Home›Engines›Cummins/Onan KTA50-D(M2)

Cummins/Onan KTA50-D(M2) Engine

Name: Cummins/Onan KTA50-D(M2) Engine
Brand: Cummins/Onan

The Cummins/Onan KTA50-D(M2) is a 50 L 16-cylinder turbocharged/low temperature aftercooled engine rated at 1800 rpm. It powers generator sets from Cummins/Onan, including the KTA50.

Also known as: CUMMINS KTA50-D(M2)

Part of the Cummins/Onan KTA50 engine family — 13 variants share parts & fitment.

50.0 L

Displacement

Cylinders

1800 rpm

Rated speed

On this pageSpecs Generator sets FAQ Service intervals Torque & specs Fluids Procedures

Engine specifications

Displacement	50.0 L
Cylinders	16
Aspiration	Turbocharged/Low Temperature Aftercooled
Rated speed	1800 rpm

Generator sets powered by this engine

Cummins/Onan KTA50

How to read your Cummins/Onan engine serial & model number →

Service intervals

Item	Action	Hours	Months	Notes
Air cleaner element - restriction	Check	250 hr	6 mo	Replace air cleaner element as required
All belts	Check	250 hr	6 mo
Cooling fan	Check	250 hr	6 mo	Check for cracks, loose rivets, bent or loose blades
Engine oil	Change	250 hr	6 mo	Whichever occurs first
Fan idler pivot arm	Lubricate	250 hr	6 mo	Water pump type grease until grease appears
Front engine support	Lubricate	250 hr	6 mo	Chevron SRI grease or equivalent
Fuel filter	Replace	250 hr	6 mo
Hoses	Inspect	250 hr	6 mo	Check/replace as required
Oil filters	Change	250 hr	6 mo	Change filters with oil
Pulley tensioner	Check	250 hr	6 mo
Batteries	Check	1500 hr	12 mo
Cold start aids	Check	1500 hr	12 mo	Seasonal
Crankshaft end clearance	Inspect	1500 hr	12 mo
Engine (steam clean)	Clean	1500 hr	12 mo	Before conducting any 1500 hour maintenance
Engine mounting bolts and nuts	Check	1500 hr	12 mo	Tighten loose; inspect rubber
Engine protection system	Check	1500 hr	12 mo
Fan idler pulley tensioner	Adjust	1500 hr	12 mo
Heat exchanger zinc plugs (marine only)	Check	1500 hr	12 mo	Change if 50 percent eroded
Valves and injectors	Adjust	1500 hr	12 mo	First service — Initial adjustment at 1500 hours; thereafter not again before 6000 hour injector calibration
Air compressor	Inspect	6000 hr	24 mo	Discharge and intake checks
Coolant	Change	6000 hr	24 mo	Clean and flush cooling system
Crankcase breather element	Replace	6000 hr	24 mo	Clean/replace
Engine protection system	Adjust	6000 hr	24 mo	Calibrate
Fan hub	Inspect	6000 hr	24 mo	End clearance and grease leakage
Fan idler pulley assembly	Replace	6000 hr	24 mo	Rebuild or replace as necessary
Fuel pump	Clean	6000 hr	24 mo	Clean and calibrate
Injectors	Clean	6000 hr	24 mo	Clean and calibrate
Thermostats and seals	Replace	6000 hr	24 mo
Turbocharger	Inspect	6000 hr	24 mo
Vibration damper	Inspect	6000 hr	24 mo	Replace after 24,000 hours; K2000 dampers replaced every 12,000 hours
Water pump	Replace	6000 hr	24 mo	Rebuild or replace

