Kohler KD Series Engine

⚠ Hazardous voltage. Moving parts. Operate only when all guards and electrical enclosures are in place.

Tools: sonic tension meter, wrench

1. Disable generator set and remove from service.
2. Remove fan guard rear face panel; inspect fan drive belt and replace if damaged or worn.
3. Check fan belt tension using sonic tension meter or belt deflection method.
4. Loosen four 3/4 in. undercarriage bolts.
5. Adjust tensioner pulley along tensioner slots via lead screw.
6. Adjust until belt tension falls into range listed in Figure 24.
7. Check pulley alignment on fan shaft; adjust fan sheaves and tensioner sheaves.
8. Tighten 3/4 in. undercarriage bolts; reinstall belt guards; reconnect battery; test run.

1. Disable generator set and remove from service.
2. For standard-duty filters: loosen clamp, remove element from air intake elbow, replace, tighten clamp.
3. For heavy-duty filters: release cover clips (KD2000-KD2500) or remove wingnut (KD2800-KD4000), remove cover.
4. Remove filter element.
5. Clean internal components with damp cloth.
6. Install new element.
7. Replace cover; for KD2000-KD2500 point dust ejector downward.

⚠ Sulfuric acid in batteries. Wear protective goggles and clothing.

Tools: wire brush

1. Clean battery and cables and tighten terminals according to service schedule.
2. Wipe battery with damp cloth; keep connections dry and tight.
3. If corrosion exists, disconnect cables and remove corrosion with wire brush.
4. Clean battery and cables with baking soda and water solution; do not allow solution to enter cells.
5. Flush with clean water and wipe with dry cloth.
6. After reconnecting cables, coat terminals with petroleum jelly, silicon grease, or other nonconductive grease.

⚠ Hot coolant and steam. Stop generator set and allow to cool before removing pressure cap.

1. Disable generator set and remove from service.
2. Allow engine to cool.
3. Remove pressure cap to allow system to drain and prevent air pockets.
4. Open radiator and/or engine block coolant drain valve(s) and allow system to drain.
5. On KD2000-KD4000, use engine drainage ports to drain coolant from water pumps and oil cooler.
6. If radiator has mineral deposits or coolant contains dirt/grease, flush and clean cooling system.
7. Otherwise proceed to refill cooling system.

⚠ Hot coolant and steam. Do not add coolant to a hot engine.

1. Remove pressure cap.
2. Close radiator and/or engine block coolant drain valve(s) and tighten hose clamps.
3. Fill cooling system with recommended coolant/antifreeze mixture.
4. Fill coolant expansion tank to middle of sight glass.
5. For KD2000-KD4000, use manual engine venting ports to bleed trapped air.
6. Leave radiator cap off and run for 5 minutes with no load.
7. Stop engine and allow to cool; check and repair leaks.
8. Add coolant to just below overflow tube opening; replace pressure cap; operate until thermostat opens.

⚠ Handling diesel exhaust fluid. Can cause skin, eye, respiratory irritation.

Tools: strap wrench or filter wrench, anti-static gloves, goggles

1. Disable generator set and remove from service; wear anti-static gloves and goggles.
2. Disconnect wiring harness from sleeve.
3. Remove three screws and loosen and remove sleeve.
4. Remove filter; use strap wrench or filter wrench if needed.
5. Clean surrounding surfaces of DEF filter and manifold.
6. Replace O-ring on filter manifold; lubricate with P80 or DEF.
7. Lubricate seal of new filter with DEF or distilled water; fill new filter about 2/3 full with DEF; thread onto manifold.
8. Tighten filter to 30 Nm (22 ft. lbs.) then additional 120°; reinstall sleeve; reconnect harness; reset run time in Kodia; run 30 minutes.

⚠ Explosive fuel vapors. Use extreme care when handling fuels.

1. Disable generator set and remove from service.
2. Hold suitable container beneath fuel/water separator.
3. Open vent plug and manually operated drain.
4. Close drain when fuel free of water flows from separator.
5. Use manual primer pump to prime filter until fuel flows from vent plug.
6. Close vent plug.

⚠ Hazardous voltage. Moving parts. Operate only when all guards and electrical enclosures are in place.

Tools: grease gun

1. Disable generator set and remove from service.
2. Inject grease at remotely located grease fittings on left-hand side of radiator.
3. Grease slowly to prevent over-greasing.
4. Remove any excess grease.
5. Reconnect engine starting battery(ies), negative lead last, and return to service.

⚠ Explosive fuel vapors. Use extreme care when handling fuels.

Tools: strap wrench or filter wrench

1. Disable generator set and remove from service.
2. Close fuel shut-off valve if present.
3. Disconnect fuel-in-water sensor.
4. Open vent plug and remove water drain plug to drain fuel.
5. Remove element from mounting head by twisting counterclockwise.
6. Remove bowl from element; inspect components; lubricate O-ring with clean diesel fuel.
7. Install bowl onto new element; lubricate and install assembly onto mounting head.
8. Replace drain plug; connect sensor; open fuel valve; prime with manual primer pump.

Tools: Flash drive, PC (spreadsheet program)

1. Check for the flash drive symbol at the top of the screen.
2. In the navigation menu, touch Data Log.
3. Confirm USB Connected; touch the Circle icon with three dots near the upper right.
4. Touch to select a category.
5. Touch each parameter you want to log; a check mark appears in each selected box.
6. Click the blue Log Rate box; select the desired log rate and touch the up arrow.
7. Touch START LOG to begin collecting data.
8. Touch STOP to end data logging; wait at least 5 seconds before removing the flash drive.

⚠ Have setup and adjustments performed only by an authorized Kohler distributor.

⚠ The access level login expires after 1 hour.

Tools: External flash drive, SiteTech software, PC

1. Use an external flash drive or SiteTech to export configuration data and save the file.
2. Log in with the Operator or Technician level password.
3. In the navigation menu, touch Setup.
4. Touch the desired category (Electrical, Engine, etc.).
5. Touch the desired subcategory.
6. Touch the blue box with the setting you wish to change; a keypad window opens.
7. Use the keypad to enter the new setting and touch the green arrow.
8. Check the setting for the new value.

⚠ Hazardous voltage. Moving parts. Operate only when all guards and electrical enclosures are in place.

1. Operate generator set under load for 30–60 minutes maintaining exhaust temperature at rated kW.
2. Apply voltage and check for alarms or faults.
3. Check for leaks, vibrations, or abnormal noises.
4. Ensure exhaust gas color is normal.
5. Check engine parameters (oil pressure, coolant temperature).
6. Check electrical parameters (voltage, frequency, current, rotating magnetic field).
7. If fitted, check automatic filling devices (fuel or oil).