden de encendido	1-2-3
Other	Orden de encendido	1-3-4-2
Other	Relación de compresión	22,5:1
Other	Relación de compresión	23,1:1
Other	Relación de compresión	23,3:1
Other	Relación de compresión	23,5:1
Other	Relación de compresión	23:1
Other	Rotation viewed from the flywheel	Counterclockwise
Other	SCA concentration	6-8	%
Other	Stroke	100	mm (3.94 inch)

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Recommended fluids

Fluid	Grade	Standard	Ambient	Notes
Coolant	Anticongelante comercial de servicio pesado	ASTM D4985		Aceptable; puede requerir tratamiento con SCA; vida útil 3.000 horas o dos años
Coolant	Commercial Heavy-Duty Antifreeze	ASTM D4985		Acceptable. Service life 3000 hours or 2 years.
Coolant	ELC Perkins (Refrigerante de larga duración) - mezcla 1:1 agua/glicol			Preferido; premezclado protege contra congelación a -36°C (-33°F); vida útil 6.000 horas o tres años
Coolant	Glicol etilénico 50%			Protección contra congelación a -36°C (-33°F); 60% = -51°C (-60°F)
Coolant	Glicol propilénico 50%			Protección contra congelación a -29°C (-20°F); no exceder 50%
Coolant	Perkins ELC			Preferred. 1:1 premixed with distilled water. Freeze protection to -36°C (-33°F). Service life 6000 hours or 3 years.
Coolant	Ethylene Glycol 60%		above -51°C	Freeze protection -51°C (-60°F)
Coolant	Ethylene Glycol 50%		above -36°C	Freeze protection -36°C (-33°F)
Coolant	Perkins ELC (Extended Life Coolant)	Preferred; acceptable commercial heavy-duty antifreeze meeting ASTM D6210	above -36°C	1:1 mixture of water and glycol recommended (may be increased to 1:2 water to glycol). Premixed ELC freeze protection to -36 C (-33 F). Do not use coolant meeting only ASTM D3306.
Coolant	Propylene Glycol 50%		above -29°C	Freeze protection -29°C (-20°F)
Engine oil	API CH-4 minimum multigrade oil	API CH-4; API CI-4; ACEA E3		An oil specification above CH-4 is acceptable. Minimum TBN of new oil is 5; TBN must be 10 times fuel sulfur level.
Engine oil	SAE 0W20	EMA DHD-1 or API CH-4	-40°C to 10°C
Engine oil	SAE 0W30	EMA DHD-1 or API CH-4	-40°C to 30°C
Engine oil	SAE 0W40	EMA DHD-1 or API CH-4	-40°C to 40°C
Engine oil	SAE 0W20, 0W30, 0W40, 5W30, 5W40	EMA DHD-1 Recommended Guideline (first choice)	-30°C to -20°C	Lubricants for cold weather (ambient below -20 C; below -30 C use synthetic base stock with pour point lower than -50 C).
Engine oil	SAE 5W30	EMA DHD-1 or API CH-4	-30°C to 30°C
Engine oil	SAE 5W40	EMA DHD-1 or API CH-4	-30°C to 40°C
Engine oil	SAE 10W30	EMA DHD-1 or API CH-4	-20°C to 40°C
Engine oil	SAE 15W40	EMA DHD-1 or API CH-4	-10°C to 50°C
Fuel	Biodiesel	EN14214 or ASTM D675		Maximum 10% mixture with mineral diesel fuel; not recommended for standby generator sets.
Fuel	Combustible diesel destilado (Grupo 1 preferido)	EN590 / ASTM D975 / JIS K2204 / BS2869 Clase A2		Número de cetano mínimo 40; azufre <0,5%; viscosidad cinemática 1,4 a 4,5 mm2/s en la bomba de inyección
Fuel	Diesel	Perkins Specification for Distillate Diesel Fuel		Cetane minimum 40; Sulfur max 15 ppm (ULSD) or 500 ppm (LSD); Viscosity 1.4-4.5 cSt; Density 801-876 kg/m3 at 15°C; Lubricity max 0.46 mm; Cloud point must not exceed lowest expected ambient temperature.
Fuel	Distillate diesel fuel	Perkins Specification for Distillate Diesel Fuel (tables 24, 25, 26)		Sulfur per emissions regulations (ULSD <=15 ppm; LSD <=500 ppm). Cetane number 40 minimum. Lubricity wear scar diameter 0.46 mm maximum. Kinematic viscosity 1.4 to 4.5 cSt at fuel injection pump. Density 801-876 kg/m3.
Other		SAE J-967 (ISO 4113) oil equivalent		Calibration fluid used when testing fuel injectors

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Procedures

Correas del alternador y del ventilador - Ajustar adjustment

⚠ Reemplace las correas de impulsión múltiples en conjuntos

Tools: Medidor Burroughs

Afloje los pernos de montaje (2) y el perno de ajuste (1).
Mueva el alternador para aumentar o disminuir la tensión de la correa.
Apriete el perno de ajuste (1). Apriete los pernos de montaje (2).
Compruebe otra vez la tensión de las correas después de 20 horas de operación cuando se instalen correas nuevas.