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Service specifications

Type	Item	Value	Unit	Condition
Clearance	Crankshaft end clearance	0.13 MIN / 0.51 MAX	mm
Clearance	Fan hub bearing end clearance	0.03 MIN / 0.15 MAX	mm
Clearance	Thermostat seal installation depth	no more than 0.51	mm	below top of cast edge
Clearance	Turbocharger BB (RR-151) and (RR-153) end clearance	0.09 MIN / 0.13 MAX	mm
Clearance	Turbocharger BB bearing radial clearance - RR-151	0.75 MAX	mm	0.030 in
Clearance	Turbocharger BB bearing radial clearance - RR-153	0.55 MAX	mm	0.021 in
Clearance	Turbocharger axial end play - HC5A	0.05 MIN / 0.13 MAX	mm
Clearance	Turbocharger axial end play - HT7100	0.06 MIN / 0.16 MAX	mm
Clearance	Turbocharger axial end play - T18A	0.10 MIN / 0.23 MAX	mm
Clearance	Turbocharger radial clearance compressor impeller - HC5A	0.15 MIN / 0.45 MAX	mm
Clearance	Turbocharger radial clearance turbine wheel - HC5A	0.20 MIN / 0.55 MAX	mm
Gap	Heat exchanger zinc plug erosion limit A	approximately 19	mm	0.75 in; new 51 mm [2 in]
Gap	Heat exchanger zinc plug erosion limit B	approximately 6.4	mm	0.25 in; new 16 mm [0.625 in]
Other	Air compressor discharge carbon deposit thickness limit	2	mm	1/16 in
Other	Alternator belt tension	356	N	80 lbf, Burroughs tension gauge GT-1293
Other	Maximum vibration damper thickness - Houdaille	66.38	mm	2.574 in
Other	Maximum vibration damper thickness - Made in England Before F-82	65.91	mm	2.595 in
Other	Maximum vibration damper thickness - Made in England F-82 and After	65.66	mm	2.585 in
Other	PTD injector travel verification specification	7.80 MIN / 7.82 MAX	mm
Other	PTD non-top stop injector travel adjustment	7.82	mm
Other	PTD non-top stop injector travel limits	7.77 to 7.87	mm
Other	Two pulley fan drive belt tension (set)	2668.9 to 2891.3	N	600 to 650 lbf
Other	Two pulley fan drive belt tension (verify)	2891.3 to 3336.2	N	650 to 750 lbf
Other	Vibration damper thickness variation (four readings 90 degrees apart)	must not vary more than 0.25	mm	0.010 in
Pressure	Coolant pressure cap minimum	50	kPa	7 psi
Pressure	Exhaust back pressure maximum	75	mm Hg	3 in Hg, at rated speed and load
Pressure	Maximum allowable intake restriction - clean filter element	380	mm H2O	15 in H2O
Pressure	Maximum allowable intake restriction - dirty filter element	635	mm H2O	25 in H2O
Pressure	Maximum allowable restriction to fuel pump - clean filter	100	mm Hg	4 in Hg, at rated power
Pressure	Maximum allowable restriction to fuel pump - dirty filter	200	mm Hg	8 in Hg, at rated power
Pressure	Maximum allowable return line restriction	63	mm Hg	2.5 in Hg
Pressure	Maximum allowable return line restriction with check valves and/or overhead tanks	165	mm Hg	6.5 in Hg
Pressure	Oil pressure, main oil rifle, maximum at rated RPM	483	kPa	15W-40 oil at 107 C [225 F]
Pressure	Oil pressure, main oil rifle, minimum at idle RPM	138	kPa	15W-40 oil at 107 C [225 F]
Pressure	Oil pressure, main oil rifle, minimum at rated RPM	310	kPa	15W-40 oil at 107 C [225 F]
Pressure	Throttle air cylinder leak test pressure	689	kPa	100 psi
Pressure	Throttle air cylinder test pressure	560	kPa	80 psi
Speed	Engine speed must not exceed	2400	RPM	under any circumstances
Temperature	LTA modulating thermostat range	74 - 82	C	165 - 180 F
Temperature	Oil temperature maximum	120	C	250 F
Temperature	Standard modulating thermostat range	80 - 90	C	175 - 195 F
Torque	Air compressor unloader valve body capscrew	15	Nm	120 in-lb
Torque	Air compressor unloader valve cap	40	Nm	30 ft-lb
Torque	Alternator adjusting link and mounting capscrews	55	Nm	40 ft-lb
Torque	Crosshead adjusting screw lock nut (with ST-669 adapter)	35	Nm	25 ft-lb
Torque	Crosshead adjusting screw lock nut (without adapter)	40	Nm	30 ft-lb
Torque	Fan belt idler assembly capscrews	60	Nm	45 ft-lb
Torque	Fan hub assembly to fan support (12 pt capscrew)	285	Nm	210 ft-lb
Torque	Fan idler arm shock absorber capscrews	60	Nm	45 ft-lb
Torque	Fan idler control rod adjusting screw jam nuts	55	Nm	40 ft-lb
Torque	Fan idler control rod capscrews	90	Nm	65 ft-lb
Torque	Fuel pump drive coupling capscrews	45	Nm	35 ft-lb
Torque	Injector adjusting screw (alignment/setting)	11 then 10	Nm	100 in-lb then 90 in-lb
Torque	Injector adjusting screw lock nut (with ST-669 adapter)	45	Nm	35 ft-lb
Torque	Injector adjusting screw lock nut (without adapter)	60	Nm	45 ft-lb
Torque	Injector hold down clamp capscrew	16	Nm	145 in-lb
Torque	Injector jumper tube connector screw	25	Nm	20 ft-lb
Torque	Oil drain plug	100	Nm	75 ft-lb
Torque	Rocker lever cover	40	Nm	30 ft-lb
Torque	Rocker lever shaft (12 pt capscrew)	90	Nm	65 ft-lb

