DSE6010 Controller

The DSE6010 is a generator-set controller.

Specifications

Protections	IP65 (Front of module when module is installed into the control panel with the optional sealing gasket), IP42 (front of module when module is installed into the control panel WITHOUT being sealed to the panel), NEMA 12 (Front of module when module is installed into the control panel with the optional sealing gasket), NEMA 2 (front of module when module is installed into the control panel WITHOUT b
Digital inputs	["Auxiliary Digital inputs"]
Analog inputs	["Auxiliary Analogue inputs"]
Communications	CAN
Relay outputs	["Close Gen Output", "Close Gen Output Pulse", "Emergency Stop", "Energise To Stop", "Flexible Sensor High Shutdown", "Flexible Sensor High Warning", "Flexible Sensor Low Shutdown", "Flexible Sensor Low Warning", "Open Gen Output", "Open Gen Output pulse"]
Dimensions	216mm x 158mm x 42mm (8.5” x 6.2” x 1.6”)

Troubleshooting

Fault codes

Code	Meaning	Cause
807	Gas On Delay (Gas Engine Only)
808	Gas Ignition Off Delay (Gas Engine Only)
809	Crank Disconnect On Oil Pressure Enable
810	Check Oil Pressure Prior To Starting
811	Crank Disconnect On Frequency
812	Under Speed Enable
815	Over Speed Trip
817	Low Battery Volts Enable
824	High Battery Volts Warning Delay
825	Charge Alt Shutdown Trip Enable
826	Charge Alt Shutdown Trip
827	Crank Disconnect On Oil Threshold
828	Crank Disconnect On Engine Speed
830	Low Battery Start Arming
832	Low Battery Start Threshold
Generator High Voltage Shutdown	Generator High Voltage Shutdown	The generator output voltage has risen above the preset level
Generator Low Voltage Shutdown	Generator Low Voltage Shutdown	The generator output voltage has fallen below the preset level
High Coolant Temperature Shutdown	High Coolant Temperature Shutdown	The module detects that the engine coolant temperature has exceeded the high engine temperature shutdown setting after the Safety On timer has expired.
Loss of Mag. Pickup Signal	Loss of Mag. Pickup Signal	The speed signal from the magnetic pickup is not being received by the DSE controller.
Low Fuel Level	Low Fuel Level	The module detects that the fuel level is below the configured setting
Low Oil Pressure Shutdown	Low Oil Pressure Shutdown	The engine oil pressure has fallen below the low oil pressure trip setting level after the Safety On timer has expired.
Over Frequency Shutdown	Over Frequency Shutdown	The generator output frequency has risen above the preset level
Over Speed Shutdown	Over Speed Shutdown	The engine speed has exceeded the pre-set trip
Under Frequency Shutdown	Under Frequency Shutdown	The generator output frequency has fallen below the preset level
Under Speed Shutdown	Under Speed Shutdown	The engine speed has fallen below the pre-set trip after the Safety On timer has expired.

Symptoms & remedies

Symptom	Cause	Remedy
Battery High Voltage	The DC supply has risen above the high volts setting level for the duration of the high battery volts timer
Battery Low Voltage	The DC supply has fallen below the low volts setting level for the duration of the low battery volts timer
CAN ECU Warning	The engine ECU has detected a warning alarm and has informed the DSE module of this situation. The exact error is also indicated on the module’s display.
Charge Alternator Failure	The auxiliary charge alternator voltage is low as measured from the W/L terminal.
Digital Input A-D	Auxiliary Digital inputs can be user configured as Digital inputs and will display the relevant icon.
Analogue Input A-C	Auxiliary Analogue inputs can be user configured as Digital inputs and will display the relevant icon.
Fail To Stop	The module has detected a condition that indicates that the engine is running when it has been instructed to stop. ‘Fail to Stop’ could indicate a faulty oil pressure sensor - If engine is at rest check oil sensor wiring and configuration.
Generator High Voltage Warning	The generator output voltage has risen above the pre-set pre-alarm setting.
Generator Low Voltage Warning	The generator output voltage has fallen below the pre-set pre-alarm setting after the Safety On timer has expired.
High Coolant Temperature Warning	The module detects that the engine coolant temperature has exceeded the high engine temperature pre-alarm setting level after the Safety On timer has expired.
Low Oil Pressure Warning	The module detects that the engine oil pressure has fallen below the low oil pressure pre-alarm setting level after the Safety On timer has expired.
Low Fuel Level	The module detects that the fuel level is below the configured setting
Over Frequency Warning	The generator output frequency has risen above the pre-set pre-alarm setting.
Over Speed Warning	The engine speed has risen above the overspeed pre alarm setting
Under Frequency Warning	The generator output frequency has fallen below the pre-set pre-alarm setting after the Safety On timer has expired.
Under Speed Warning	The engine speed has fallen below the underspeed pre alarm setting
Flexible Sensor	The flexible sensor warning alarm has been triggered.
CAN ECU Data Fail	The module is configured for CAN operation and does not detect data on the engine Can datalink.	The engine shuts down.
CAN ECU Shutdown	The engine ECU has detected a shutdown alarm and has informed the DSE module of this situation. The exact error is also indicated on the module’s display.
Emergency Stop	The emergency stop button has been depressed. This is a failsafe (normally closed to battery negative) input and will immediately stop the set should the signal be removed.	NOTE:- The Emergency Stop Negative signal must be present otherwise the unit will shutdown.
Fail To Start	The engine has not fired after the preset number of start attempts
Temperature sensor open circuit	Temperature sensor has been detected as being open circuit.
Oil pressure sensor open circuit	Oil pressure sensor has been detected as being open circuit.
Magnetic pickup open circuit	Magnetic pickup sensor has been detected as being open circuit.
ry Volts
CAN ECU Power
CAN ECU Stop
Charge Alternator Shutdown
Charge Alternator Warning
Close Gen Output
Close Gen Output Pulse
Common Alarm
Common Electrical Trip
Common Shutdown
Common Warning
Energise To Stop
Fuel Relay
Gas Choke On
Gas Ignition
Generator Available
Generator High Volts Shutdown
Generator Low Volts Shutdown
Low Oil Pressure Shutdown
Flexible Sensor High Shutdown
Flexible Sensor High Warning
Flexible Sensor Low Shutdown
Flexible Sensor Low Warning
Oil Pressure Sender Open Circuit Alarm
Temperature Sender Open Circuit Alarm

Fault codes and symptom→remedy steps extracted from this controller’s service/owner documentation; verify against the official manual before servicing. Extracted directly from this controller's manual.