Engine Valve Lash - Inspect/Adjust adjustment

⚠ Hot engine components can cause burns; allow the engine to cool.

⚠ Only qualified service personnel should perform this maintenance.

Ensure that the engine cannot be started while this maintenance is performed.
Ensure that the engine is stopped before measuring the valve lash.
Measure and adjust the valve lash clearance. The lash can be inspected and adjusted hot or cold.
Refer to Systems Operation, Testing and Adjusting, Engine Valve Lash - Inspect/Adjust for the complete procedure.

Finding Top Center Position for No. 1 Piston adjustment

Remove the valve mechanism cover.
Remove the glow plugs.
Rotate the crankshaft until the No. 1 exhaust valve is nearly closed and the No. 1 inlet valve is starting to open.
Rotate the crankshaft approximately 360 degrees and align the timing mark on the crankshaft pulley with the TOP mark on the timing case.
Install the glow plugs.
Install the valve mechanism cover.

Fuel Injection Timing - Check adjustment

⚠ Old shims must not be reused.

Fuel injection timing is set at the factory and cannot change during operation.
If a fuel injection pump is removed, replace the old shims with new shims of the same thickness.
Select the correct combination of shims for the engine model from the shim tables.
If the original shim thickness cannot be determined, contact the Dealer Solution Network with the full engine number.

Gear Group (Front) - Time adjustment

Align timing mark (X) on the idler gear with the timing mark on the crankshaft gear.
Align timing mark (X) on the idler gear with the timing mark on the camshaft gear.

Governor - Adjust (Record the Governor Settings) adjustment

⚠ The engine must be in running condition in order to carry out the governor adjustment procedure.

⚠ If the engine is fitted with a Boost Compensation Device contact an authorized Perkins distributor.

Tools: 21825617 Dial Indicator graduated in 0.01 mm (0.0004 inch), Extension 20 mm (0.787 inch) long, 27610331 Dial holder, 27610332 Adapter for the cylinder block, 27610333 Calibration spring, Allen head screw M4 x 20 mm x 0.70, Optical Tachometer

Operate the engine until the normal operating temperature is reached.
Use an optical tachometer to record the engine rpm at low idle.
Accelerate the engine to high idle; record the engine rpm as Speed A.
Remove tamper proof caps.
Record protrusion X of the high idle stop screw and protrusion Y of the low idle stop screw.
Release locknut (3); turn high idle trimmer screw (2) four turns counterclockwise and tighten locknut.
Accelerate the engine to high idle; record the engine rpm as Speed B.

Alternator - Test diagnostic

⚠ Never disconnect any charging unit circuit or battery circuit cable from the battery when the charging unit is operated.

Tools: multimeter, ammeter

Put the multimeter positive lead on the Bat terminal; negative lead on ground or frame.
Put an ammeter around the positive output wire of the alternator.
Turn off all electrical accessories; turn off the fuel to the engine.
Operate the starter motor for 30 seconds; wait two minutes to cool the starter motor.
Start the engine and run at high idle.
Check output current; initial charging current should equal or exceed minimum full load current.
After approximately ten minutes, output voltage should be 14.0 ± 0.5 volts.
After ten minutes the charging current should decrease to approximately 10 amperes.

Compression - Test diagnostic

⚠ Keep the engine rpm constant for all cylinders when taking a compression reading.

⚠ Measure the compression on all of the cylinders.

Tools: compression gauge

Remove the fuel injector from the cylinder to measure compression for that cylinder.
Connect a suitable compression gauge to the cylinder.
Disconnect the fuel shutoff solenoid.
Operate the starter motor and record the pressure on the compression gauge.
Repeat for each cylinder.
Repair procedures must be taken if the compression is lower than the repair limit.

Engine Oil Pressure - Test diagnostic

Tools: suitable oil pressure gauge

Ensure the engine is filled to the correct oil level.
Connect a suitable gauge to a pressure tap location for engine oil.
Operate the engine and allow it to obtain normal operating temperature.
Keep the oil temperature constant with the engine at the rated rpm; read the pressure gauge.
Refer to the oil pressure table to determine if the oil pressure is in tolerance.