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Recommended fluids

Fluid	Grade	Standard	Notes
Coolant	50/50 low-silicate antifreeze and quality water	ASTM D4985 (less than 0.10% silicate as Na2SiO5)	Must be pre-charged with supplemental coolant additives (DCA4) to 1.5 units per gallon; never below 1.2 or above 3 units per gallon. Do not use soluble oils.
Engine oil	SAE 15W-40	API CE or CF4 (CD or CD/SF where CE/CF4 not available)	Multigrade preferred; sulfated ash limit must not exceed 1.85 mass percent. Arctic operation (below -23 C) use synthetic CE/SF 5W-30.
Fuel	ASTM No. 2 diesel		Below 0 C use blends of No. 2D and No. 1D. Viscosity must be kept above 1.3 cSt. Do NOT mix gasoline or alcohol with diesel fuel.
Grease	Water pump type grease (Amoco Rykon Premium No. 2 / Chevron SRI / Exxon Unirex N2 / Shell Dolium R / Texaco Premium RB)		Fan idler pivot arm and front engine support lubrication

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Procedures

Alternator Belt Adjustment adjustment

⚠ Over-tensioning of alternator belts can result in premature accessory drive bushing wear and seal leakage.

Tools: GT-1293 Burroughs Tension Gauge

Loosen the alternator and adjusting link mounting capscrews.
Loosen the jam nuts on the adjusting screw.
Turn the adjusting screw clockwise to tighten the belt tension.
Check the belt tension with a gauge.
Tighten the jam nuts on the adjusting screw to 55 Nm [40 ft-lb].
Tighten the adjusting link and alternator mounting capscrews to 55 Nm [40 ft-lb].
Check the belt tension again.

Crossheads - Adjustment adjustment

Tools: ST-669 Torque Wrench Adapter

Adjust the crossheads on the cylinder that has both valves closed.
Loosen the crosshead adjusting screw locknuts on the intake and exhaust valve crossheads.
Turn the adjusting screw out at least one turn.
Hold the crosshead down against its guide.
Turn the adjusting screw in until it touches the top of the valve stem but does not raise the crosshead.
Hold the adjusting screw and tighten the lock nut to the torque value.

Dipstick Calibration adjustment

⚠ The dipstick will break if the scribe mark is too deep.

Tools: scribe

Drain the oil from the pan.
Install the dipstick in the dipstick tube.
Use clean 15W-40 oil to fill the oil pan to the specified low level.
Remove the dipstick and scribe a mark across the dipstick at the oil level. Mark the low level with an L.
Install the dipstick and add additional oil to the specified full level.
Remove the dipstick and scribe a mark across the dipstick at the oil level. Mark the high oil level with an H.

PT (type D) Injector - Adjustment adjustment

⚠ The injector plunger is under spring tension. Do NOT allow the tool to slip.

⚠ Prevent damage to the indicator by allowing the lever to return slowly.

Tools: 3822575 injector and valve adjustment kit, 3822574 rocker lever actuator, ST-669 Torque Wrench Adapter

Assemble the parts of an injector and valve adjustment kit, Part No. 3822575, or equivalent, and install it on the cylinder.
Adjust the indicator so the tip touches the top of the injector plunger.
Lower the indicator 12.25 mm [0.5 inch] to allow for travel. Lock the indicator support to the post.
Use a rocker lever actuator, Part No. 3822574, or equivalent. Depress the lever until the injector bottoms two or three times.
Hold the lever with the injector plunger firmly bottomed and set the indicator to ZERO.
Turn the adjusting screw until the indicator reads the specified travel.
Tighten the locknut to the torque value.
Check the injector adjustment and repeat if not within specification.

Valves - Adjustment adjustment

⚠ Use the correct chart for the engine being serviced or the parts will be damaged.

Tools: 3376592 Inch Pound Torque Wrench, ST-669 Torque Wrench Adapter, feeler gauge

Select a feeler gauge for the correct valve lash specification and insert the gauge between the rocker lever and the crosshead.
Torque wrench method: use Part No. 3376592 inch pound torque wrench and tighten the adjusting screw to 0.68 Nm [6 in-lb].
Feel method: use a screwdriver and turn the adjusting screw only until the lever touches the feeler gauge.
The adjusting screw must not turn when the locknut is tightened.
Tighten the locknut to the value indicated.
The feeler gauge must slide backward and forward with only a slight drag.
Attempt to insert a feeler gauge 0.03 mm [0.001 in] thicker; the lash is not correct when the thicker gauge will fit.
Repeat until clearance is correct on both intake and exhaust valves.

Air Cleaner Element Replacement - Single Heavy Duty Dry-Type maintenance

⚠ Holes, loose end seals, dented sealing surfaces and other damage require immediate element replacement.

⚠ Pull the cover and element straight out to avoid damage.

Wipe dirt from the cover and upper portion of the air cleaner before disassembly.
Loosen the wing bolt and band clamp securing the dust pan.
Loosen the wing nut and remove the dust shield from the dust pan. Clean the dust pan and shield.
Remove the wing nut securing the primary element and inspect the rubber sealing washer.
Remove the dirty cleaner element and install the new primary element.
Make sure the rubber sealing washer is in place under the wing nut before tightening.
Assemble the dust shield and dust pan and secure with the band clamp.

Coolant Filter Replacement maintenance

⚠ Do NOT remove the radiator cap from a hot engine.

