Doosan P086 TI Engine

Shared across brands: Caps, Doosan

This engine also powers 3 machine(s) on Power Equipment Info.

How to read your Doosan engine serial & model number →

• Warning fault operates
  Fix: Check relevant switch and wiring of fault indicated on LCD display; Check configuration of input
• Unit shuts down
  Fix: Check DC supply voltage is not above 35 Volts or below 9 Volts; Check the operating temperature is not above 70°C; Check the DC fuse
• Unit is inoperative / Read/Write configuration does not operate
  Fix: Check the battery and wiring to the unit; Check the DC supply; Check the DC fuse
• Starter motor inoperative
  Fix: Check wiring to starter solenoid; Check battery supply; Check battery supply is present on the Starter output of module; Ensure oil pressure switch or sensor is indicating the 'low oil pressure' state to the controller
• Shutdown fault operates
  Fix: Check relevant switch and wiring of fault indicated on LCD display; Check configuration of input
• Pre-heat inoperative
  Fix: Check wiring to engine heater plugs; Check battery supply; Check battery supply is present on the Pre-heat output of module; Check pre-heat configuration is correct
• Module appears to 'revert' to an earlier configuration
  Fix: When editing a configuration using the PC software it is vital that the configuration is first 'read' from the controller before editing it. This edited configuration must then be 'written' back to the controller for the changes to take effect; When editing a configuration using the fascia editor, be sure to press the Auto Mode button to save the change before moving to another item or exiting the fascia editor
• Low oil Pressure fault operates after engine has fired
  Fix: Check engine oil pressure; Check oil pressure switch/sensor and wiring; Check configured polarity (if applicable) is correct (i.e. Normally Open or Normally Closed) or that sensor is compatible with the module and is correctly configured
• Incorrect reading on Engine gauges / Fail to stop alarm when engine is at rest
  Fix: Check engine is operating correctly; Check that sensor is compatible with the module and that the module configuration is suited to the sensor
• Inaccurate generator measurements on controller display
  Fix: Check that the CT primary, CT secondary and VT ratio settings are correct for the application; Check that the CTs are wired correctly with regards to the direction of current flow (p1, p2 and s1, s2) and additionally ensure that CTs are connected to the correct phase (errors will occur if CT1 is connected to phase 2); Remember to consider the power factor (kW = kVA x powerfactor); The controller is true RMS measuring so gives more accurate display when compared with an 'averaging' meter such as an analogue panel meter or some lower specified digital multimeters; Accuracy of the controller is better than 1% of full scale. Generator voltage full scale is 415V ph-N, accuracy is ±4,15V (1% of 415V)
• High engine temperature fault operates after engine has fired
  Fix: Check engine temperature; Check switch/sensor and wiring; Check configured polarity (if applicable) is correct (i.e. Normally Open or Normally Closed) or that sensor is compatible with the module
• Generator fails to start on receipt of Remote Start signal
  Fix: Check Start Delay timer has timed out; Check signal is on 'Remote Start' input; Confirm correct configuration of input is configured to be used as 'Remote Start'; Check that the oil pressure switch or sensor is indicating low oil pressure to the controller; Depending upon configuration, then set will not start if oil pressure is not low
• Fail to Start is activated after pre-set number of attempts to start
  Fix: Check wiring of fuel solenoid; Check fuel; Check battery supply; Check battery supply is present on the Fuel output of the module; Check the speed-sensing signal is present on the module's inputs; Refer to engine manual
• Engine runs but generator will not take load
  Fix: Check Warm up timer has timed out; Ensure generator load inhibit signal is not present on the module inputs; Check connections to the switching device; Note that the set will not take load in manual mode unless there is an active load signal
• Electrical Trip fault operates
  Fix: Check relevant switch and wiring of fault indicated on LCD display; Check configuration of input

Compiled from service & troubleshooting documentation across every generator set that uses the Doosan P086 TI.

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Parts listed by aftermarket suppliers as fitting this engine — leads compiled from supplier catalogs; verify the exact part for your serial number.