Fuel Injector - Leakage Test diagnostic

⚠ Always wear eye protection; test fluid under pressure can pierce the skin.

Tools: nozzle tester, adapter, tube assembly, extension, fuel collector, filter

Connect the fuel injector to suitable tooling with the spray directed into the extension and fuel collector.
Pump the pressure to about 2030 kPa (294 psi) below the opening pressure of the fuel injector.
Release the handle and note the time for pressure to decrease to approximately 0 kPa (0 psi).
If the time is less than 5 seconds or more than 45 seconds, the fuel injector is faulty.
Pump pressure to about 2030 kPa (294 psi) below opening pressure; fuel should not drip from the tip for at least ten seconds.
Replace the fuel injector if the results are not acceptable.

Fuel Injector - Test diagnostic

Run the engine at low idle.
Perform the test procedures to determine if a fuel injector does not work correctly.
Identify the suspect fuel injector.

Fuel System - Inspect diagnostic

Check fuel level in the fuel tank; ensure the fuel cap vent is not filled with dirt.
Check all fuel lines for leakage, restrictions, faulty bends; verify the return line is not collapsed.
Inspect the fuel filter for excessive contamination; install a new fuel filter if necessary.
Service the primary fuel filter, if equipped.
Operate the hand priming pump; inspect the fuel pressure regulating valve if resistance is felt.
Remove any air in the fuel system; refer to Fuel System - Prime.

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Parts cataloged across the Perkins 404D family

Part #	Description	Category
SSBU8311-03	Ajuste del juego de las válvulas (escape)	adjustment
LLB1114B	Leroy Somer	alternator
LLB1114D	Leroy Somer	alternator
LLB1114F	Leroy Somer	alternator
LLB1114L	Leroy Somer	alternator
LLB1114M	Leroy Somer	alternator
LLB1514J	Leroy Somer	alternator
LLB1514P	Leroy Somer	alternator
LLB3114D	Leroy Somer	alternator
LLB3114H	Leroy Somer	alternator
g01302737	Fuel Filter Base - Remove and Install (403A-15, 403D-15, 403D-15T, 403D-17, 404A-22, 404D-22, 404D-22T, and 404D-22TA Engines)	fuel_filter
i02959949	Fuel Filter Base - Remove and Install (403D-11, 403D-15, 403D-15T, 403D-17, 404D-15, 404D-22, 404D-22T and 404D-22TA Engines)	fuel_filter
i06755215	Fuel Filter Base - Remove and Install (403A-11, 403D-11, 403A-15, 403D-15, 403D-15T, 403D-17, 404D-15, 404A-22, 404D-22, 404D-22T, and 404D-22TA Engines)	fuel_filter
110996920	PERKINS 404D-22, 404D-22DT, 404C-22, 404C-22T, 104-19, 104-22 OIL PAN GASKET	gasket
111147741	PERKINS 404D-22 CYL HEAD GASKET 0.4MM	gasket
111996401	PERKINS 404D-22, 404D-22T, 404D-22TA, 404C-22, 404C-22T, 403D-17 VALVE COVER GASKET	gasket
404D-22TA	OIL FILTER	oil_filter
0213/IT	CAE Enclosure	other_service
1287339GT	Platform Control Box Mounting Fasteners	other_service
131437381	Shim, beaded, 0.2 mm	other_service
131437391	Shim, beaded, 0.3 mm	other_service
131437401	Shim, beaded, 0.4 mm	other_service
131437411	Shim, beaded, 0.5 mm	other_service
131437470	Shim, non-beaded, 0.5 mm	other_service
1314374700	Shim, beaded, 0.5 mm	other_service
131437490	Shim, beaded, 0.2 mm	other_service
131437500	Shim, beaded, 0.3 mm	other_service
131437510	Shim, beaded, 0.4 mm	other_service
131437520	Shim, beaded, 0.5 mm	other_service
131437530	Shim, non-beaded, 0.5 mm	other_service
131437541	Shim, beaded, 0.2 mm	other_service
131437551	Shim, beaded, 0.3 mm	other_service
131437561	Shim, beaded, 0.4 mm	other_service
131437571	Shim, beaded, 0.5 mm	other_service
131437580	Shim, non-beaded, 0.5 mm	other_service
131437590	Shim, beaded, 0.2 mm	other_service
131437600	Shim, beaded, 0.3 mm	other_service
131437610	Shim, beaded, 0.4 mm	other_service
131437620	Shim, beaded, 0.5 mm	other_service
131437630	Shim, non-beaded, 0.5 mm	other_service
131437670	Shim, beaded, 0.2 mm	other_service
131437680	Shim, beaded, 0.3 mm	other_service
131437690	Shim, beaded, 0.4 mm	other_service
131437710	Shim, non-beaded, 0.5 mm	other_service
1734115	POWERPART Lay-Up 3	other_service
1762811	POWERPART Lay-Up 2	other_service
CAERANGE/0510/PTB	Canópia Acústica CAE Modular	other_service
LL1014N	Industrial	other_service
M1001050	CUSCINETTO	other_service
M105112270	GUARNIZIONE (L=MT.1)	other_service
M107301390	ANELLO	other_service
M107509005	GUARNIZIONE	other_service
M282008222	COPERTURA ALTERNATORE	other_service
M307803101	TRAVERSA ALTERNATORE	other_service
M307806010	CONVOGLIATORE GENERATORE	other_service
M364108224	STAFFA	other_service
M6050050	ANELLO SEEGER	other_service
M764402200	MOTORE PERKINS 404C-22G 50Hz	other_service
M764403010	CARCASSA STATORE	other_service
M764403020	STATORE AVV. 400T230M110M CTE 50Hz	other_service
M764403030	ALBERO ROTORE	other_service
M764408066	CORNICE RADIATORE	other_service
M764412200	MOTORE PERKINS 404D-22G 50Hz	other_service
M764422200	MOTORE PERKINS 404C-22G 60Hz	other_service
M764423020	STATORE AVV. 400T230M110M CTE 60Hz	other_service
M764432200	MOTORE PERKINS 404D-22G 60Hz	other_service
M765006020	VENTOLA PER GENERATORE	other_service
M773713012	DISCO ALBERO ROTORE	other_service
M841562212	TUBO SCARICO OLIO	other_service
P200-2	Silenciador	other_service
P26-1S	Two large doors on each side	other_service
R250	IP23	other_service
i02590436	Model View Illustrations	other_service
i02645719	Fuel Transfer Pump - Remove and Install (Electrical Fuel Transfer Pump)	pump
i02645722	Fuel Transfer Pump - Remove and Install (Mechanical Fuel Transfer Pump)	pump
g01334429	Left side view of the 404D-22T Turbocharged engine	turbocharger
g01334477	Right side view of the 404D-22T Turbocharged engine	turbocharger
404D-15	Exhaust valves	valve
404D-22	Inlet valves	valve