⚠ Do not allow oil to get in the filter; it will adversely affect the DCA.

Remove the coolant system pressure cap and close the shutoff valve(s), if equipped, before removing the coolant filter.
Push in the knob on the filter head or close the gate valve.
Lubricate the seal on the new filter with engine oil.
Install the new coolant filter. Turn the filter until the seal touches the filter head.
Turn the filter an additional 1/2 to 3/4 of a turn after contact.
Pull the knob on the filter head out or open the gate valve.

Cooling System Cleaning and Changing Antifreeze maintenance

⚠ Do not use caustic cleaners in the cooling system. Aluminum components will be damaged.

⚠ Wait until the temperature is below 50 C [120 F] before removing the coolant system pressure cap.

Drain the cooling system. Do not allow the cooling system to dry out. Do not remove the coolant filter.
Add 3.8 liters [1 U.S. gallon] of Fleetguard RESTORE (or equivalent) for each 38 to 57 liters [10 to 15 gallons] of cooling system capacity and fill with plain water.
Turn the heater temperature switch to high to allow maximum coolant flow.
Operate the engine at normal operating temperatures (at least 85 C [185 F]) for 1 to 1 1/2 hours.
Shut the engine off and drain the cooling system.
Fill with clean water to flush and operate at high idle for 5 minutes above 85 C [185 F].
Shut the engine off and drain. Repeat flushing if the water is still dirty.
Refill the system with new heavy duty coolant and SCA.

Fan Hub Inspection maintenance

Tools: dial indicator

Remove the fan belt.
Rotate the fan hub pulley to check for rough or damaged bearings.
Inspect the pulley grooves for excessive wear.
Check for grease leakage.
Use a dial indicator to check the bearing end clearance.
Replace with a new or rebuilt unit as necessary.
Install the fan belt.

Fuel Filter(s) Replacement maintenance

Tools: 3375049 filter wrench

Clean the area around the fuel filter head and replace the fuel filter(s).
Use a filter wrench, Part No. 3375049, to remove the fuel filter.
Clean the filter head gasket surface with a clean, lint-free towel.
Apply a light film of clean engine oil to the filter gasket surface.
Fill the filter with clean fuel.
Install the filter on the filter head and tighten until the gasket contacts the filter head surface.
Tighten the filter per the filter manufacturer's instructions.

Lubricating Oil and Oil Filter Changing/Replacement maintenance

⚠ Avoid direct contact of hot oil with your skin.

⚠ Fill the oil filters with clean lubricating oil before installation.

Tools: 3375049 oil filter wrench

Operate the engine until water temperature reaches 60 C [140 F]. Shut off the engine.
Remove the oil drain plug and drain the oil immediately.
Clean the area around the lubricating oil filter head and the gasket surface.
Use an oil filter wrench, Part No. 3375049, or equivalent, to remove the oil filters.
Apply a light film of lubricating oil to the gasket sealing surface before installing the new filters.
Fill the oil filters with clean lubricating oil.
Install the filters as specified by the filter manufacturer.
Check and clean the oil drain plug threads and seal surface.
Install and tighten the oil drain plug to 100 Nm [75 ft-lb].
Fill the engine with clean oil to the correct level.
Operate the engine at idle to inspect for leaks; shut off and check oil level again; add oil to the high H mark.

Short Term Storage Preparation (One Month to 6 Months) maintenance

⚠ Put a warning tag on the engine: The engine does NOT contain oil. Do NOT operate the engine.

Operate the engine at HIGH IDLE until coolant temperature is 70 C [160 F]. Turn the engine OFF.
Disconnect the fuel lines to the engine fuel filter and the injector return line.
Put both fuel lines in a container of diesel fuel and START the engine.
After the engine runs smoothly, transfer the fuel supply line to a container of preservative oil and operate until preservative oil flows out the injector return line.
Turn the engine OFF and connect the fuel lines to the fuel filter and injector return line.
Drain the oil pan sump, oil filters, and fuel filters.
Disconnect the electrical wiring from the fuel pump solenoid; turn the fuel pump manual shutoff valve counterclockwise until it stops.
Crank the engine slowly and spray lubricating oil into the intake manifold and air compressor inlet.
Drain the coolant and put a warning tag on the engine.
Store the engine in a dry area with uniform temperature and bar the crankshaft two or three revolutions every 3 to 4 weeks.

Extracted from the manufacturer documentation linked to this model. Values are copied as printed; confirm against your unit's manual and serial number.

