Cummins/Onan KTTA-19-G Engine

How to read your Cummins/Onan engine serial & model number →

• The FAULT 1 or FAULT 2 fault lamp lights. Engine shuts down immediately, engine runs for several seconds and then shuts down, or engine continues to run FAULT 1
  Cause: The standard undesignated fault functions are programmed to shut down the set when a fault is sensed. Fault 1 is timed delayed while Fault 2 is immediate. The nature of the fault is an optional selection that is determined when the set installation is designed. The undesignated fault functions may also be programmed for non-shutdown or non-time delay.
• SWITCH OFF lamp flashes
  Cause: Indicates Run-Stop-Remote switch is in the Stop position which will prevent automatic starting
  Fix: Moving the Run-Stop-Remote switch to the Remote position will stop the lamp flashing and enable automatic starting.
• PRELO OIL PRES lamp lights. Engine continues to operate. PRELO OIL PRES
  Fix: Indicates engine oil pressure has dropped to 20 psi (138 kPa). If generator is powering critical loads and cannot be shut down, wait until next shutdown period and then follow step 5 procedure. If engine can be stopped, follow procedure in step 5.
• PRELO OIL PRES lamp lights. Engine continues to operate
  Cause: Indicates engine oil pressure has dropped to 20 psi (138 kPa)
  Fix: If generator is powering critical loads and cannot be shut down, wait until next shutdown period and then follow step 5 procedure. If engine can be stopped, follow procedure in step 5.
• PRE HI ENGINE TEMP lamp lights. Engine continues to operate. PRE HI ENGINE TEMP
  Fix: Indicates engine has begun to overheat and engine temperature has risen to approximately 205° F (97°C). If generator is powering non-critical and critical loads, and cannot be shut down, use the following: a. Reduce load if possible by turning off non-Critical loads. b. Check air inlets and outlets and remove any obstructions to airflow. c. Open doors or windows in generator area to increase ventilation. If engine can be stopped, follow procedure in step 3.
• PRE HI ENGINE TEMP lamp lights. Engine continues to operate
  Cause: Indicates engine has begun to overheat and engine temperature has risen to approximately 205° F (97°C)
  Fix: If generator is powering non-critical and critical loads, and cannot be shut down, use the following: Reduce load if possible by turning off non-critical loads; Check air inlets and outlets and remove any obstructions to airflow; Open doors or windows in generator area to increase ventilation. If engine can be stopped, follow procedure in step 3.
• OVERCRANK lamp lights and engine stops cranking. Or. Engine runs, shuts down, and LO OIL PRES lamp lights
  Cause: Indicates possible fuel system problem
  Fix: Check for empty fuel tank, fuel leaks, or plugged fuel lines and correct as required; Check for dirty fuel filter and replace if necessary (see MAINTENANCE section); Check for dirty or plugged air filter and replace if necessary (see MAINTENANCE section); Refer to step 5; Reset the control and restart after correcting the problem. Contact your distributor for service if none of the above applies.
• No AC output voltage. (Note: If unit is equipped with an excitation breaker (located on back side of output box, near regulator box), confirm it is at ON position.)
  Cause: Voltage regulator is inoperative
  Fix: Refer to Initial Start and Checks, and Adjustments sections of your Installation Manual for voltage check and adjustment procedures. Contact your distributor if voltage build-up is still a problem.
• LO OIL PRES lamp lights. Engine shuts down. LO OIL PRES
  Fix: Indicates engine oil pressure has dropped to 14 psi (97 kPa). Check oil level, replenish as necessary. Check oil lines and filters for leaks, repair as required. Reset control and restart. Contact your distributor if oil pressure is not in the range of 50 to 70 psi (345 to 483 kPa).
• LO OIL PRES lamp lights. Engine shuts down
  Cause: Indicates engine oil pressure has dropped to 14 psi (97 kPa)
  Fix: Check oil level, replenish as necessary. Check oil lines and filters for leaks, repair as required. Reset control and restart. Contact your distributor if oil pressure is not in the range of 50 to 70 psi (345 to 483 kPa).
• LO FUEL lamp lights. Engine shuts down and LO OIL PRES lamp lights. LO FUEL
  Fix: Indicates engine has run out of fuel. Check fuel level and replenish as required.
• LO FUEL lamp lights. Engine shuts down and LO OIL PRES lamp lights
  Cause: Indicates engine has run out of fuel
  Fix: Check fuel level and replenish as required.
• LO FUEL lamp lights. Engine continues to run. LO FUEL
  Fix: Indicates diesel fuel supply is running low. Check fuel supply and replenish as required.
• LO FUEL lamp lights. Engine continues to run
  Cause: Indicates diesel fuel supply is running low
  Fix: Check fuel supply and replenish as required.
• LO ENG TEMP lamp lights. Set is in standby mode but is not operating. (Lamp lights when engine coolant temperature is 70° F (21° C) or lower. Since the lamp goes out after the engine warms up, there should be no cause for alarm if it remains lighted during initial generator set operation.)
  Cause: Indicates engine coolant heater is not operating or is not circulating coolant
  Fix: Check for the following conditions: Coolant heater not connected to power supply. Check for blown fuse or disconnected heater cord and correct as required; Check for low coolant level and replenish if required. Look for possible coolant leakage points and repair as required; Contact your distributor if none of the above applies.

Compiled from service & troubleshooting documentation across every generator set that uses the Cummins/Onan KTTA-19-G.

Parts cataloged across all variants of this engine family — verify the exact part fits your specific variant and serial number before ordering.