Parts cataloged across all variants of this engine family — verify the exact part fits your specific variant and serial number before ordering.

Filters for this engine

Fuel filter: Perkins 26560140 Donaldson P551423 Wix WF10091
Oil filter: Perkins 915155 Donaldson P550335 Wix 51348 Ac Delco SR

Cross-referenced via Donaldson + OEM/engine-maker interchange — options to verify against your serial number, not confirmed for every exact variant.

Also used in

Jcb 1CX — Backhoe Loader
Miller Electric BIG BLUE 400 — Welder
Wacker Neuson ET65 — Excavator Tracked
Wacker Neuson EW65 — Excavator Wheeled
Wacker Neuson EZ53 — Excavator Tracked
Wacker Neuson EZ80 — Excavator Tracked
Wacker Neuson WL28 — Loader Wheeled
Wacker Neuson WL32 — Loader Wheeled
Wacker Neuson WL34 — Loader Wheeled
Wacker Neuson WL38 — Loader Wheeled
Wacker Neuson WL44 — Loader Wheeled
Weidemann 1370CX50 — Telehandler

Other equipment known to use this engine, via filter-application cross-reference — useful for sourcing parts even when your exact machine isn't listed elsewhere on this page.

Common questions

What is the oil capacity of the Perkins 404D-22TG?

The Perkins 404D-22TG engine has an oil capacity of 10.6 liters.

What is the displacement of the Perkins 404D-22TG?

The Perkins 404D-22TG has a displacement of 2.2 liters with 4 cylinders.

Which generators use the Perkins 404D-22TG engine?

The Perkins 404D-22TG powers 7 generator set(s), including AKSA AD44, Aurora Generators AGi25P-E, Aurora Generators AGi28P, Knox/Knoxgen KDE-35P-60, Perkins 404D-22T.

What oil filter does the Perkins 404D-22TG use?

The Perkins 404D-22TG uses oil filter part numbers Perkins 915155, Donaldson P550335, Wix 51348.

What fuel filter does the Perkins 404D-22TG use?

The Perkins 404D-22TG uses fuel filter part numbers Perkins 26560140, Donaldson P551423, Wix WF10091.

How often should you change the oil in the Perkins 404D-22TG?

The Perkins 404D-22TG oil change interval is every 500 hours.