Parts cataloged across the Cummins/Onan KTA50 family

298

Part #	Description	Category
140-2096	Element, Primary (Outer)	air_filter
140-2097	Cleaner, Air (Includes Elements)	air_filter
140-2467	Element, Safety (Inner)	air_filter
140-2501	Cleaner, Air (Disposable)	air_filter
140-2502	Band, Mounting	air_filter
140-2503	Bracket, Mounting	air_filter
140-3163	Cleaner, Air (No Replaceable Element)	air_filter
140-3230	Cleaner, Air (Includes Elements - See Ref. No. 25 and 26)	air_filter
309-0272	Regulator, Voltage - 24 VDC (Used on 35 A MP Alternator)	alternator
503-1743-01	Alternator & Orive Components Group Pulley, Alternator - Multi Groove (Use with 35 AMP Alternator)	alternator
206587	CAP, MAIN BEARING	bearing_cap
206588	CAP, MAIN BEARING	bearing_cap
98-5347	Decal - Caution Fan Drive & Lube Components Group Belt.	belt
106069	SCREW, HEXAGON HEAD CAP	bolt
205584	SCREW, TWELVE POINT CAP	bolt
206028	SCREW, SOCKET HEAD CAP	bolt
3032633	SCREW, TWELVE POINT CAP	bolt
3177945	SCREW, HEX FLANGE HEAD CAP	bolt
3628452	SCREW, HEXAGON HEAD CAP	bolt
S-112	SCREW, HEXAGON HEAD CAP	bolt
205684	BRACKET, LIFTING	bracket_lifting
205230	BUSSING	bushing
0300-4623-29	DFLB (600V)	current_transformer
0300-4623-30	DFLC (600V)	current_transformer
0300-4623-52	DFLB BR (0-480V)	current_transformer
0300-4623-54	DFLC BR (0-480V)	current_transformer
3178803	CYLINDER BLOCK OPTION BP6089	cylinder_block
3178910	CYLINDER BLOCK	cylinder_block
148582	DOE, PIN	dowel_pin
70662	DOE, PIN	dowel_pin
3629497	DRAINCOCK	draincock
206224	PLUG, EXPANSION	expansion_plug
206742	PLUG, EXPANSION	expansion_plug
3629168	PLUG, EXPANSION	expansion_plug
122-0757	Filter. Water - W/Corosion Inhibiting Chemical	filter
159-1445	Reservoir, Fuel	fluid
FS1216	Fuel/Water Sep Spin-On	fuel_filter
121-0113	Gasket, Pump	gasket
121-0117	Gasket, Hand Hole	gasket
205059	WASHER, PLAIN	gasket
3002993	DOE, RING	gasket
3025485	WASHER, PLAIN	gasket
3176857	DOE, RING	gasket
3178450	WASHER, PLAIN	gasket
3178457	WASHER, PLAIN	gasket
M-4352581	Upper Gasket Set	gasket
S-604	WASHER, LOCK	gasket
S-610	WASHER, LOCK	gasket
338-2278	Harness. Wiring - AC (Includes Terminal Block & Cable Ties) [Used only with meters]	harness
338-2529	Harness. Wiring	harness
128-0108	Insulation, Hose - Bulk (7/8º ID) (Order By The Foot - 10 Feet Required)	hose
130-5588-02	Tube, Water Heater	hose
130-5589-02	Tube, Water Heater	hose
130-5590-02	Tube, Water Heater	hose
130-5591-02	Tube, Water Heater	hose
338-2925	Hose, Radiator	hose
501-0704	Line, Flexible Fuel - Fuel Out	hose
501-0707	Line, Flexible Fuel - Fuel In	hose
502-1162	Connector, Hose (3/8")	hose
503-0183	Clamp, Hose	hose
503-0685	Clamp, Hose	hose
503-0868	Clamp, Hose - T-Bolt Type (3.5" NON)	hose
503-1140	Hose, Rubber	hose
503-1484	Elbow, Hose (45 Deg) (7" ID)	hose
503-1620	Hose – Bulk (3/8" ID) (Order by the Foot)	hose
503-1727	Hose, Radiator (3” ID x 10”)	hose
503-1728	Hose (3” ID x 5–1/2”)	hose
503-1870-11	Clamp, Hose	hose
503-1870-12	Clamp, Hose	hose
505-0324	Hose. Bulk (Sold by the Foot) Two Feet Required Nipple, Pipe - Half (3/4 NPT x 2"LG)	hose
98-5759	Drive - Multi Groove Hose, Flexible - Lube (Grease)	hose
98-5842	Clamp, Hose - T-Bolt Type (3.5" NON)	hose
3822575	Injector and valve adjustment kit	injector
3011884	INSERT, LINER	insert_liner
3019150	INSERT, LINER	insert_liner
3021148	INSERT, LINER	insert_liner
206580	BEARING, MAIN	main_bearing
206581	BEARING, MAIN A/R No.2,3,4,5,6,7,&8, Upper	main_bearing
206582	BEARING, MAIN A/R No.2,3,4,5,6,7,&8, Upper	main_bearing
206583	BEARING, MAIN A/R No.2,3,4,5,6,7,&8, Upper	main_bearing
206584	BEARING, MAIN A/R No.2,3,4,5,6,7,&8, Upper	main_bearing
206590	BEARING, MAIN	main_bearing
206591	BEARING, MAIN A/R No.2,3,4,5,6,7,&8, Lower	main_bearing
206592	BEARING, MAIN A/R No.2,3,4,5,6,7,&8, Lower	main_bearing
206593	BEARING, MAIN A/R No.2,3,4,5,6,7,&8, Lower	main_bearing
206594	BEARING, MAIN A/R No.2,3,4,5,6,7,&8, Lower	main_bearing
206600	BEARING, MAIN	main_bearing
206601	BEARING, MAIN A/R No.1&9, Upper	main_bearing
206602	BEARING, MAIN A/R No.1&9, Upper	main_bearing
206603	BEARING, MAIN A/R No.1&9, Upper	main_bearing
206604	BEARING, MAIN A/R No.1&9, Upper	main_bearing
206610	BEARING, MAIN	main_bearing
206611	BEARING, MAIN A/R No.1&9, Lower	main_bearing
206612	BEARING, MAIN A/R No.1&9, Lower	main_bearing
206613	BEARING, MAIN A/R No.1&9, Lower	main_bearing
206614	BEARING, MAIN A/R No.1&9, Lower	main_bearing
3018210	SET, MAIN BEARING STANDARD	main_bearing_set
3018211	SET, MAIN BEARING A/R .010 Inch O/S	main_bearing_set
3018212	SET, MAIN BEARING A/R .020 Inch O/S	main_bearing_set
3018213	SET, MAIN BEARING A/R .030 Inch O/S	main_bearing_set
309-0561	Alternator & Drive Components Group Pulley. Alternator - Multi Groove (Use with 35 A MP Alternator)	oil_filter
LF3325	Lube, Full-Flow Spin-On	oil_filter
016-40820	Harness, Wiring (Includes Cable Ties and Terminals)	other_service
102-1335	Plug, Oil Drain	other_service
121-0116	Cover, Hydraulic Hole	other_service
130-2981	Cap. Radiator - 7#PSI	other_service
130-3538	Chemical DCA4 Service Pre-Charging Complete System	other_service
130-3576	Decal - Ground	other_service
130-3758	Radiator (includes Cap)	other_service
140-1260	Fitting, Safety Filter	other_service
140-1548	Indicator, Service	other_service
140-2098	Hood, Air Inlet (Includes Mounting Clamp)	other_service
140-2099	Band	other_service
140-2395	Tube, Air Inlet	other_service
140-2504-01	Bracket - Right Side	other_service
140-2504-02	Bracket - Left Side	other_service
140-2508	Tube, Air Inlet	other_service
140-2509	Tube, Air Inlet	other_service
140-2515	Bracket, Mounting	other_service
140-2519	Tube, Air Inlet	other_service
140-2521	Tube, Air Inlet	other_service
140-2528	Shield	other_service
191-1926-02		other_service
300-2856	Board Assy, Printed Circuit	other_service
300-2863	Board Assy, Printed Circuit - Relay Assembly- (A14)	other_service
3007525	Liner Kit STD	other_service
301-9054-01	Decal - Panel Front Markings (Control With Meters)	other_service
301-9054-02	Clip - Fastener	other_service
301-9054-03	Clip - Fastener	other_service
3012611	Liner Kit +.010" UPF	other_service
3012612	Liner Kit +.020" UPF	other_service
302-1720	Meter, Frequency (M23)	other_service
302-1753	Ammeter (M22) See Current Transformer & Ammeter Installation Figure for Parts)	other_service
302-1800	Ammeter (M22) Scale in Amps as Indicated 0-2000/0-4000 (600 VAC Application) 0-3000/0-6000 (120-480 VAC Application)	other_service
302-1908	Screw. Cap - Hex Head (M8-1.25 x 35MM)	other_service
305-0818-02	EOOO-21002	other_service
307-1056	Relay. 24 VDC	other_service
307-1987	Clip. Relay	other_service
308-0882	Decal - Panel Front Markings (Control Without Meters)	other_service
309-0436	Switch, Thermostatic - High Water Temperature (PRE-ALARM)(216"F) Switch. Thermostatic - High Water Temperature (SHUTDOWN)	other_service
309-0437	(222"F)	other_service
309-0635-02	Valve, Check	other_service
3096680	Piston STC 13.8:1 Ratio	other_service
3096681	Piston KT Series 15.5:1 Ratio	other_service
3096682	Piston KTA Series 14.5:1 Ratio	other_service
3096683	Piston 13.5:1 Ratio	other_service
3096684	Piston KTA 15.7:1 Ratio	other_service
3096685	Piston STC 13.9:1 Ratio	other_service
319-0447	Bracket. Mounting - Relay	other_service
319-0754	Tie. Cable	other_service
322-0363	Component 322-0363	other_service
323-0804	Screw. Machine - Round Head with IT Lock Washer (#6-32 x 1/2")	other_service
323-1200	# Socket, Contact (Used in J1, J2)	other_service
323-1304	tiotming, Umector	other_service
323-1306	Genset component (SJB series)	other_service
3318201	Battery Cable Group	other_service
332-0052	Clamp, Loop	other_service
332-0607	Block, Terminal (T81)	other_service
332-1279	Terminal. Lug - Ring (3/8	other_service
332-1292	Terminal Board (Includes Parts Marked #)	other_service
332-1445	Tie. Cable	other_service
332-1673	Terminal, Wire - Spade	other_service
332-2634	Clamp, Retainer 4 Prior To December 1996 Production (Mounted On Top And Side Of Control Box Wrapper)	other_service
332-2723	Strip. Marker	other_service
333-0677-01	Heater, Coolant - 4990 Watt	other_service
333-0677-02	Heater, Coolant - 6420 Watt	other_service
338-1835	Harness, Wiring (A13 to A l l )	other_service
338-1836	Harness, Wiring (A14 to A l l )	other_service
338-1904	Harness. Wiring (A15 to All)	other_service
338-2532	Terminal. Lug - Forked (No. 6 Screw)	other_service
355-0093	Voltmeter (M21) Dual Scale 0-300/0-600V Single Scale 0-750V	other_service
3628731	Piston STC Kit	other_service
3630913	Piston KTA-50-G7	other_service
3631241	Piston Kit STC 13.9:1 Ratio	other_service
3631242	Piston Kit 13.5:1 Ratio	other_service
3631243	Piston Kit KTA 15.7:1 Ratio	other_service
3631244	Piston Kit KTA Series 14.5:1 Ratio	other_service
3631245	Piston Kit KT Series 15.5:1 Ratio	other_service
3631246	Piston Kit STC 13.8:1 Ratio	other_service
3801268	Liner Kit +.030" UPF	other_service
3803530	Piston Assembly STC	other_service
3804747	Piston Kit KTA-50-G7	other_service
3804885	Piston KTA-50-G8/G9	other_service
406-0333	Component 406-0333	other_service
406-0334	Clip, Retaining - Turnbutton Fastener	other_service
4089847	Piston Kit GTA38/19	other_service
4090013	Piston Kit KTA-38-M2	other_service
4090029	Piston Kit QSK19CE	other_service
4090181	Piston GTA38/19	other_service
4097889	Piston KTA-38-M2	other_service
4910463	Piston QSK19R/M	other_service
4910465	Piston QSK Series	other_service
4916177	Piston GTA/GQSK19	other_service
4918058	Piston QSK19CE	other_service
4922319	Piston QSK19C	other_service
4955233	Piston Kit QSK19R/M	other_service
4955235	Piston Kit QSK Series	other_service
4955236	Piston Kit QSK19C	other_service
4955238	Piston Kit GTA/GQSK19	other_service
501-0520	Screw, Cap - Hex Head (3/8-24 x 5/8")	other_service
501-0524	Washer, Lock - EIT (3/8")	other_service
501-0558	Line. Flexible - Bypass	other_service
503-1717	Elbow, Reducer (45 Deg) (7" ID to 6" ID)	other_service
503-1720	Insert, Reducer (6" OD to 5-1/2" ID)	other_service
503-1730		other_service
504-0028	Valve, Radiator Drain	other_service
505-0007	Belt. Drive - Multi Groove (Used with 35 A MP Alternator * Pulley, Alternator - Multi Groove (Use with 75 A MP Alternator)	other_service
505-0017	Bushing, Pipe – Reducer (3/8" to 1/4")	other_service
505-0021	Bushing, Pipe - Reducer (3/4º to 1/2º)	other_service
505-0100	Nipple, Pipe - Close (1/2”)	other_service
505-0102	Filter. Water - W/Corosion Inhibiting	other_service
505-0117	Bushing, Reducer - Flush, Brass (1/2' NPT x3/8° NPT)	other_service
505-0132	Nipple, Pipe - Close (3/4 NPT x l-3/8"LG) Elbow. Pipe - 90* (3/4 NPT)	other_service
505-0376	Elbow – 45 Deg (3/8")	other_service
508-0015	Washer, Insulating - Fiber (#8)	other_service
511-0161-02	.*	other_service
517-0131	Capacitor (Used across Voltmeter Terminals on some Sets)	other_service
518-0548-24	Clamp, Retainer Begin December 1996 Production (Mounted On Top And Side Of Control Box Wrapper On The Side Towards The Control Box Cover)	other_service
518-0548-42	Clamp, Retainer 4 Prior To December 1996 Production (Mounted On Top And Side Of Control Box Wrapper)	other_service
526-0030	Washer, Flat (3/8")	other_service
800-0055	Screw, Cap – Hex Head (3/8–16 x 2-1/4")	other_service
800-0062	Nut, Insulated	other_service
800-0094	Screw, Cap – Hex Head (1/2–13 x 2")	other_service
800-0270	DCA4 Service Pre-Charging Complete System	other_service
800-2060	Screw, Cap - Hex Head (M8x 1.25 x35)	other_service
809-0035	Screw, Machine - Thread Cutting, Round Head (#8 X 3/4')	other_service
812-0063	Screw, Machine - Round Head	other_service
812-0065	Screw, Machine - Round Head (#6 - 32 x 5/8')	other_service
812-0084	Screw, Machine - Round Head (#8-32 x 1)	other_service
815-0388	Bracket. Mounting - Relay Lead(s), Electrical Wire, Electrical - 20 AW G, Insulated Terminal, Wire - Forked, 18-20 Gauge	other_service
815-0544	Screw, Machine - Round Head IT Washer (#6 - 32 x 1/2')	other_service
821-0004	Screw, Self-Locking - Hex	other_service
821-0029	Screw, Self–Locking – Hex Washer Head (3/8–16 x 3/4")	other_service
821-0033	Screw, Self–Locking – Hex Washer Head (7/16–14 x 3/4")	other_service
821-5004-03	Screw, Self-Locking – Hex Washer Head (3/8–16 x 1")	other_service
850-0050	Washer, Lock - Spring (3/8”)	other_service
853-0003	Washer, Lock - ET (#6)	other_service
856-0008	Washer, Lock - EIT (5/16'1)	other_service
856-0010	Washer, Lock - EIT (3/8')	other_service
870-0131	Nut. Hex - with ET (#10-32)	other_service
870-0196	Nut, Insulating (#8)	other_service
870-0281	Nut, Self-Locking – Hex Washer Head (3/8–16)	other_service
900-0181	PCC Control Service Manual	other_service
960-0602		other_service
960-0606		other_service
960-0608		other_service
98-2235		other_service
98-4732	Caution	other_service
98-4798	Decal - Caution "7# PSI HOT WATER SYSTEM"	other_service
98-5298	Decal - Panel Rear Markings (All Control Panels)	other_service
98-5299	Decal - Panel Rear Markings (All Control Panels)	other_service
98-5316	Decal - Panel Rear Markings (All Control Panels)	other_service
98-5387	Nut, Self-Locking - with ET Lockwasher (#10-32)	other_service
98-5393	Screw, Tapping - Round Head (#8 x 3/4")	other_service
98-5822	Bushing, Reducer - Flush (1/2 NPT x 3/8 NPT)	other_service
98-6108-03	Decal - Model Identification	other_service
98-6111-03	ONAN GEN SET CUMMINS GEN SET	other_service
98-6139-03	CUNMINS ONAN GEN SET	other_service
98-6169	Terminal Assembly (Includes Replaceable Items 26 thru 29)	other_service
F-2375	A single line drawing of the prime power system	other_service
M-3804747	Piston Kit	other_service
68445	PIN, GROOVE	pin
3628605	PLUG, PIPE	pipe_plug
3628607	PLUG, PIPE	pipe_plug
3178464	PLATE, COVER	plate_cover
121-0111	Drive, Pump	pump
159-1451	Pump, Fuel Transfer	pump
3011076	SEAL, D RING	seal
3014668	SEAL, D RING	seal
3081489	SEAL, OIL	seal
3177556	SEAL, RECTANGULAR RING	seal
509-0283-01	Seal	seal
509-0336	Seal, O-Ring	seal
509-0337	Seal, O-Ring	seal
149-2232	Indicator, Air Restriction (Includes Fitting)	sensor
193-0244	Sender, Pressure - 0i1	sensor
193-0375	# Sender, Water Temperature	sensor
309-0269	Switch, Low Engine Temperature (S4)	sensor
960-0181		service_manual
960-0302		service_manual
960-0504	PCC Control Service Manual	service_manual
960-0507	Detector Control Service Manual	service_manual
3033853	SHAFT, IDLER	shaft_idler
3175281	SHAFT, IDLER	shaft_idler
205741	SHIM, A/R .007 Inch O/S	shim
205742	SHIM, A/R .008 Inch O/S	shim
205743	SHIM, A/R .009 Inch O/S	shim
205744	SHIM, A/R .020 Inch O/S	shim
205745	SHIM, A/R .031 Inch O/S	shim
3000138	SUPPORT, BEARING	support_bearing
309-0649	Thermostat	thermostat
3000139	BEARING, THRUST	thrust_bearing
3001708	BEARING, THRUST A/R .010 Inch O/S	thrust_bearing
3001709	BEARING, THRUST A/R .020 Inch O/S	thrust_bearing
3001710	BEARING, THRUST A/R .030 Inch O/S	thrust_bearing
3001711	BEARING, THRUST A/R .040 Inch O/S	thrust_bearing
3179664	VALVE, PISTON COOLING	valve_piston_cooling
508-0292	Washer, Sealing - Copper	washer

Parts cataloged across all variants of this engine family — verify the exact part fits your specific variant and serial number before ordering.

Common questions

What is the displacement of the Cummins/Onan KTA50-D(M2)?

The Cummins/Onan KTA50-D(M2) has a displacement of 50.0 liters with 16 cylinders.

Which generators use the Cummins/Onan KTA50-D(M2) engine?

The Cummins/Onan KTA50-D(M2) powers 1 generator set(s), including Cummins/Onan KTA50.